720752
11
Verklein
Vergroot
Pagina terug
1/226
Pagina verder
11
GB
4.
Mark
a
on the center of the beam on the wall.
5.
Turn the laser 90º clockwise so that the left-most
end of the laser line is displayed near
a
(Figure
D
2
).
6.
Mark
b
on the center of the beam on the wall.
7.
Measure the vertical distance between
a
and
b
.
8.
If your measurement is greater than the
Allowable Distance Between
a
and
b
for the
corresponding Distance Between Walls in the
following table, the laser must be serviced at an
authorized service center.
Distance
Between Walls
Allowable Distance
Between
a
and
b
30′ (9m) 15/32” (12mm)
40′ (12m) 9/16” (14.4mm)
50′ (15m) 23/32” (18mm)
Horizontal Beam - Pitch Direction
Checking the horizontal pitch calibration of the
laser requires a single wall at least 30′ (9m) long.
It is important to conduct a calibration check using
a distance no shorter than the distance of the
applications for which the tool will be used.
1.
Place the laser against the end of the wall
(Figure
E
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
At least 30′ (9m) apart along the laser beam,
mark
a
and
b
.
4.
Move the laser to the opposite end of the wall
(Figure
E
2
).
5.
Position the laser toward the rst end of the same
wall and parallel to the adjacent wall.
6.
Adjust the height of the laser so the center of the
beam is aligned with
b
.
7.
Directly above or below
a
, mark
c
along the
laser beam (Figure
E
3
).
8.
Measure the distance between
a
and
c
.
9.
If your measurement is greater than the
Allowable Distance Between
a
and
c
for the
corresponding Distance Between
a
and
b
in
the following table, the laser must be serviced at
an authorized service center.
Distance Between
a
and
b
Allowable Distance
Between
a
and
c
30′ (9m) 15/32” (12mm)
40′ (12m) 9/16” (14.4mm)
50′ (15m) 23/32” (18mm)
Vertical Beam - Plumb
Checking the vertical (plumb) calibration of the
laser can be most accurately done when there is
a substantial amount of vertical height available,
ideally 30′ (9m), with one person on the oor
positioning the laser and another person near a ceiling
to mark the position of the beam. It is important to
conduct a calibration check using a distance no
shorter than the distance of the applications for which
the tool will be used.
1.
On the oor between two walls, mark a 5 ft.
(1.5 m) line that is parallel to the adjacent wall
(Figure
F
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
Place the laser at one end of the line on the oor,
making sure the vertical laser beam is aligned
and centered on the line.
4.
Where the vertical laser beam appears on the
ceiling, mark
a
. (This should be directly over the
midpoint of the line on the oor.)
5.
Move the laser to the other end of the line on the
oor (Figure
F
2
).
6.
Where the vertical laser beam appears on the
ceiling, mark
b
, directly beside the rst mark
a
.
7.
Measure the distance between
a
and
b
.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STHT77498-1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STHT77498-1 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 5,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info