622595
9
Verklein
Vergroot
Pagina terug
1/172
Pagina verder
9
ENGLISH
(Original instructions)
Accessories
The tool is supplied with a guard intended for grinding pur-
poses only. If the unit is intended to perform cutting off opera-
tions, a guard (24, Fig H) specic for this operation must be
tted. A suitable guard for cutting off operations part number
1004683-29 is available and can be obtained from Stanley
Fat Max service centres. Further information for guard types
and accessories is available in the Grinding and cutting chart
which can be found at the back of this language section.
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the guard (g. B)
The tool is supplied with a guard intended for grinding pur-
poses only. If the unit is intended to perform cutting off opera-
tions, a guard (24, Fig H) specic for this operation must be
tted. A suitable guard for cutting off operations part number
1004683-29 is available and can be obtained from Stanley Fat
Max service centres.
Fitting
u Place the tool on a table, with the spindle (11) facing up.
u Release the clamping lock (12) and hold the guard (5)
over the tool as shown.
u Align the lugs (13) with the notches (14).
u Press the guard down and rotate it counterclockwise to
the required position.
u Fasten the clamping lock (12) to secure the guard to the
tool.
u If required, tighten the screw (15) to increase the clamping
force.
Removing
u Release the clamping lock (12).
u Rotate the guard clockwise to align the lugs (13) with the
notches (14).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
u Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding discs, cutting discs
or sanding ap pads (g. C - E)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
u Fit the guard as described above.
u Place the inner ange (16) onto the spindle (11) as shown
(g. C). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the disc (17) onto the spindle (11) as shown (g.
C). If the disc has a raised centre (18), make sure that the
raised centre faces the inner ange.
u Make sure that the disc locates correctly on the inner
ange.
u Place the outer ange (19) onto the spindle. When tting
a grinding disc, the raised centre on the outer ange must
face towards the disc (A in g. D). When tting a cutting
disc, the raised centre on the outer ange must face away
from the disc (B in g. D).
u Keep the spindle lock (4) depressed and tighten the outer
ange using the two-pin spanner (8) (g. E).
Removing
u Keep the spindle lock (4) depressed and loosen the outer
ange (19) using the two-pin spanner (8) (g. D).
u Remove the outer ange (19) and the disc (17).
Fitting and removing sanding backing pads (g. E
& F)
For sanding, a backing pad is required. The backing pad is
available from your Stanley Fat Max dealer as an accessory.
Fitting
u Place the inner ange (16) onto the spindle (11) as shown
(g. F). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the backing pad (20) onto the spindle.
u Place the sanding disc (21) onto the backing pad.
u Place the outer sanding ange (22) onto the spindle with
the raised centre facing towards the disc.
u Keep the spindle lock (4) depressed and tighten the outer
ange using the two-pin spanner (8) (g. E). Make sure
that the outer ange is tted correctly and that the disc is
clamped tightly.
Removing
u Keep the spindle lock (4) depressed and loosen the outer
ange (19) using the two-pin spanner (8) (g. E).
u Remove the outer ange (19), the sanding disc (21) and
the backing pad (20).
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FMC761 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FMC761 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 19,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info