603493
35
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
Radar Operation Manual Page 37
5. TROUBLESHOOTING
5.0 The Radar page is not available
Configure the I/O setup. Enter the I/O Connections menu, see procedure at Par. 2.7 and
select the Radar on the serial port to which the Radar is connected.
5.1 The message "Turn Radar On" is displayed on the Radar window
· Check the Radar On/Off switch. It is in the off position or has not been wired.
· Verify that the correct serial port is set in the I/O Connections menu, in case try setting
the Radar on another serial port (following procedure shown at Par. 2.7).
· Check that the Radar is connected to the chart plotter, to the same serial port as set
in the I/O Connections menu, in case try connecting it to another serial port.
· Verify that all the connections in the Junction box are done properly.
· Verify using a Voltage Meter that the Radar power supply level at the Junction Box is
at least 12V. The Radar is able to operate with 10V but some volts may be dropped due
to the cable length.
If everything above is correct, try shortening the green and the blue cable coming from the
Radar. If the Radar still doesn’t work you need to call the Standard Horizon Marine Product
support for assistance at (800)767-2450 for assistance.
5.2 After the Radar On/Off Switch is turned on the “Radar warming up”
window counts down but restarts counting down over and over.
The power supply level is too low. This may be caused by battery low, cable too long, cable
section to narrow.
5.3 Too much clutter near the Radar screen center
This is a typical phenomenon with Radar. Echoes from nearby vessel may hit other objects
like other vessels or other objects randomly and reflections can be received by Radar
antenna due to very short distance between the objects. This is normal condition in a port
where nearby targets (such as sailboat masts) may cause multiple reflections. In this case,
increase the SEA clutter and decreasing the GAIN.
If during navigation in open sea the center of the screen is covered by a large spot. If this
happens it means the most probably the Transmission Trigger Delay and/or the Main Bang
Suppression need to be correctly tuned (refer to Par. 3.1).
5.4 The screen center is always covered by a spot
The Transmission Trigger Delay or the Main Bang Suppression needs to be tuned (refer
to Par. 3.1).
5.5 After turning transmission On, the Radar page remains completely black
The Radar is probably not properly tuned. Execute the Automatic Tuning procedure to
restore optimal performance (refer to Par. 3.1).
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Standard Horizon CP300i bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Standard Horizon CP300i in de taal/talen: Engels als bijlage per email.

De handleiding is 2,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info