720710
11
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
11
ENGLISH
(Original instructions)
u Rotate the stall release lever (6) on the tool to release the
driver blade and clear the jam. If tool is still jammed follow
the 9 steps listed below:
u Pull pusher downward until it locks in place then tip the
tool over so the nails slide freely out from the bottom of
the magazine.
u Lift the jam clearing latch (7) then pull up to open front
door (14).
u Remove bent nail, using pliers if necessary.
u If driver blade is in the down position, insert screwdriver
or other rod into nosepiece and push driver blade back
in position.
u Close the front door and engage the wire form (13)
under the two arms (15) on the contact trip. Push jam
clearing latch down (7) until it locks in place.
u Reinsert nails into magazine (see Loading the Tool).
u Pull pusher (10) downward until the nail follower (C1)
falls behind the nails as shown in gure C.
u Reinsert battery pack.
u Disengage trigger lock-off (2), allowing the trigger to be
actuated.
Warning!If a jam occurs, the tool will disable itself and will
require you to reset it. To do so, follow instructions on clearing
the jammed nail. Next remove battery pack and then reinsert
battery pack. The tool will now be operational.
Note!Should nails continue to jam frequently in contact trip,
have tool serviced by an authorized Stanley Fat Max service
center.
Cold Weather Operation
When operating tools at temperatures below freezing:
u Keep tool as warm as possible prior to use.
u Actuate the tool 5 or 6 times into scrap lumber before
using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct
sunlight as excessive heat can deteriorate bumpers and other
rubber parts resulting in increased maintenance.
Belt Hook (Fig. I-J)
Warning!Remove nails from magazine before making any
adjustments or servicing this tool. Failure to do so may result
in serious injury.
u Remove battery pack from tool, and engage trigger lock-
off.
u With a screwdriver remove screw from hang hook cavity
on the base of the tool (16).
u Place the front lip of the hang hook (11) into the cavity on
the base of the tool (16) as shown in Figure I.
u Secure the hang hook (11) with the supplied screw (17)
and rmly tighten with a screwdriver as shown in Figure J.
u Replace battery pack.
Replacement parts
Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
The tool comes equipped with a spare no mar tip located on
the side of the nail magazine.
u To replace the no mar pad, simply pull off the old no mar
pad and ret the new no mar pad onto the contact trip.
Use only identical replacement parts. For a parts list or to
order parts, visit our service website at www.stanley.eu/3co.
uk. You can also order parts from your nearest
Stanley Fat Max Factory Service Center or Stanley Fat Max
Authorized Warranty.
Troubleshooting
If your appliance seems not to operate properly, follow the
following instructions.
If this does not solve the problem, please contact your local
Stanley Fat Max repair agent.
Warning! Before proceeding, unplug the appliance.
Problem Possible Cause Possible Solution
Unit will not start. Battery pack not
installed properly.
Battery pack not
charged.
Trigger lock-off is
engaged.
Check battery pack
installation.
Check battery pack charging
requirements.
Disengage trigger lock-off.
Tool doesn’t
actuate.
(Headlights on,
motor does not
run)
Motor stops running
after 2 seconds.
Normal operation; release
trigger or contact trip and
re-depress.
Tool doesn’t
actuate.
(Headlights
ash)
Low battery charge or
damaged battery.
Charge or replace battery.
Tool doesn’t
actuate.
(Headlights ash
continuously)
Jammed fastener / tool
stalled.
Jammed mechanism
Remove the battery, rotate the
stall release lever. Clear the
jammed fastener, and reinsert
battery pack.
See authorized service center.
Tool doesn’t
actuate.
((Headlights on,
motor runs,
driver blade
stuck down)
See authorized service center.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FMC792 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FMC792 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info