720570
9
Verklein
Vergroot
Pagina terug
1/185
Pagina verder
9
Cold starting
– Set ignition switch 10 to "I"/"ON".
– Gently press fuel pump (14) often
enough that no more bubbles are visible
(approx. 5-6 times).
– Move the choke lever (4) to .
– Gently pull the starter grip until you feel
resistance. and then pull the pull starter forcefully
outwards until you hear a first ignition sound.
– Move the choke lever (4) to .
– Gently pull the starter grip until you feel
resistance, and then forcefully pull the starter
outwards until the
motor engages.
– Press switch-on lock 9 and gently activate the
throttle (13) at the same time.
1
2
3
4
12
11
9 8
13
5
10
14
15
16
6
7
Danger !
Danger of injury!
After the appliance has started, slightly
activate the throttle once to ensure that
the motor reaches the correct idling
speed and that the cutting equipment
does not run without a load
Note:
With the choke closed (choke lever at
), pull the pull starter only until you
hear a first ignition sound. Otherwise,
you may run the risk of fuel leaking into
the combustion chamber, which would
prevent an ignition spark.
Warm start
– Set ignition switch to I/"ON".
– Check that the choke lever is at .
– Gently pull the starter grip until you feel
resistance, and then forcefully pull the starter
outwards until the motor engages.
– Press start-up lock and gently activate the
throttle at the same time.
– If the motor does not engage after you pulled
the starter three times, repeat the starting
procedure as described under Motor cold start .
After starting the motor
– Leave the motor running at idling speed for a
while.
– Slowly press down on the throttle to increase
the motor speed.
The clutch will be released when the motor speed
is high enough, and the cutting equipment will
start to run.
– Check that the cutting equipment stops
running when you release the throttle.
Stopping the motor
– Release the throttle.
– Set ignition switch to "STOP".
The motor will switch off.
Cutting hedges
Attention !
Risk of damage to the appliance!
Take particular care close to fences!
If trimmings, fence wire or similar is
caught in the cutting equipment,
switch the appliance off immediately.
– Press the locking button (5), and keep it
pressed.
– Twist the rear handle into the desired position,
and let it engage.
G
B
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley SHT-26-55 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley SHT-26-55 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info