720594
40
Verklein
Vergroot
Pagina terug
1/240
Pagina verder
40
Disassembly of the Tubes
1. Place the hedge cutter on a clean flat surface and
loosen the screw of the connection piece. Pull the latch
protection from the notch.
2. Push the latch down. This releases the lock of the
connecting piece. See A41.
3. Pull the upper tube out of the connection piece.
Mounting of the cutting attachment
Warning!
The blades are very sharp. Do not handle the blades,
if the blade cover is not covered. Always wear gloves
when you work with or in the vicinity of the blade.
1. Make sure that the cutting attachment in the storage/
transport position is locked (folded back) and the blade
cover is pulled over the blade.
2. Push the outer tube up to the limiting stop in the
clamping of the transmission housing.
The outer tube must be fully pushed into the
transmission housing. If you feel a resistance before
the limiting stop, turn the outer tube until the splines of
the inner main shaft (drive shaft) snaps into place in the
transmission housing and push the outer tube up to the
limiting stop.
3. Turn the gearbox housing/Cutting attachment so that
the index bolt is aligned in an upright position over the
hole
. The cutting attachment is located in the reverse
position (in the bearing position/transport position).
A42
1
2
3
1). Blade cover
2). Align with hole in outer tube and tighten the index
screw
3). Tighten the clamping screw finally
A43
2
1
1). Place the hand protection so that the tip of the
cutting attachment in the recess (if the hedge cutter is in
the warehouse/transport position).
2). Tighten clamping
4. Use an Allen key (4 mm), to first tighten the index bolt
on the gearbox housing and then the clamping screw.
5. Align the hand protection in such a way that the tip
of the cutting attachment is lying correctly in the recess.
Make sure that the cutting attachment is not jammed in
the slot. Then tighten the screw of hand protection with
a screwdriver.
A41
G
B
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STR-4 in 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STR-4 in 1 in de taal/talen: Duits, Engels, Frans, Italiaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 9,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info