622242
12
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
12
77137
Set Up
Place laser tool on a fl at, stable surface.
If using the auto levelling feature move the pendulum /
transport lock to the unlocked position. The laser tool must
then be positioned in its upright position on a surface that
is within the specifi ed compensation range.
The laser tool can be placed in any orientation and be
functional only when the pendulum / transport lock is in the
locked position.
Mounting on an Accessories
Position accessory in a place where it will not be easily
disturbed and near the central location of the area to
be measured.
Set up the accessory as required. Adjust positioning to
be sure accessory base is near horizontal (within laser
tools compensation range).
Mount the laser tool to the accessory using the
appropriate fastening method to be used with such
accessory / laser tool combination.
CAUTION:
Do not leave the laser tool unattended on an
accessory without fully tightening the fastening
screw. Failing to do so may lead to the laser tool
falling and sustaining possible damage.
NOTE:
It is best practice to always support laser tool with
one hand when placing or removing laser tool from an
accessory.
Operation
NOTE:
• See LED Descriptions for indications during operation.
Before operating the laser tool always be sure to check the
laser tool for accuracy.
In Manual Mode, Self-Levelling is OFF. The accuracy of the
beam is not guaranteed to be level.
Laser tool will indicate when it is out of compensation
range. Reference LED Descriptions. Reposition laser tool
to be closer to level.
When not in use, please be sure to power OFF the laser
tool and place the pendulum lock in the locked position.
Power
• Press
to turn laser tool ON.
To turn laser tool OFF, repeatedly press
until the
OFF mode is selected OR press and hold
for ≥ 3
seconds to turn laser tool OFF while in any mode.
Mode
• Press
repeatedly to cycle through the available
modes.
Self-Levelling / Manual Mode
(See fi gures
C
and
F
)
The pendulum lock on the laser tool needs to be
switched to the unlocked position to enable self-
levelling.
The laser tool can be used with the pendulum lock in the
locked position when it is required to position the laser
tool at various angles to project non-level straight lines
and/or points (where applicable).
Accuracy Check and
Calibration
NOTE:
The laser tools are sealed and calibrated at the factory to
the accuracies specifi ed.
It is recommended to perform a calibration check prior to
its fi rst use and then periodically during future use.
The laser tool should be checked regularly to ensure its
accuracies, especially for precise layouts.
When performing the accuracy checks, use as large of an
area / distance as possible. The greater the area / distance,
the easier to measure the accuracy of the laser.
Transport lock must be in the unlocked position to
allow the laser tool to self-level before checking
the accuracy.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SLL360 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SLL360 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info