583074
6
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
4
HAG 2000 • HAG 2000E • HAG 2000ED
EN
WARNING: Do not place your hand over the
air vents (3) at the machine rear or block the vents in
any way.
Stay alert, watch what you are doing and use common
sense when operating a appliance. Do not use a ap-
pliance while you are tired.
Take a secure stance; do not overreach, especially on
ladders and stages.
To use this appliance properly, you must observe
the safety regulations, the assembly and operating
instructions in this booklet. All persons who use and
service the machine have to be acquainted with this
Manual and must be informed about the potential haz-
ards when operating this appliance.
This machine is not intended for use by persons (in-
cluding children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or in-
struction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
The appliance must not be used outdoors in rainy
weather, or in moist environment (after rain) or in close
vicinity with easily flammable liquids and gases. The
working place should be well lit.
Know your product
Before using the appliance, familiarize yourself with all
the operating features and safety requirements.
Use the appliance and accessories only for the applica-
tions intended. All other applications are expressly ruled
out.
1. Nozzle
2. Heat protector
3. Ventilation slots
4. Rubber soft stand
5. Temperature control buttons (HAG 2000ED)
5a. Temperature regulator (HAG 2000E)
6. ON/OFF switch
7. LCD display (HAG 2000ED)
8. Reduction nozzle
9. Glass protection nozzle
10. Reector nozzle
11. Flat nozzle
12. Triangular scraper
Operation instructions
This appliance is supplied from single-phase alternat-
ing current mains only. It is double insulated according
to EN 60335-1 and can be connected to grounded or
not grounded sockets. This appliance is radio sup-
pressed in compliance with EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3 for radio interference.
This appliance is intended for the removal of paint, form-
ing and welding of plastic, warming of heat-shrinkable
tubing; the tool is also suitable for soldering, loosening
adhesive joints and defrosting water pipes.
PRIOR TO INITIAL OPERATION
Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
data of the tool.
Always check the position of ON/OFF switch. The ap-
pliance must be connected to the power supply socket
only when this switch is in OFF position as the maxi-
mum temperature is achieved for 60 seconds only.
Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
WARNING: Always switch off and unplug the
appliance prior to any adjustment or maintenance.
Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a quali-
fied person; never attempt to open the tool yourself.
The distance between the nozzle and the processed
material will vary depending on the kind of material
but regardless of the regulator position keep the air
outlet at least at 50 mm away from the processed
surface.
All application examples (except removing paint from
windows) can be performed without accessories;
however, using the appropriate accessory facilitates
operation and significantly improves the quality of the
results.
SWITCHING ON - SWITCHING OFF
The hot air gun can be switched on and off by means of
the 3-stage ON/OFF switch (6) at the rear of the handle.
Switching on: Set the switch (6) to position I. Some
smoke may be emitted after switching on; this does not
indicate a problem.
Switching off: Set the switch (6) to position O. Let the
machine cool down with the nozzle up before leaving it
down or storing it.
The air ow can be adjusted by setting the switch lever
(6) to position I, II or III.
Set the switch (6) to position I in order to protect the sur-
rounding surfaces from overheating or in case the work-
piece is lightweight and there is danger of being swept
away by the air ow.
pages-HAG 2000[ED]-2014.indd 4 25.4.2014 г. 10:31:48 ч.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sparky HAG 2000ED bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sparky HAG 2000ED in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 3,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info