604122
9
Verklein
Vergroot
Pagina terug
1/110
Pagina verder
7
Original instructions
EN
breaking and chiselling in brickwork, concrete
and rocks with high efciency. In impact drilling
mode the rotary hammer equipped with adapter
and chuck 176838 (not included) can be used
as a drill for drilling in steel, wood, plastics, etc.
Power tools marked with this symbol
are equipped with a mechanism for reducing vi-
brations, decreasing them by more than 50%.
PRIOR TO INITIAL OPERATION
Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
Make sure that the cord and the plug are in or-
der. If the replacement of the supply cord is nec-
essary, this has to be done by the manufacturer
or his agent in order to avoid a safety hazard.
In case the work area is remote from the power
source, use as short as practicable extension
cord with proper cross-section.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
Check that the auxiliary handle is properly
mounted and reliably tightened.
SWITCHING ON - SWITCHING OFF
Brief activation
Switching on: Press ON/OFF switch 5. (Fig.1)
Switching off: Release ON/OFF switch 5.
Continuous operation
Switching on: Press ON/OFF switch 5 and in
pressed position lock it by button 6. (Fig. 2)
Switching off: Press ON/OFF switch 5 once and
release it immediately.
At low temperatures, demolishing with the pow-
er tool must begin only after it was operated for
about 3 minutes at no-load mode.
INSERTING OF SDS-Plus TOOL
Clean and grease the shank of the accessory,
before placing it into the socket! (Fig.3)
Pull backward the sleeve 3 of the socket 1
(Fig. 4a) and insert the SDS-Plus bit until stop.
Ensure that the socket grooves correspond to
the shank channels, and then release the sleeve
to x the bit. (Fig. 4b)
To remove the bit, pull the sleeve 3 back, and
then take the bit out. (Fig.5)
WARNING: Never use drill bits with
diameter exceeding the indicated to avoid
overloading the power tool..
SELECTINGTHESPEED,FREQUENCY
AND IMPACT ENERGY
Rotate the regulator 7 to choose a position ap-
propriate for the processed material. It is recom-
mended to use the operation modes listed in the
table.
Application
Regulator
position
Rotation
speed
Impactrate Impactenergy
Boring with core cutters A-D 380-650 min
-1
1560-2660 min
-1
1.5-3.6 J
Render / Light construction
materials / Bricks / Chiselling
tiles
D-Е 650-740 min
-1
2660-3030 min
-1
3.6-4.3 J
Chiselling and drilling concrete
F 830 min
-1
3400 min
-1
5 J
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sparky BP 330E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sparky BP 330E in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 1,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info