720444
7
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
Check for damage to the tool, parts or accessories which
may have occurred during transport.
Take the time to thoroughly read and understand this
manual prior to operation.
Description (fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Mode selector
5. Ventilation slots
6. Side handle
7. Depth adjustment rod
8. Keyed chuck
9. Sleeve
10. Chuck key
11.Speed dail
Assembly
Warning! Before assembly, please ensure that the power
tool is powered off and the power plug of the tool is
unplugged from the power source.
Selecting the operating mode (fig. B) The tool can be used in
two operating modes:
Rotary drilling:
for steel, wood and plastics.
Impact drilling:
simultaneous rotating and impacting for concrete and
masonry drilling operations.
Select the required operating mode by rotating the mode
selector (4) to the required position.
Inserting and removing a bit (fig. A)
Keyed chuck
Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
Put the chuck key (10) into each hole in the side of the
chuck and turn clockwise until tight.
To remove the bit, proceed in reverse order.
Fitting the side handle (fig. A)
The side handle (6) can be fitted to suit both RH- and
LH-users.
Always use the drill with the side handle properly
assembled.
Loosen the side handle.
For RH-users, slide the side handle clamp overthe collar
behind the chuck, handle at the left.
For LH-users, slide the side handle clamp overthe colar
behind the chuck, handle at the right.
Rotate the side handle to the desired positionand tighten
the handle.
Setting the drilling depth (fig. C)
Insert the required drill bit into the chuck.
Slacken the side handle (6).
Fit the depth adjustment rod (7) through the hole in the
side handle clamp.
Adjust the drilling depth as shown.
Tighten the side handle.
Forward/reverse slider (fig. A)
To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
Always wait until the motor has come to a
complete standstill before changing the direction of
rotation.
Chuck removal (fig. D)
Open the chuck jaws as far as possible
Insert a screwdriver into the chuck and remove the
chuck retaining screw (12) by turning clockwise.
Tighten an Allen key into the chuck and strike it with a
hammer as shown.
Instructions for use
Always observe the safety instructions and applicable
regulations.
Be aware of the location of pipework and wiring.
Apply only a gentle pressure to the tool. Excessive force
does not speed up drilling but decreases tool
performance and may shorten tool life.
7
ENGLISH
(Original instructions)
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley STDH8013 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley STDH8013 in de taal/talen: Engels, Frans, Portugees als bijlage per email.

De handleiding is 4,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info