720775
8
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
ENGLISH (Original instructions)
8
PACKAGE CONTENTS
1 Angle grinder
1 Guard
1 Side handle
1 Flange set
1 Two-pin spanner
1 Instruction manual
Check for damage to the tool, parts or accessories which
may have occurred during transport.
Take the time to thoroughly read and understand this
manual prior to operation.
FEATURES (Fig A)
This appliance includes some or all of the following features.
WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
1. Switch
2. Spindle lock
3. Guard
4. Side handle
Purpose of design
This angle grinder is designed especially for grinding.
Do not use sandpaper discs and grinding wheels other than
those with depressed center.
Do not use the tool in wet conditions or environments in the
presence of flammable liquids or gases.
This angle grinder is a professional power tool.
Do not allow children to come in contact with this tool.
Inexperienced operators are required to use this tool under
supervision.
ASSEMBLY
WARNING: To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before
reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
Attaching and removing the wheel guard (Fig. B)
WARNING To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before
reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (3) collar over the groove of
the gear housing.
3. Turn the guard (3) counterclockwise by 150 degrees.
4. Make sure that the screws (12) are tightened.
Removing the guard
1. Loosen the screws (12) on the guard collar.
2. Pull up the guard (3).
WARNING: Do not operate the tool when the safety
guard is not in place.
Fitting and removing a grinding wheel (Fig C1, C2, C3)
WARNING: Do not use damaged grinding wheels.
1. Place the tool on a work bench, guard up.
2. Fit the inner flange (5) correctly onto the spindle (6)
(Fig. C1).
3. Place the disc (7) on the flange (5) (Fig.C2). When fitting a
disc with a raised center, make sure that the raised centre
(8) is facing the flange (5).
4. Screw the out flange (9) onto the spindle (6) (Fig. C3)
- the ring on the flange (9) must face towards the disc
when fitting a grinding disc (C3-A)
- the ring on the flange (9) must face away from the
disc when fitting a cutting disc (C3-B)
LABELS ON TOOL
The label on your tool may include the following symbols:
Position of date code
The date code, which also includes the year of manufacture,
is printed into the housing.
Example:
2017 XX JN
Year of manufacturing
WARNING! To reduce the risk of injury, the user
must read the instruction manual before use.
Wear ear protection.
Wear a dust mask.
Wear safety glasses or goggles.
V Volts
Direct Current
A Amperes n
0
No-Load Speed
Hz Hertz
Class II Construction
W Watts
Earthing Terminal
min minutes
Safety Alert Symbol
Alternating
Current
/min.
Revolutions or
Reciprocation per
minute
edge of wheel has been rounded off, you are free to operate the
grinder in either the A or B direction.
Starting and stopping (Fig A)
WARNING: Before using the tool, check whether the
handle is tightened securely. Check whether the switch is
working normally.
Before plugging in the tool to the power supply, check whether the
switch is in the OFF position.
WARNING: Do not switch the tool on or off while under
load conditions.
Proper hand position (Fig G)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side handle (figure A),
with the other hand on the body of the tool, as shown in figure G.
Switch
CAUTION: Hold the body of the tool firmly to maintain control of the
tool at start up and during use and until the wheel or accessory stops
rotating. Make sure the wheel has come to a complete stop be fore
laying the tool down.
NOTE: To reduce unexpected tool movement, do not switch the tool
on or off while under load conditions. Allow the grinder to run up to
full speed before touching the work surface. Lift the tool from the
surface before turning the tool off. Allow the tool to stop rotating
before putting it down.
WARNING: Before connecting the tool to a power supply,
be sure the slider switch is in the off position by pressing
the front part of the switch and releasing. Ensure the
slider switch is in the off position as described above after
any interruption in power supply to the tool, such as the
activation of a ground fault interrupter, throwing of a
circuit breaker, accidental unplugging, or power failure. If
the slider switch is locked on when the power is
connected, the tool will start unexpectedly.
Lock-On feature of the switch
Press the trigger (1), the tool will start. Keep pressing the trigger,
then slide trigger (1) to the front of the tool, the unit will be locked into
“on“ position. To turn off the tool, press the trigger (1) then loose, the
tool will stop running.
Explanation: Before coming into contact with the object you
are working on, make sure the abrasive wheel is turning at
maximum speed. Before turning off the tool, lift the tool up
from the object you are working on.
CAUTION: Make sure the abrasive wheel is completely
stopped before putting down the tool.
(Original instructions) ENGLISH
9
5. Press the spindle lock (2) and rotate the spindle (6) until it locks
in position (Fig. C2).
6. Tighten the flange (9) with the two-pin spanner supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (9) with the two-pin
spanner.
WARNING: Do not use a damaged disc.
Attaching the Side Handle (Fig D)
WARNING: Before using the tool, check that the handle
is tightened securely.
WARNING: The side handle should always be used to
maintain control of the tool at all times.
Screw the side handle (4) tightly into one of the holes (10) or (11) on
either side of the gear case.
Preparation before use
Attach the safety guard and appropriate abrasive or grinding
wheels. Do not use abrasive or grinding wheels that are overly
worn.
Make sure that the inner and outer flanges are attached
correctly.
Make sure that the abrasive or grinding wheels are rotating in the
direction of the arrows on the accessories and tool.
VOLTAGE DROPS
In rush currents cause short-time voltage drops. Under unfavourable
power supply conditions, other equipment may be affected. If the
system impedance of the power supply is lower than 0.175Ω ,
disturbances are unlikely to occur.
USE (Fig F)
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or
removing/installing any accessory. Before
reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
Make sure all materials to be grinded are secured in position.
Apply slight pressure to the tool. Do not apply side pressure to
the abrasive disc.
Avoid overloading. If the tool becomes hot, let it spin for a few
minutes with no load.
1. Be sure to hold the tool tightly with both hands (one hand on
housing, the other on side handle). Start the tool and bring the
grinding wheel on the workpiece.
2. Keep the edge of the wheel tilted at angle from 15 to 30 degrees
against the surface of the workpiece.
3. When using a new grinding wheel, do not operate the wheel in
the B direction, otherwise, it will cut into the workpiece. When the
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SL209 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SL209 in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 8,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info