812372
17
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
Tmin S1
Enable/start temperature at sensor 1:
If this value on the sensor 1 (collector sensor) is exceeded and the other conditions are not fulfilled, the controller will turn on the affiliated
pump or the valve. If the temperature on the sensor 1 falls 5 °C below this value, the pump or the valve will be turned off again.
Tmin S2
Switch off temperature at sensor 2:
If this value is exceeded on the sensor 2, the controller turn off the affiliated pump or the valve. If this value on the sensor 2 is undershot and
the other conditions are fulfilled, the controller will turn on the pump or the valve.
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be provided
by the customer!
In multiple storage systems, if the shut-down temperature S2 is exceeded, a downstream installed storage or storage area is switched to.
ΔT R1
On/off temperature difference for solar charge through relay R1:
If the temperature difference ΔT Solar between the reference sensors S1 and S2 is exceeded and the other conditions are fulfilled, the con-
troller will turn on the pump on the relay R1. If the temperature difference falls to ΔT Off, the pump will be turned off.
If the set temperature difference is too small, this may lead to ineffective operation depending on the system and sensor pos-
itioning. For speed regulation (" Speed control " on page 20), special switch conditions apply!
Tset On
Reference temperature sensor 1
Heating mode = 1. Value smaller than 2. value,
Cooling mod = 1. Value bigger than 2. value.
If the set switch-on value (1. Value) at sensor 1 undershot and thermostat function is approved (see also 5.5), backup heating is switched
on until temperature exceeds value for switch off (2. Value).
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be provided
by the customer!
If sensor S2 is connected, S1 functions as a switch-on sensor and S2 as a switch-off sensor.
Tmax S1
Switch off temperature at sensor 1
If this value is exceeded on the sensor 1, the controller turn off the affiliated pump or the valve. If sensor 1 falls below this value again and
the other conditions are also met, then the controller switches the pump and/or valve on again.
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be provided
by the customer!
Thermostat periods
Here the desired periods are set in which the thermostat function is approved. For each weekday, three times can be specified, fur-
thermore, you can copy individual day to other days. The thermostat function is shut down outside of the set times.
Tmin Storage X
Switch off temperature at sensor S(X)
If this value is exceeded at sensor X then the controller switches the associated pump and/or valve off. If sensor (X) falls below this value
again and the other conditions are also met, then the controller switches the pump and/or valve on again.
17
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sorel STDC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sorel STDC in de taal/talen: Engels als bijlage per email.

De handleiding is 2.95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sorel STDC

Sorel STDC Gebruiksaanwijzing - Nederlands - 48 pagina's

Sorel STDC Gebruiksaanwijzing - Deutsch - 26 pagina's

Sorel STDC Gebruiksaanwijzing - Français - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info