611473
15
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
13Soundcraft MFXi MPMi User Guide Issue 1210
this to monitor the post-EQ signal from the channel.
12 MIX/SUB SWITCH When this switch is up, the channel’s post-pan-pot signal is routed to the Mix (left
and right) buses. When the switch is depressed, the post-pan-pot signal is routed
to the Sub-group (left and right) buses.
13 PEAK LED This is used to indicate that the signal is close to distorting (clipping) on a specic
channel.
14 SP LED The SP LED glows when a signal is present. The feed point for the LED is post-insert,
pre-EQ.
15 INPUT CHANNEL FADER This is used to control the level fed to the Mix Bus and post-fade sends.
16 MIX OUTPUTS (XLR) Connect these to your analogue recording device, or to your amplication system.
& MONO OUT (¼ Jack)
17 SUB-GROUP OUTPUTS These outputs can be connected to a separate amplier system or to an external
(¼ Jack) processor.
18 SUB-GROUP ROUTING The sub-group mix can be routed to the main mix, in mono or stereo.
19 MASTER FADERS These faders control the overall level of the mix and sub-group outputs.
20 MAIN METERS These show the level of the mix outputs. When the master SOLO LED is lit, the meters
show the level of the selected AFL/PFL signal.
21 MONITOR OUTPUTS These are used to feed your monitoring system. This can be directly connected to
(¼ Jack) powered monitors, or indirectly via an amplier to standard monitors.
22 MONITOR CONTROL This controls the level of the signal sent to your monitoring system.
23 MONITOR SELECT SWITCH This switch selects the signal source to be monitored. Note that the 2-TK input can
be monitored also, see item 31 below.
24 PHONES CONTROL This controls the level of the signal sent to the headphones jack socket.
25 HEADPHONES (¼ Jack) Plug your headphones into this socket. Recommended headphones impedance is
32 ohms or greater.
26 AUX 1 & 2 OUTPUTS
These outputs can be used to send the channel signal to an artist’s monitors (head
(¼ Jacks)
phones/in-ear/stage monitors), external FX or secondary PA/monitor system.
27 AUX CONTROLS The rotary controls set the output levels of the two Aux Outputs. The After Fade
& AFL SWITCHES (AFL) Listen switches route their respective aux output signal to the monitor/
headphones outputs.
28 AUX 2 POST/PRE SWITCH This switch globally changes the AUX 2 feed on all the input modules to be either
post-fade or pre-fade.
29 STEREO INPUTS (¼ Jack) These two pairs of inputs can be used to connect line level stereo inputs from key-
boards, sound modules, samplers, computer based audio cards etc. These inputs
pass through a stereo channel strip, with EQ, Auxes and a Balance control. Mono
sources may be used by plugging into the left jack only.
30 2-TRACK IN
(RCA Phono)
You can connect the playback from your recording device here.
31 2-TRACK OUT Use these to control the 2 Track signal. The MONITOR switch sends the signal to the
monitor outputs and phones, whilst the TO MIX switch sends it to the main mix.
32 RECORD OUTPUTS
(RCA Phono)
You can connect these to the inputs of your recording device.
33 PHANTOM POWER Press this to globally switch the phantom power (48V) on for condenser microphones.
WARNING: Do Not apply Phantom Power before
connecting a microphone.
34 STEREO RETURN INPUTS This pair of inputs accept 3-pole A gauge (TRS) jacks. Use these inputs for sources
such as keyboards, drum machines, synths or CDs. The inputs are BALANCED. Mono
sources may be used by plugging into the left jack only.
35 STEREO RETURN CONTROL This control sets the level of signal routed to the main mix busses.
36 FX BUS OUTPUT This output carries the signal from the FX bus. It could be used as a third Aux Output
if desired if the FX Processor is not needed at the time. The FX sends on the inputs
channels to the FX bus are always post-fade.
37 FX CONTROL & AFL SWITCH The rotary control regulates the signal level being fed from the FX bus to the FX
processor and to the FX BUS OUTPUT socket. The After-Fade Listen (AFL) switch
routes this post-FX-control, pre-FX signal to the monitor/headphones outputs.
38 FOOTSWITCH CONNECTOR This is used by the FX Processor, see page 33.
39 LEXICON® FX PROCESSOR See the information starting on page 33 .
15

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Soundcraft-MFXi

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Soundcraft MFXi bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Soundcraft MFXi in de taal/talen: Engels als bijlage per email.

De handleiding is 2,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Soundcraft MFXi

Soundcraft MFXi Gebruiksaanwijzing - Deutsch - 47 pagina's

Soundcraft MFXi Gebruiksaanwijzing - Français - 56 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info