Handleiding Spektrum DX18 - SPM18000 (pagina 26 van 42) (Engels)

726853

Verklein

Vergroot

Pagina terug

1/42

Pagina verder

26 SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL

Sequencer

The Sequencer menu option provides this-then-that mixing with

a time delay. Five different sequences (S1 through S5) are avail-

able to control 2 functions each (A and B), in 2 timing directions

(forward or reverse). Sequences appear throughout function

screens as assignable switches.

CAUTION: Always review the action of a sequence on

the Monitor or X-Plus Monitor screen BEFORE operating

the model to ensure controls act as desired. Failure to do so

could cause a crash, resulting in property damage and or injury.

You can program multiple functions to sequentially activate

in response to an assigned switch. For example, an assigned

Gear switch can open gear doors, lower the gear, then close the

doors. In reverse, gear doors open, the gear retracts and the

gear doors close.

You can assign each Sequencer function to a switch in most

Function screens such as Flight Mode, Dual Rate, Mixing,

Throttle Curve, Pitch Curve, etc.

You can assign several functions to a sequence to decrease

the number of controls you need to touch during complex ﬂ ight

transitions, for example, applying your assigned dual rates and

exponential when the landing gear deploys and the ﬂ ight mode

changes.

If you select an S-Number-A sequence, for example, S3A, the

sequence operates as a timed 5-position switch. An S-Number-

B sequence operates as a timed 3-position switch. The 5

positions correspond to the sequencer values shown on the

time delay graph in the second Sequencer screen. In a function

screen, highlight each point (0-4) and select the switch position

desired for a function to be active.

When S1B (or another sequence-number-B) is selected as

a switch in a function, the sequence will operate as a timed

3-position switch. The 3 positions act as ‘kick points’ of the

movement at ﬁ xed percentages (equal thirds) of the sequencer

output. In a function screen, highlight each point (0-2) and select

the switch position desired for a function to be active.

Sequencer Set Up

1. In the ﬁ rst Sequencer screen, select 1 of the 5 available

sequences.

2. In the second Sequencer screen, assign a switch to the

sequence. We recommend using a 2-position switch.

Tip: If you need to use a 3-position switch, you must assign

one direction to two adjacent switch positions, for example,

0 and 1. Assign the opposite direction to the third switch

position.

3. Assign the timing for the Forward and Reverse directions as

desired. There is no delay when you use the Nor option. You

may also select a delay time between 0 and 30 seconds.

4. Assign names for each sequencer function, as desired.

5. Select either Step (S) or Proportional (P) for the Sequencer

output.Step: The sequence only changes at kick points.

Otherwise, there is a delay in the sequence until it reaches

the next kick point.

Proportional: The sequence movement is proportional

between kick points. The sequence maintains rate and

direction until it reaches the next kick point.

6. Adjust the Sequencer motion percentages in the third screen.

For example, you may move points 1, 2 and 3 closer to the

beginning of the sequence so the motion occurs earlier. This

results in a delay between point 3 and point 4 at the end of the

sequence.

Testing the Sequence

The Sequencer function determines the response for channels

included in the sequence.

Refer to the Monitor screen to see how respective channels

interact in the Sequencer.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Spektrum DX18 - SPM18000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Spektrum DX18 - SPM18000

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info