622614
6
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
6
ENGLISH
(Original instructions)
Fitting and removing a screwdriver bit or
socket(g. C)
This tool is tted with a quick release chuck to allow for an
easy exchange of bits.
Warning! Make certain the tool is locked to prevent switch
actuation before installing or removing accessories.
u Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u Pull and hold the chuck collar (4) away from the front of
the tool.
u Insert the bit shaft (12) into the chuck (3).
u Release the collar. The accessory is locked in place.
Note! To remove the bit/socket repeat the above steps.
Warning! Use only impact sockets. Non-impact sockets may
break and cause a hazardous condition. Inspect sock et prior
to use to ensure that it con tains no cracks.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (g. A)
The battery needs to be charged before rst use and whenev-
er it fails to produce sufcient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u To charge the battery (5), insert it into the charger (9).
The battery will only t into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
The charging indicator (10) will ash green continuously
(slowly).
The charge is complete when the charging indicator (10)
lights green continuously. The charger and the battery can be
left connected indenitely with the LED illuminated. The LED
will change to ashing green (charging) state as the charger
occasionally tops up the battery charge. The charging indica-
tor (10) will be lit as long as the battery is connected to the
plugged-in charger.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator (10) will ash red at a fast rate. Proceed as
follows:
u Re-insert the battery (5).
u If the charging indicators continues ashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
service centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
ash at each speed and repeat.
Selecting the direction of rotation (g. D)
For tightening, use forward (clockwise) rotation. For loosening,
use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(2) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
u To lock the tool, set the forward/reverse slider into the
centre position.
Screwdriving / nut setting
u Select the appropriate bit / socket for the screw or nut to
be driven.
u Select forward or reverse rotation as described above.
u Hold the tool in line with the fastener.
u After tightening, check torque with a torque wrench.
LED work light
The LED work light (7) is activated automatically when the trig-
ger is depressed. The LED work light will illuminate when the
trigger is partially depressed, before the unit begins running.
Hints for optimum use
Screwdriving
u Always use the correct type and size of screwdriver bit.
u If screws are difcult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stanley FMC640 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stanley FMC640 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info