720594
26
Verklein
Vergroot
Pagina terug
1/240
Pagina verder
26
5.2 Stop and switch off
Let go of the throttle lever (8).
- Let the engine to return without gas to the idle speed
and let the device to continue to run for 10 to 15
seconds.
- Set the operating switch (3) on the operating handle to
"STOP".
7. Working with the brush cutter / grass
trimmer
- Familiarize yourself - if the device is switched off - first
with the operation and holding, if you are working with
the Petrol- brush cutter work for the first time.
- The Petrol-brush cutter has to be designed in such a
way that they are held by the operator only on the right
side of the body’s side.
- Hold the petrol-brush cutter tight always with both
hands on the handles.
- Hold the operating handle with your right hand and
with the left hand the handle of the hand bar.
- Always make sure that the cutting tool still continues
to rotate for a short time after the throttle is released.
- Always ensure you have a good engine idle speed, so
that the cutting tool does not rotate any more when the
throttle is pressed.
- Work with high speed, and thus you will have the best
cutting results.
- Hold the device with evenly curved movement from left
to right and back again.
Then cut the next length.
Caution: Direct the device always back only again to the
initial position before you cut the next length.
- If you bump into a stone or a tree while working, switch
off the engine and disconnect the spark plug connectors
and inspect the Petrol-brush cutter for damage.
Caution: When working in difficult terrain and slopes,
please be especially careful. In case of high grass, cut
gradually in order not to overload the device. First cut
the tips, work then gradually.
Always wear safety glasses and a hearing protection
and during deforestation work, a protective helmet.
7.1 Mowing with a thread head
- Use the thread cartridge to maintain a clean cut also of
uneven edges, fence posts and trees.
- Guide the trim line carefully past an obstacle and cut
with the thread tip around the obstacle. In case the trim
line comes in contact with rocks, trees and walls, the
thread becomes frayed prematurely or breaks.
- Never replace the plastic thread never by a metal wire
- Risk of injury!
7.2 Mowing with a cutter blade
- Use the cutter blade to thin out scrub, uncontrolled
growth, young stocks of trees (maximum 2 cm trunk
diameter) and tall grass.
- While using the metal cutting tools, there is always the
danger of a backlash, if the tool comes into contact with
a solid obstacle (rocks, trees, branches etc.).
While doing so, the device is thrown back against the
direction of rotation.
- In case of uncontrolled growth and scrub, let the cutter
blad to "dive" from above. Through this, the material to
be cut is chopped.
ATTENTION: Follow the procedures for this work
technology with caution, because the greater the
distance of the cutting tool to the ground, the greater
the risk that the material to be cut and foreign objects
are thrown to the side.
For an adequate protective equipment during the use,
care has to be taken as per the operating instructions.
All other usages are ruled out. The user / operator is
responsible for injuries resulting damage or injury due to
incorrect use.
and not the manufacturer. Only 4-teeth blades suitable
for the machine as mentioned in the operating manual
may be used.
G
B
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STR-4 in 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STR-4 in 1 in de taal/talen: Duits, Engels, Frans, Italiaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 9,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info