Handleiding Spidem divina de luxe (pagina 16 van 61) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans)

361824

Verklein

Vergroot

Pagina terug

1/61

Pagina verder

ENGLISHENGLISH

• 30 • • 31 •

Scalding hazard!

Splashing may occur at the start –

scalding hazard! The hot water nozzle and

pipe can reach high temperatures: avoid

touching directly with your hands.

• Before dispensing steam, wait for the green

temperature-ready LEDS (23 and 24) to light

up in a fixed way. The machine is immediately

ready for dispensing steam.

• Direct the steam nozzle (14) towards the drip

tray and turn the “hot water/steam” knob (16)

for a few seconds so that any residual water

comes out of the steam nozzle.

Continue until only steam is dispensed.

• Turn the knob (16) to OFF.

• Fill 1/3 of the vessel that you wish to use to

make cappuccino with cold milk.

For best results when making

cappuccinos, the milk and the used

cup should be cold.

• Immerse the steam nozzle into the milk to be

frothed and turn the knob (16); turn the

container slowly with up-down movements to

make uniform frothing (Fig.17).

• After using the steam for the desired time, shut

off the steam (16).

• The same system can be used to heat other

beverages.

• Clean the steam nozzle with a damp cloth

(Fig.18)

10 CLEANING AND MAINTE-

NANCE

General Cleaning

• Maintenance and cleaning should only be

carried out when the appliance is cold and

disconnected from the power supply.

• Do not immerse the appliance in water and

do not wash the parts in the dishwasher.

• Do not use abrasives or aggressive chemicals

(solvents) for cleaning.

• Do not dry the machine and/or any of its

parts using a microwave and/or conventional

oven.

• We recommend you clean the water tank and

change the water daily.

• Clean the ground coffee doser daily.

- Use the supplied brush to clean the doser

(Fig.19).

• To clean the appliance, use a soft cloth

dampened with water.

•Clean the service area and the coffee

dispenser.

• We recommend you empty and clean the

drip tray (12) and the coffee grounds

drawer (10) daily; to carry out this

operation you must open the front cover

(Fig.20) and remove the drip tray (Fig.21);

then, you can empty and clean all the

components.

• You can remove the coffee dispenser in order

to clean it (Fig.24):

- lower the dispensing unit nozzles

- take the dispensing unit as shown in Fig.24,

and remove it from its housing

- wash the whole unit with warm water.

10.1 The coffee disperser

The coffee dispenser (17) must be

cleaned each time you fill the

coffee bean container or, anyhow, at least

once a week.

• Switch off the appliance by pressing the ON/

OFF switch (7) to the “O” position and remove

the plug from the wall outlet.

• Open the service cover (15).

Remove the drip tray (12) and the coffee

grounds drawer.

• Remove the coffee dispenser by holding it

by its handle and pressing the “PUSH”

button (Fig.22)

• Make sure that the two steel filters are free

from any coffee residues.

The top filter can be removed by unscrewing

the plastic pin anticlockwise using the specific

supplied key (Fig.23.).

• Wash the coffee dispenser only with hot water:

do not use detergents.

Then accurately wash and dry all its

components.

• Refit the filter and carefully screw the plastic

pin back on using the specific key.

•Clean the compartment inside the

appliance.

• Holding it by its handle, insert the coffee

dispenser into its housing until it snaps into

place.

• Insert the coffee grounds drawer, the drip tray

plate and the drip tray.

• Close the cover (15).

11 DESCALING

Scaling occurs naturally when the appliance is

used.

Approximately every 3-4 months you should

descale it; it is ready for descaling when you

notice a reduction in the water flow or when the

LED of the button (26) flashes.

If you wish to carry this out at

home, you can use a descaling

product for coffee makers that is non toxic

and/or not harmful and commonly

available on the market.

Caution! Never use vinegar.

To descale the appliance proceed as follows:

• Mix the descaler with water as specified on

the package and fill the water tank.

• Switch ON the appliance with the ON/OFF

switch (7).

• Press the button (26) for at least 5 seconds to

select the descaling operating mode; the LED

emits a fixed light.

• Direct the steam nozzle (14) toward the drip

tray.

• Position a vessel of adequate capacity under

the steam nozzle and turn the hot water knob

anticlockwise (16).

The appliance starts an automatic

descaling cycle with pauses preset by the

manufacturer and managed automatically

by the appliance.

• At the end of the cycle, the flow of the

descaling solution is shut off and the 5 buttons

start flashing simultaneously.

• Turn the knob of the hot water nozzle (16)

clockwise to OFF. In this case, also the warning

light (27) flashes.

• Rinse the water tank and fill it with fresh

drinking water.

• Position a vessel of adequate capacity

under the steam nozzle and empty 2/3

of the contents of the water tank by

turning the steam knob (16)

anticlockwise; to shut off the flow, turn

the knob (16) clockwise.

• Let the appliance heat up and empty the

remaining contents of the water tank by

turning the steam knob (16)

anticlockwise; to stop the flow, turn it

clockwise.

If you use a different product from

the recommended one, we

recommend you follow the instructions of

the descaler manufacturer as specified on

the package.

If the descaling cycle is interrupted

by switching the machine OFF, this

is restarted when the machine is switched

back ON.

12 FUNCTION PROGRAMMING

The appliance allows you to programme some

parameters depending on your needs.

To programme the functions, you must enter

programming mode as follows:

• Ensure that the ON/OFF switch (7) of the

appliance is switched to “O” and that the hot

water knob (16) is OFF.

• Press the buttons (23) and (25) and, at the

same time, switch ON the appliance using

the ON/OFF switch (7).

You are now in the programming mode.

To quit the programming mode and

implement your changes, switch the machine

OFF and, then, back ON again using the

main switch (7).

12.1Programming water hardness

Running water is more or less hard, depending

on the area.

This coffee maker can be adjusted so that it

will work optimally with the water hardness

level, expressed on a scale from 1 to 4, of

Spidem divina de luxe Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info