720577
18
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
18
CAUTION:when you operate the machine please
avoid the contact with curbs, stones and other hard
objects, because the cutting line may break and the
trim line automatic stops working.
Maintenance and Care
Gear Lubrication
Check the filling of lubrication grease every 25
hours of operation.
- Use an Allen key to remove the plug screw by
turning (B29).
- When you cannot see any grease on the screw,
fill approx. 5 g lubrication grease (DIY store) into
the gearbox case, and close the ller opening again.
Keep in mind that the gearbox case should never
be completely filled with lubrication grease.
Air filter
After working for longer time, you should clean the air
filter. Dust and pollen plug up the pores of the filter made
of foamed plastic.
- Remove the cover (B30), and wash the filter (B31)
in mild soap water. Caution: Do not use any
gasoline or solvent.
- Dry the filter before you insert it again.
In order not to shorten the service life of the engine, a
damaged air filter must be replaced at once.
Adjustment of Spark Plug
Check the spark plug air gap at least once a year or when
the engine starts poorly. The correct gap
between ignition flag and ignition contact
is 0.6-0.7 mm (B32).
- Wait until the engine has cooled down completely.
- Loose the screw and remove the plastic cover (B33).
- Pull the spark plug cap (B34) off the spark plug,
and use the supplied spark plug wrench to
remove the spark plug by turning (B35).
- When the electrode is severely worn out or
reveals a strong incrustation, the spark plug must
be replaced with an equivalent plug.
A strong incrustation of the spark plug can be
caused by: Amount of oil is too high in the
gasoline mix, poor oil quality, old gasoline mix, or
plugged up air filter.
- Screw the spark plug by hand completely into the
thread. (Avoid jamming it)
- Use the supplied spark plug wrench to tighten the spark
plug.
- When using a torque wrench, the tightening
torque is 12-15 Nm.
- Plug the spark plug socket correctly on the plug.
Trimming the Line Knife
- When the trimming line is no longer cut clean
during feeding, use a file to re-sharpen the cutting edge
(B36). File in one direction and in the
specified angle.
Cleaning
Use a moist piece of cloth to clean the plastic parts.
Do not use any cleaning agents, solvents, or sharp
objects.
During the course of work, wet grass and weed
wraps around the drive shaft below the cutting
guard for technical reasons. Remove this, otherwise the
engine will overheat because of too much friction.
Periodical Checks
Keep in mind that following specifications relate to
normal usage. Owing to circumstances (longer
periods of daily work, severe dust exposure, etc.),
the specified intervals will become correspondingly
shorter.
G
B
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SPS-900 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SPS-900 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 3,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info