812334
14
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
RC21 Room thermostat with remote control
The RC21 room thermostat is an optional accessory and is normally not included in the scope of supply.
The remote control with integrated thermostat RC21 provides you with easy to use temperature controlled adjustment of the temperature
from within your living space.
Setting options
The RC21 control dial parallel shifts the heating circuit characteristic stored in the controller. The flow temperature (depending the out-
door temperature) is increased or decreased respectively by this. When the dial is turned all the way down, the heat circuit is switched
off. Frost protection stays active to prevent damage.
Temperature Sensors
The RC21 room thermostat has a built-in temperature sensor, the values of which are registered, used and displayed in the controller. If
the settings in the controller allow it, the sensor is used to alter the flow temperature.
Operating Modes
The slider can be moved to the following operating modes.
In automatic mode, the temperature is controlled according to the set thermostat periods.
In continuous day mode, the set times are ignored and the temperature is controlled according to the day settings.
In continuous night mode, the temperature is usually reduced. This setting is suitable, for example, for periods of prolonged
absence (e.g. holidays).
Installation
Carefully remove the dial from the housing with a screwdriver.
Loosen the screw beneath. Remove the light-coloured part of the
housing from the base.
The RC21 is connected to the controller via 3 wires.
1) Remote control -> to a free sensor input (S1 - S4)
2) Temperature sensor -> to a free sensor input (S1 - S4)
3) GND
The following picture shows exemplary wiring.
The setup of the room controller is done in the following menu:
7. Special functions -> 7.5. Room controller
7.5.5. Thermostat
select "RC21-Local 1".
7.5.13. RC-local:1 Type
Select here the sensor input that you use for the temperature sensor (Terminal 1) of the RC21.
„7.5.2. Room ref. day“ / „7.5.3. Room ref. night“
Setting the desired room temperature for day/night operation.
7.5.1. Room Controller
This value is used to appoint the amount of influence the room temperature has on the reference flow temperature, as a percentage. For
each degree deviation between room temperature and reference temperature, the percentage of the calculated set flow temperature set
here is added to the set flow temperature or subtracted from it up to the min. or max. values set under the protective functions.
Example: Reference room temp.: 25 °C; room temp.: 20 °C = 5 °C deviation. Calculated reference flow temp.: 40 °C: room controller: 10
%= 4 °C 5 X 4 °C= 20 °C. Accordingly, 20 °C are added to the reference flow temperature, giving 60 °C. If the value is higher than the
one set in "Max. flow temp", the resulting temperature will be the one set in "Max. flow temp".
Under „7.5.6. Thermostat 2" further °CALEONs can be set optionally as room controllers. The same system as for the first room controller
applies.
5. Settings -> 5.11. Heating circuit off
If you want the heating circuit to switch off in addition to summer-winter shutdown, even if the room temperature is reached, set "summer
+ room" here.
The RC21 is suited for low voltage only!
14
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sorel MHCC 24V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sorel MHCC 24V in de taal/talen: Engels als bijlage per email.

De handleiding is 2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sorel MHCC 24V

Sorel MHCC 24V Gebruiksaanwijzing - Deutsch - 30 pagina's

Sorel MHCC 24V Gebruiksaanwijzing - Français - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info