720757
7
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
7
ENGLISH
(Original instructions)
guard specic for the intended operation. If the unit is intended
to perform cutting off operations, a guard (17, Fig F) specic
for this operation must be tted .
Fitting
u Place the tool on a table, with the spindle (5) facing up.
u Release the clamping lock (7) and hold the guard (4) over
the tool as shown.
u Align the lugs (8) with the notches (9).
u Press the guard down and rotate it counterclockwise to
the required position.
u Fasten the clamping lock (7) to secure the guard to the
tool.
u If required, tighten the screw (6) to increase the clamping
force.
Removing
u Release the clamping lock (7).
u Rotate the guard clockwise to align the lugs (8) with the
notches (9).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
u Screw the side handle (2) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(g. B - D)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
u Fit the guard as described above.
u Place the inner ange (10) onto the spindle (5) as shown
(g. B). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the disc (11) onto the spindle (5) as shown (g. B).
If the disc has a raised centre (12), make sure that the
raised centre faces the inner ange.
u Make sure that the disc locates correctly on the inner
ange.
u Place the outer ange (13) onto the spindle. When tting
a grinding disc, the raised centre on the outer ange must
face towards the disc (A in g. C). When tting a cutting
disc, the raised centre on the outer ange must face away
from the disc (B in g. C).
u Keep the spindle lock (3) depressed and tighten the outer
ange using the two-pin spanner (14) (g. D).
Removing
u Keep the spindle lock (3) depressed and loosen the outer
ange (13) using the two-pin spanner (14) (g. D).
u Remove the outer ange (13) and the disc (11).
Fitting and removing sanding discs (g. D & E)
For sanding, a backing pad is required. The backing pad is
available from your Stanley Fat Max dealer as an accessory.
Fitting
u Place the inner ange (10) onto the spindle (5) as shown
(g. E). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the backing pad (15) onto the spindle.
u Place the sanding disc (16) onto the backing pad.
u Place the outer ange (13) onto the spindle with the raised
centre facing away from the disc.
u Keep the spindle lock (3) depressed and tighten the outer
ange using the two-pin spanner (14) (g. D). Make sure
that the outer ange is tted correctly and that the disc is
clamped tightly.
Removing
u Keep the spindle lock (3) depressed and loosen the outer
ange (13) using the two-pin spanner (14) (g. D).
u Remove the outer ange (13), the sanding disc (16) and
the backing pad (15).
Use
Warning! Let the tool work at its own pace. Do not overload.
u Carefully guide the cable in order to avoid accidentally
cutting it.
u Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
u Always position the tool in such a way that the guard
provides optimum protection from the grinding or cutting
disc.
Switching on and off
u To switch on, slide the on/off switch (1) forward then press
it in. Note that the tool will continue running when you
release the switch.
u To switch off, press the rear part of the on/off switch.
Warning! Do not switch the tool off while under load.
Soft Start Feature
The soft start feature allows a slow speed build-up to avoid
an initial jerk when starting. This feature is particularly useful
when working in conned spaces.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FME822 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FME822 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info