Handleiding Sony rm v 201 t (pagina 1 van 2) (Engels, Frans)

122367

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

To use this Remote Commander with a Sony brand component that

is already preset at the factory (see the table on the left), you can skip

this procedure.

If you are using other brand’s component or if you cannot operate

even a Sony brand component, follow this procedure.

Setting by Entering the Code Number

See the supplied “Component Code Numbers” and find the code for

your component.

1 Set the slide switch to the position that corresponds to the

component to set up.

To set up... Set the slide switch to...

a TV TV

a satellite tuner SAT

a VCR VCR or AUX

2 Press the S (set) button.

3 Enter the three-digit component code in the “Component

Code Numbers” table.

For example, to set a Philips’ TV, press .

4 Press the … button.

5 Aim this Commander to your component and check if you can

operate it using this Commander.

Go through the same procedure for each component you want to set

up.

If you cannot operate your component...

•First, try repeating these set up procedures using the other codes

listed for your component (see “Component Code Numbers”).

•If — after trying all the codes listed for your component — you still

cannot get the Commander to work properly, try the search

method described under “Setting by Searching for the Correct

Code”.

Notes

• Be sure to proceed to each next step in the above procedure within 10

seconds; otherwise, the setting mode will be canceled.

• You cannot set up more than one component at a time on each position of the

slide switch. If you want to set up two or more same components of different

brands, see “Setting Another TV, VCR, or Satellite Tuner”.

Tip

You can write down the code number on the label inside the battery

compartment lid.

Setting by Searching for the Correct Code

If you’ve tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component

was not listed), try the following.

1 Turn on the component you wish to set up using its power

switch.

2 Set the slide switch on the Remote Commander to the desired

position.

3 Press the S (Set) button.

4 Aim the Commander to your component, and press and release

the PROGR+ button. Then press and release the u button.

5 Repeat step 4 until the correct code number is found.

Each time you press the PROGR+ button and then the u button, a

new code number will be transmitted.

Keep trying until your component operates as follows:

•TV, VCR or satellite tuner : the power turns off.

•TV without a power switch: the Channel + function works.

Be patient as you do this; it may take up to about 100 tries for a

TV, and 70 to 80 tries for other components until the correct code

number is located.

6 When the correct code is found, press the … button.

7 Turn on the component again, and check that the Commander

can control the other functions of your component such as

channel and volume control.

If the component does not operate properly, repeat steps 3 to 6 and

search for another code.

If you still cannot get the Commander to work properly, see

“Troubleshooting”.

Note

Be sure to proceed to each next step in the above procedure within 10 seconds;

otherwise setting mode will be canceled.

Setting Another TV, VCR, or Satellite Tuner

When you have two or more components of the same type (for

example, three VCRs), you can set the code number of the

component’s type on any empty position of the slide switch of the

Remote Commander (AUX or SAT position only).

1 Set the slide switch on the Remote Commander to AUX or SAT.

2 Press the S (Set) button.

3 Press the p button.

4 Press one of the following buttons;

1 to set up a VCR

8 to set up a TV

9 to set up a satellite tuner

5 Press the … button.

6 Enter the component’s code number by following steps 2 to 5 of

“Setting by Entering the Code Number”, or steps 3 to 7 of

“Setting by Searching for the Correct Code”.

3-866-334-11(1)

RM-V201T

Setting the Component Codes Operating a Component

1 Set the slide switch to the position of your component.

2 Point the Commander directly to your component and press

the button for the desired function.

See “Remote Button Descriptions” for details.

Notes on using the Commander

• Using this Commander will not add new functions to your components. The

functions of the Commander are limited to the functions of the component

itself. For example, if your TV does not have a mute function, the ¤ button

on this Commander will not function with your TV.

• Do not forcibly remove or tear off the corner protector.

Troubleshooting

If you’re having problems setting up or using the Remote

Commander:

•When setting up the Commander, carefully go through the

procedures described under “Setting the Component Codes”. If the

code that’s listed first for your component doesn’t work, try all the

codes for your component — in the order in which they’re listed. If

all the codes fail to work (or if your component is not listed), try

using the procedures under “Setting by Searching for the Correct

Code”.

•Check that you’re aiming the Commander directly at the

component, and that there are no obstructions between the

Commander and the component.

•Make sure the batteries you’re using are not worn out, and that

they’re inserted correctly.

•Check that the slide switch of the Remote Commander is set to the

position (TV, VCR, SAT or AUX) for your desired component.

•If you cannot preset a component to the AUX or SAT position of

the slide switch, a component type different from that of the

component you intend to preset may be assigned to that position.

In such a case, follow the procedure in “Setting Another TV, VCR,

or Satellite Tuner” first.

•Check that the component has infrared remote capability. For

example, if your component didn’t come with a remote control, it

probably isn’t capable of being controlled by the Remote

Commander.

•Should any problem persist, reset the Commander to the factory

setting by pressing the u, … and Á– buttons simultaneously.

If you have any questions or problems concerning the Remote

Commander that are not covered in this manual, please call the

telephone number in the warranty.

Operating a TV/Satellite Tuner

Remote Button Descriptions

Operating a VCR

!™ To select a number between 20

and 29.

!£ To enter the selection.

!¢ Programme up: +

Programme down: –

!∞ To operate JUMP,

FLASHBACK or CHANNEL

RETURN function on the

satellite tuner, depending on

the manufacturer’s setting.

Satellite Tuner

1 To switch to Teletext.

2 To change the input mode.

3 Fastext buttons.

4 To change the programme.

Also to turn on the power.

5 To select double-digit numbers.

Works in the same way as your

TV’s commander.

6 To move the cursor upward,

downward, to the right or left.

7 To call up the MENU display.

8 Volume up: +

Volume down: –

9 To mute volume on TV.

0 To turn off the power.

!¡ To turn on.

To return from Teletext to TV.

!™ To select a number between 20

and 29.

!£ To enter the selection.

!¢ Programme up: +

Programme down: –

!∞ To operate JUMP,

FLASHBACK, or CHANNEL

on the TV, depending on the

manufacturer’s setting.

1 To switch the signals supplied to

the TV.

2 To change the programme.

3 To select double-digit numbers.

Works in the same way as your

VCR’s commander.

4 To play

5 To rewind

6 To record, press ( while

pressing r.

7 To control the volume on TV.

8 To mute the volume on TV.

9 To turn on and off the power.

0 To select a number between 20

and 29.

!¡ To fast-forward

!™ To stop

!£ To pause

!¢ Programme up: +

Programme down: –

2 To change the input mode

(H/V).

4 To change the programme.

5 To select double-digit numbers.

Work in the same way as your

satellite tuner’s commander.

6 To move the cursor upward,

downward, to the right or left.

7 To call up the MENU display.

8 To control the volume on TV.

9 To mute the volume on TV.

0 To turn on and off the power.

Installing the Batteries

Open the battery compartment and insert two R6 (size AA) batteries

(not supplied).

Be sure to line up the + and – on the batteries with the + and – on the

battery compartment.

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the

Remote Commander does not operate properly, the batteries might

be worn out. Replace the batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than 20 minutes to replace the batteries; otherwise, your

setting of the code numbers will be erased.

Notes on Batteries

•Do not mix old batteries with new ones or mix different types of

batteries together.

•If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

!¡

!™

!£

!¢

!∞

!¡

!™

!¢

!£

About this Remote Commander

You can set up this Remote Commander to operate the following

components of almost all major brands including Sony.

Specifications

Operable distance

Approx. 10 m (33 ft) (varies depending on the component of

each manufacturer)

Power requirements

Two R6 (size AA) batteries (not supplied)

Battery life

Approx. six months (varies depending on frequency of use)

Dimensions

Approx. 63 × 200 × 38 mm (w/h/d) (2

/2 × 7

/8 × 1

/2 in.)

Mass

Approx. 120 g (4.2 oz.) (not including batteries)

Design and specifications are subject to change without notice.

Remote Commander

Operating Instructions

Mode d’emploi (au verso)

English

Position

VCR

AUX

SAT

Component that can be preset

VCR

Factory setting

Sony TV

Sony VHS VCR (VTR3)

Sony DV (VTR4)

Sony satellite tuner

TV, VCR, or satellite tuner

Sony rm v 201 t Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info