Handleiding Stanley SFMCD715 (pagina 9 van 100) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

720419

Verklein

Vergroot

Pagina terug

1/100

Pagina verder

ENGLISH

(Original instructions)

Please visit our website www.stanley.eu/3 for

further information.

Keyless chuck (Fig. G)

Warning! Make certain the battery pack is removed to prevent

tool actuation before installing or removing accessories.

To insert a drill bit or other accessory:

u Grasp the chuck (5) and rotate it in the counterclockwise

direction, as viewed from the chuck end.

u Insert the bit or other accessory (12) fully into the chuck

and tighten securely by rotating the chuck in the clockwise

direction as viewed from the chuck end.

Warning! Do not attempt to tighten or loosen drill bits (or any

other accessory) by gripping the front part of the chuck and

turning the tool on.

Damage to the chuck and personal injury may occur when

changing accessories.

Trigger switch & forward/reverse button (Fig H)

u The drill is turned ON and OFF by pulling and releasing

the trigger switch (1) shown in gure H. The farther the

trigger is depressed, the higher the speed of the drill.

u A forward/reverse control button (2) determines the

rotational direction of the tool and also serves as a lock

off button.

u To select forward rotation, release the trigger switch and

depress the forward/reverse control button on the right

side of the tool.

u To select reverse, depress the forward/reverse control

button on the left side of the tool.

u The centre position of the control button locks the tool in

the off position. When changing the position of the control

button, be sure the trigger is released.

Adjusting torque control (Fig I)

This tool is tted with a torque adjustment collar (3) to select

the operating mode and to set the torque for tightening

screws. Large screws and hard workpiece materials

require a higher torque setting than small screws and soft

workpiece materials.

u For drilling in wood, metal and plastics, set the collar (3) to

the drilling position symbol.

u For drilling in light masonry, set the collar (3) to the

hammer drilling position.

u For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed

as follows:

u Set the collar to the lowest torque setting.

u Tighten the rst screw.

u If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw.

u Repeat until you reach the correct setting.

u Use this setting for the remaining screws.

Dual range switch (Fig J)

The dual range feature of your drill allows you to shift gears

for greater versatility.

u To select low speed, high torque setting (position1), turn

tool off and permit to stop. Slide gear shifter button (4)

away from the chuck.

u To select the high speed, low torque setting (position 2),

turn tool off and permit to stop. Slide gear shifter button

back toward the chuck.

Note: Do not change gears when tool is running. If you are

having trouble changing gears, make sure that the dual range

gear button is either completely pushed forward or completely

pushed back.

Screw driving

u For driving fasteners, the forward/reverse button should

be pushed to the left.

u Use reverse (button pushed to the right) for

removing fasteners.

Note: When moving from forward to reverse, or vice versa,

always release the trigger switch rst.

Drilling

u Use sharp drill bits only.

u Support and secure work properly, as instructed in the

Safety Instructions.

u Use appropriate and required safety equipment, as

instructed in the Safety Instructions.

u Secure and maintain work area, as instructed in the

Safety Instructions.

u Run the drill very slowly, using light pressure, until the hole

is started enough to keep the drill bit from slipping out of it.

u Apply pressure in a straight line with the bit. Use enough

pressure to keep the bit biting but not so much as to stall

the motor or deect the bit.

u Hold the drill rmly with two hands, one hand on the

handle, and the other gripping the bottom around the

battery area or the auxiliary handle if provided.

u DO NOT CLICK THE TRIGGER OF A STALLED DRILL

OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE

TO THE DRILL CAN RESULT.

u Minimize stalling on breakthrough by reducing pressure

and slowly drilling through the last part of the hole.

u Keep the motor running while pulling the bit out of a drilled

hole. This will help reduce jamming.

u Make sure switch turns drill on and off.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Stanley SFMCD715 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info