812394
18
Verklein
Vergroot
Pagina terug
1/23
Pagina verder
Delay
Switch delay, valid for cooling and heat request. The burner first turns on after this time span if the switch conditions were reached and are
still present. This feature prevents unnecessary switching by temperature fluctuations or gives time for a renewable energy source to gen-
erate energy.
Relay mode
Switching: Request is made via signal output V1.
Output signal to V1: "no request" = 0V, "request" = 10V
Modulating: Request is made via signal output V1. The SLC Plus outputs the requested temperature (calculated target VL) as a voltage
via the signal output.
Example: Calculated target VL heating circuit 43 ° C, measured VL at sensor S2 40 ° C.
If the VL sensor exceeds the setpoint VL by 2K (preferece/actual -) for more than 2 minutes, the SLC Plus requests a heat source with 4.3V
(corresponds to 43 ° C setpoint VL).
The requested temperature can be raised with the value "Offset". 0.1 V correspond to 1 ° C. If you set an offset of 0.5 V, this results in a
requested temperature of 48 ° C or 4.8 V (43 ° C corresponds to 4.3 V + 0.5 V (offset) = 4.8 V corresponds to 48 ° C)
Burner offset
When using the 0-10V outputs V1 for the burner function, the requested temperature is emitted through a corresponding voltage. This off-
set increases the requested temperature.
Parallel operation V1/V2
Switches the selected relay in parallel with the 0-10 V / PMW output V1/V2.
Switch parallel operation on, off or inverted.
Parallel operation
Here you can additionally set the switch mode.
On : The function switches parallel to the set signal output.
Inverted : The function switches contrary to the set signal output.
Delay
The assigned relay switches on the delay set here later than V1/V2.
Follow-up time
The assigned relay switched on for the time set here longer than V1/V2.
Always on
Relay is permanently switched on.
Signal V1/V2
The signal output V1 is factory-set for the burner request by 0-10V. Alternatively, the error message can also be selected and activated in
the menu. Signal V2: The signal output V2 can be used to control a circulation pump or for error messages. To activate one of these func-
tions, the corresponding menu item must be selected. The signal outputs V1/V2 (0-10V) can be used to switch higher voltages in con-
junction with a potential-free relay (optional accessory). Only one function can be selected per signal output.
Pressure Monitoring
In this menu, the system pressure monitoring can be activated through a direct sensor. Once the set pressure conditions are exceeded, a
message is generated and the LED flashes red.
Pressure Monitoring
A message is displayed and the LED flashes red when the pressure drops below minimum or exceeds the maximum.
Pmin
Minimum pressure. If this pressure is not met, the controller emits an error notification and the red LED flashes.
18
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sorel SLC Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sorel SLC Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 0.71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sorel SLC Plus

Sorel SLC Plus Gebruiksaanwijzing - Deutsch - 23 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info