622143
5
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
5
ENGLISH
(Original instructions)
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Drilling mode selector
5. Tool holder
6. Side handle
7. Depth stop
8. Depth stop lock button
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle (g. C
u Turn the grip counterclockwise until you can slide the side
handle (6) onto the front of the tool.
u Rotate the side handle into the desired position.
u Tighten the side handle by turning the grip clockwise.
Fitting an accessory (g. A)
u Clean and grease the shank (9) of the accessory.
u Pull back the sleeve (10) and insert the shank into the tool
holder (5).
u Push the accessory down and turn it slightly until it ts into
the slots.
u Pull on the accessory to check if it is properly locked. The
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
u To remove the accessory, pull back the sleeve (10) and
pull out the accessory.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, oors or ceilings, check for
the location of wiring and pipes.
Selecting the operating mode (g. B)
The tool can be used in three operating modes. Press in the
button (11) and rotate the drilling mode selector (4) towards
the required position, as indicated by the symbols.
Drilling
u For drilling in steel, wood and plastics, set the operating
mode selector (4) to the
r
position.
Hammer drilling
u For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the
s
position
u When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
u For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (4) to the
q
position.
u Make sure the forward/reverse switch is in the forward
position.
u When changing from hammer drilling to chiselling, turn
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage the
spindle lock.
u When hammering with spindle lock, the angle of the bit
may be changed. Set the operating mode selector (4) to
the position, the angle of the bit may now be changed
by rotating the tool holder (6). Set the operating mode
selector (4) to the
q
position, before continuing.
Selecting the direction of rotation
For drilling, for tightening screws and for chiselling, use for-
ward (clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(3) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FME500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FME500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info