720780
9
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
9
(Original instructions) ENGLISH
Description (Fig. 1)
Warning: Never modify the power tool or any part
of the tool, otherwise it may cause damage to the
tool or result in personal injury.
a. ON/OFF switch
b. Spindle lock
c. Guard
Purpose of design
This angle grinder is designed especially for grinding.
Do not use sandpaper discs and grinding wheels other than
those with depressed center.
Do not use the tool in wet conditions or environments in the
presence of flammable liquids or gases.
This heavy-duty angle grinder is a professional power tool.
Do not allow children to come in contact with this tool.
Inexperienced operators are required to use this tool under
supervision.
Electrical Equipment Safety
Only one voltage is applicable to this tool. Be sure
to check that the power suuply corresponds to the
voltage on the rating plate. Your STANLEY tool is
equipped with double insulation, hence, it does not require
to be earthed.
When the power cord is damaged, have it sent to a
STANLEY service center for replacement to specially
prepared cables.
Using Extension Cords
If an extension cord is required, please select a 3-phase
extension cord that has been inspected and matches the
input power (see Technical Data) of this tool. The minimum
conductor size is 1.5mm
2
, maximum length is 30 meters.
When using a cable reel, be sure to pull out all the cables.
Assembly and Adjustment
Warning: To minimize the danger of serious
personal injury, please switch off the tool
power and disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling
the tool, press and release the trigger switch to make sure
the tool is already switched off.
Attaching and Removing the Wheel Guard (Fig. B)
Warning To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling
the tool, press and release the trigger switch to make sure
the tool is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (3) collar over the groove
(11) of the gear housing.
3. Turn the guard (4) counterclockwise by 150 degrees.
4. Make sure that the screws (20) are tightened.
Removing the guard
1. Loosen the screws (20) on the guard collar.
2. Pull up the guard (3).
Warning: Do not operate the tool when the safety
guard is not in place.
Fitting and removing a grinding (Fig. C1, C2, C3)
Warning: Do not use damaged grinding wheels.
1. Place the tool on a work bench, guard up.
2. Fit the inner flange (6) correctly onto the spindle (7)
(Fig. C1).
3. Place the disc (8) on the flange (6) (Fig.C2). When fitting
a disc with a raised center, make sure that the raised
centre (9) is facing the flange (6).
4. Screw the out flange (10) onto the spindle (7) (Fig. C3)
- the ring on the flange (10) must fae towoards the disc
when fitting a grinding disc (A)
- the ring on the flange (10) must face away from the
disc when fitting a cutting disc (B)
5. Press the spindle lock (2) and rotate the spindle (7) until
it locks in position (Fig. C2).
6. Tighten the flange (10) with the two-pin spanner
supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (10) with the
two-pin spanner.
Warning: Do not use a damaged disc.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STGL2023 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STGL2023 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info