720686
8
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
8
Electrical Connection
Be sure your power supply agrees with the nameplate
marking. A voltage decrease of 10 percent or more will
cause a loss of power and overheating. All B&D tools are
factory tested. If this tool does not operate, check the power
supply.
Familiarization
Place the saw on a smooth, flat surface such as a
workbench or strong table. Examine Figures 1 & 2 and refer
to the parts description to become familiar with the saw and
its various parts. The following section on adjustments will
refer to these terms and you must know what and where the
parts are. The part name is followed by the corresponding
part number Example - lock down pin (10). Press down
lightly on the operating handle and pull out the lock down
pin (10), as shown in Figure 3. Gently release the downward
pressure and allow the arm to rise to its full height. Use the
lock down pin when carrying the saw from one place to
another. Use the operating handle (1) to transport the saw
or the hand indentations (11) shown in Figure 2 after
unplugging.
Specifications
Capacity of cut
47° mitre left and right
47° bevel left
0° mitre -Max. Height 3-1/2” -Max. Width 5-1/2”
45° mitre -Max. Height 3-1/2” -Max. Width 4-1/8”
45° bevel -Max. Height 2-1/2” -Max. Width 5-1/2”
Bench Mounting
Bench mounting holes (8) are provided in all four feet to
facilitate bench mounting, as shown in Figure 1. (Two
different sized holes are provided to accommodate different
sizes of screws. Use either hole, it is not necessary to use
both.) Always mount your saw firmly to prevent movement.
To enhance the tool’s portability, it can be mounted to a
piece of 1/2" or thicker plywood which can then be clamped
to your work support or moved to other job sites and
reclamped.
NOTE: If you elect to mount your saw to a piece of plywood,
make sure that the mounting screws don’t protrude from the
bottom of the wood. The plywood must sit flush on the work
support. When clamping the saw to any work surface, clamp
only on the clamping bosses where the mounting screw
holes are located. Clamping at any other point will interfere
with the proper operation of the saw.
CAUTION: To prevent binding and inaccuracy, be
sure the mounting surface is not warped or
otherwise uneven. If the saw rocks on the surface,
place a thin piece of material under one saw foot until the
saw sits firmly on the mounting surface.
Installing a New Saw Blade
(UNPLUG THE MITRE SAW)
DO NOT USE FERROUS METAL or masonry cutting blades
in this saw
Loosen hex bolt on center cover counter clockwise with
box wrench.
Lift up the safe cover and center cover.
Press down the lock to lock spindle.
Loosen hex bolt clockwise with box wrench, then
dismount the bolt and flange.
Mount the blade of saw on spindle. Make sure that the
arrow direction on surface of saw blade is same as one
of the cover.
Note: There are two different internal diameters of cutter in
inner plate which have steel stamp marked 25.4mm 16mm.
When mounting, the outer diameter of inner plate must be
correspondent with the internal diameter of saw blade.
Mount flange and hex bolt.
Press axle lock and tighten hex bolt counter clock wise
with box wrench firmly, then tighten hex bolt clockwise to
fix centre cover.
Note: Only use attached wrench when mounting or
dismounting saw blade. When dismounting saw blade, lift up
safe cover and centre cover. Loosen hex bolt with box
wrench and disassemble hex bolt, flange and saw blade.
NEVER DEPRESS THE SPINDLE LOCK PIN WHILE THE
BLADE IS ROTATING.
Be sure to hold the guard bracket down and firmly
tighten the guard bracket screw when you finish installing
the saw blade. Failure to do so will cause serious
damage to the saw.
Assembling and Adjusting Your Saw
PERFORM ALL ASSEMBLY WITH SAW UNPLUGGED.
Attach Mitre Clamp Handle
Remove the mitre clamp handle (4) from the plastic parts
bag and carefully thread it into the bracket in the front of the
saw.
Attaching Dust Bag
A zippered cloth dust bag is included with your saw. To
attach the bag, fit the plastic opening firmly over the dust
spout (9).
NOTE: The saw can also be used with a vacuum cleaner
hose attached to the dust spout or without any attachment.
Adjustments
PERFORM ALL ADJUSTMENTS WITH THE MITRE SAW
UNPLUGGED
ENGLISH (Original instructions)
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STSM1510 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STSM1510 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info