720690
6
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
English
6
(original instructions)
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised STANLEY FATMAX
Service Centre in order to avoid a hazard.
Using an extension cable
Always use an approved extension cable suitable for the
power input of this appliance (see technical data). The
extension cable must be suitable for outdoor use and marked
accordingly. Up to 30 m of 1.5 mm
2
HO5VV-F extension cable
can be used without loss of product performance.
Before use, inspect the extension cable for signs of damage,
wear and ageing. Replace the extension cable if damaged
or defective. When using a cable reel, always unwind the
cable completely.
Features
This tool includes some or all of the following features.
1. Variable Speed trigger switch
2. Blade clamp collar
3. Pivot shoe
4. Saw blade
Assembly
@
Warning! Before attempting any of the following
operations, make sure that the tool is switched off
and unplugged and that the saw blade has stopped.
Used saw blades may be hot.
Fitting the saw blade (g. B)
Hold the tool away from the body
Rotate the blade clamp collar collar (2) anti-clockwise.
Insert the shank of the blade (4) fully into the blade clamp
collar (2).
Release the blade blade clamp collar (2) to lock the blade
into position.
Note The blade can be installed with the teeth up to assist in
ush cutting.
Removing the saw blade (g. B)
@
Warning! Burn hazard: Do not touch the blade
immediately after use. Contact with the blade may
result in personal injury.
Rotate the blade clamp collar (2) anti-clockwise.
Remove blade (4)
Adjusting the pivot shoe (g. C, D)
The retracted blade length should be longer than the width
of the workpiece. If the blade is shorter, the tip will jam in
the workpiece during cutting, possibly causing injury and
damaging the blade or workpiece. To adjust the pivot shoe (3)
and the blade extension:
Loosen both cap screws on the underside of the
front cover.
Adjust the pivot shoe (3) in or out as needed as shown in
gure D .
Tighten the cap screws. Do not over tighten.
Use
@
Warning! Let the tool work at its own pace. Do
not overload.
@
Warning! Never use the tool when the pivot shoe is
loose or removed.
Switching on and off (g. E)
The variable speed on/off switch offers a choice of speeds for
greatly improved cutting rates in various materials.
To switch the tool on, press the variable speed switch (1).
The speed depends on how far you depress the switch.
To switch the tool off, release the variable speed switch.
To switch the tool off, when in continuous operation, press
the variable speed switch once more and release it.
Sawing
Always hold the tool with both hands.
Let the blade run freely for a few seconds before starting
the cut.
Apply only a gentle pressure to the tool while performing
the cut.
If possible, work with the pivot shoe plate (4) pressed
against the workpiece. This will improve tool control and
reduce tool vibration, as well as prevent the blade from
being damaged.
Hints for optimum use
Sawing wood
Clamp the workpiece securely and remove all nails and
metal objects.
Holding the tool with both hands, work with the shoe (4)
pressed against the workpiece.
Flush cutting
The compact design of the reciprocating saw motor housing
and pivoting shoe permit close cutting to oors, corners and
other difcult areas.
To maximize ush cutting capabilities:
Insert the blade shaft into the blade clamp with the teeth
of the blade facing up.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FME360 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FME360 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info