135985
3
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
3-868-269-E1 (1)
Video Cassette
Recorder
Operating Instructions
SLV-SE600A/E
SLV-SX600E
SLV-SE650D
SLV-SE700D1/D2/E1/E2
SLV-SX700D/E
SLV-SE800D1/D2/E
SLV-SX800D
© 2000 Sony Corporation
PAL NTSC4.43
2
WARNING
WARNING
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Mains lead must only be changed at a qualified
service shop.
Precautions
Safety
This unit operates on 220 – 240 V AC, 50 Hz.
Check that the unit’s operating voltage is
identical with your local power supply.
If anything falls into the cabinet, unplug the unit
and have it checked by qualified personnel before
operating it any further.
The unit is not disconnected from the mains as
long as it is connected to the mains, even if the
unit itself has been turned off.
Unplug the unit from the wall outlet if you do not
intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never
by the cord.
Installing
Allow adequate air circulation to prevent internal
heat buildup.
Do not place the unit on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that
may block the ventilation slots.
Do not install the unit near heat sources such as
radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical
vibration or shock.
Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position
only.
Keep the unit and cassettes away from equipment
with strong magnets, such as microwave ovens or
large loudspeakers.
Do not place heavy objects on the unit.
If the unit is brought directly from a cold to a
warm location, moisture may condense inside the
VCR and cause damage to the video head and
tape. When you first install the unit, or when you
move it from a cold to a warm location, wait for
about three hours before operating the unit.
Caution
Television programmes, films, video tapes and other
materials may be copyrighted. Unauthorized
recording of such material may be contrary to the
provisions of the copyright laws. Also, use of this
recorder with cable television transmission may
require authorization from the cable television
transmitter and/or programme owner.
Compatible colour systems
This VCR is designed to record using the PAL (B/
G) colour system and play back using the PAL (B/
G) and NTSC 4.43 colour systems. Recording of
video sources based on other colour systems cannot
be guaranteed.
S
HOWVIEW is a registered trademark of Gemstar
Development Corporation. The S
HOWVIEW system
is manufactured under license from Gemstar
Development Corporation.
3
Table of contents
Getting Started
Table of contents
Getting Started
4 Step 1 : Unpacking
5 Step 2 : Setting up the remote commander
9 Step 3 : Connecting the VCR
13 Step 4 : Tuning your TV to the VCR
16 Step 5 : Setting up the VCR with the Auto Set Up function
19 Step 6 : Setting the clock
24 Selecting a language
26 Presetting channels
30 Changing/disabling programme positions
36 Setting the PAY-TV/Canal Plus decoder
(not available on SLV-SE600A)
Basic Operations
41 Playing a tape
44 Recording TV programmes
48 Recording TV programmes using the
Dial Timer
(SLV-SE800D1/D2/E and SX800D
only)
53 Recording TV programmes using the
ShowView system
(not available on SLV-SE600A/E and
SX600E)
57 Recording TV programmes using the
timer
Additional Operations
61 Playing/searching at various speeds
64 Setting the recording duration time
65 Synchronized Recording
(SLV-SE800D1/D2/E and SX800D
only)
68 Checking/changing/cancelling timer
settings
70 Recording stereo and bilingual
programmes
72 Searching using the Smart Search
function
75 Searching using the index function
76 Adjusting the picture
78 Changing menu options
Editing
80 Connecting to a VCR or stereo
system
82 Basic editing
83 Audio dubbing
(SLV-SE800D1/D2/E and SX800D
only)
Additional Information
85 Troubleshooting
89 Specifications
90 Index to parts and controls
Back Cover
Index
4
Unpacking
Getting Started
Step 1 : Unpacking
Check that you have received the following items with the VCR:
Remote commander Aerial cable
R6 (size AA) batteries
Check your model name
The instructions in this manual are for the 14 models: SLV-SE600A, SE600E, SX600E,
SE650D, SE700D1, SE700D2, SE700E1, SE700E2, SX700D, SX700E, SE800D1,
SE800D2, SE800E, and SX800D. Check your model number by looking at the rear panel
of your VCR.
SLV-SE800E is the model used for illustration purposes. Any difference in operation is
clearly indicated in the text, for example, “SLV-SE700E1 only.”
Getting Started
5
Setting up the remote commander
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot () can be used to operate your
Sony TV. If the TV does not have
the symbol near the remote
sensor, this remote commander
will not operate the TV.
To operate Set [TV] / [VIDEO] to
the VCR [VIDEO] and point at the remote sensor at the VCR
a Sony TV [TV] and point at the remote sensor at the TV
123
456
789
0
Remote sensor
[TV] /
[VIDEO]
continued
6
Setting up the remote commander
TV control buttons
To Press
Set the TV to standby mode ?/1
Select an input source: aerial in or line in t TV/VIDEO
Select the TVs programme position Programme number buttons, -,
PROG +/–
PROG +/–/
c/C
2 +/–
123
456
789
0
Programme
number
buttons
WIDE
DISPLAY
?/1
t TV/VIDEO
-
AUDIO MONITOR
FASTEXT buttons
/
a
Getting Started
7
Setting up the remote commander
Notes
With normal use, the batteries should last about three to six months.
If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
Do not use a new battery together with an old one.
Do not use different types of batteries together.
Some buttons may not work with certain Sony TVs.
* not available on SLV-SE600A/E, SX600E, and SE650D
Controlling other TVs with the remote commander
(not available on SLV-SE600A/E, SX600E, and SE650D)
The remote commander is preprogrammed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer’s code number.
* These buttons may not work with all TVs.
Adjust the volume of the TV 2 +/–
Switch to TV (Teletext off)* a (TV)
Switch to Teletext* / (Teletext)
Select the sound AUDIO MONITOR
Use FASTEXT* FASTEXT buttons
Call up the on-screen display
DISPLAY
Change the Teletext page* c/C
Switch to/from wide mode of a Sony wide TV (For other
manufactures’ wide TVs, see “Controlling other TVs with
the remote commander (not available on SLV-SE600A/E,
SX600E, and SE650D)” below.)
WIDE
1
Set [TV] / [VIDEO] at the top of the remote commander to [TV].
2
Hold down ?/1, and enter your TV’s code number using the programme number
buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten’s digit), PROG +/–,
2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*,
M/m/</
,*, and OK*.
To Press
continued
8
Setting up the remote commander
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable code
numbers.
*
1
Press WIDE to switch the wide picture mode on or off.
*
2
Press WIDE, then press 2 +/– to select the wide picture mode you want.
*
3
Press WIDE. The menu appears on the TV screen. Then, press M/m/</, to select the
wide picture you want and press OK.
Tip
When you set your TV’s code number correctly while the TV is turned on, the TV turns off
automatically.
Notes
If you enter a new code number, the code number previously entered will be erased.
If the TV uses a different remote control system from the one programmed to work with the
VCR, you cannot control your TV with the remote commander.
When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
Manufacturer Code number
Sony
01*
1
, 02
Akai 68
Ferguson 52
Grundig
10*
1
, 11*
1
Hitachi 24
JVC 33
Loewe 45
Mivar 09, 70
NEC 66
Nokia
15, 16, 69*
3
Panasonic
17*
1
, 49
Philips
06*
1
, 07*
1
, 08*
1
Saba 12, 13
Samsung 22, 23
Sanyo 25
Sharp 29
Telefunken 36
Thomson
43*
2
Toshiba 38
Manufacturer Code number
Getting Started
9
Connecting the VCR
Step 3 : Connecting the VCR
If your TV has a Scart (EURO-AV) connector, see page 10.
If your TV does not have a Scart (EURO-AV) connector
Note
When you connect the VCR and your TV only with an aerial cable, you have to tune your TV
to the VCR (see page 13).
1
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on
the rear panel of the VCR.
2
Connect AERIAL OUT of the VCR
and the aerial input of your TV using
the supplied aerial cable.
3
Connect the mains lead to the mains.
Mains lead
AERIAL IN
to mains
Aerial cable (supplied)
AERIAL OUT
: Signal flow
AERIAL IN
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
IN
ENTREE
OUT
SORTIE
AERIAL
ANTENNE
continued
10
Connecting the VCR
If your TV has a Scart (EURO-AV) connector
Note
If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to OFF is
recommended. In the OFF position, only the signal from the aerial is output through the
AERIAL OUT connector (see page 15).
1
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on
the rear panel of the VCR.
2
Connect AERIAL OUT of the VCR
and the aerial input of your TV using
the supplied aerial cable.
3
Connect LINE-1 (TV) on the VCR
and the Scart (EURO-AV) connector
on the TV with the optional Scart
cable.
This connection improves picture and
sound quality. Whenever you want to
watch the VCR picture, press t TV/
VIDEO to display the VIDEO
indicator in the display window.
4
Connect the mains lead to the mains.
Mains lead
i LINE-1
(TV)
AERIAL IN
Scart
(EURO-AV)
to mains
Aerial cable (supplied)
AERIAL OUT
: Signal flow
Scart cable (not supplied)
AERIAL IN
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
IN
ENTREE
OUT
SORTIE
AERIAL
ANTENNE
Getting Started
11
Connecting the VCR
About the SMARTLINK features
(not available on SLV-SE600A/E and SX600E)
If the connected TV complies with
SMARTLINK, MEGALOGIC*
1
,
EASYLINK*
2
, Q-Link*
3
, EURO VIEW
LINK*
4
, or T-V LINK*
5
, this VCR
automatically runs the SMARTLINK
function after you complete the steps on the previous page (the SMARTLINK
indicator appears in the VCRs display window when you turn on the TV). You can
enjoy the following SMARTLINK features.
Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR
according to that data in Auto Set Up. This greatly simplifies the Auto Set Up
procedure. Be careful not to disconnect the cables or exit the Auto Set Up function
during the procedure.
See “Setting up the VCR with the Auto Set Up function” on page 16.
TV Direct Rec
You can easily record what you are watching on the TV. For details, see
“Recording what you are watching on the TV (TV Direct Rec) (not available on
SLV-SE600A/E and SX600E)” on page 47.
One Touch Play
With One Touch Play, you can start playback automatically without turning on the
TV. For details, see “Starting playback automatically with one button (One Touch
Play) (not available on SLV-SE600A/E and SX600E)” on page 43.
One Touch Menu
You can turn on the VCR and TV, set the TV to the video channel, and display the
VCR’s on-screen display automatically by pressing MENU on the remote
commander.
One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the
timer recording menu (the TIMER METHOD menu, the TIMER menu, or the
SHOWVIEW menu) automatically by pressing TIMER on the remote
commander.
You can set which timer recording menu is displayed using TIMER OPTIONS in
the OPTIONS-2 menu (see page 79).
Automatic Power Off
You can have the VCR turn off automatically, if the VCR is not used after you turn
off the TV.
*
1
“MEGALOGIC” is a registered trademark of Grundig Corporation.
*
2
“EASYLINK” is a trademark of Philips Corporation.
*
3
“Q-Link” is a trademark of Panasonic Corporation.
*
4
“EURO VIEW LINK” is a trademark of Toshiba Corporation.
*
5
“T-V LINK” is a trademark of JVC Corporation.
Note
Not all TVs respond to the functions above.
SMARTLINK
continued
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sony slv sx 800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sony slv sx 800 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Sony slv sx 800

Sony slv sx 800 Gebruiksaanwijzing - Nederlands - 96 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info