51498
15
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
3-864-335-12(1)
1998 by Sony Corporation
GB
F
ES
TA-FB920R
TA-FB820R
TA-FB720R
Operating Instructions
Mode d’emploi
Manual de instrucciones
Manual de instruções
Integrated
Stereo Amplifier
P
2
GB
WARNING
To prevent fire or shock
hazard, do not expose the unit
to rain or moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
Do not install the appliance in
a confined space, such as a
bookcase or built-in cabinet.
Precautions
On safety
Do not disassemble the cabinet as this
may result in an electrical shock.
Refer servicing to qualified personnel
only.
Should any solid object or liquid fall
into the cabinet, unplug the amplifier
and have it checked by qualified
personnel before operating it any
further.
On power sources
Before operating the amplifier, check
that the operating voltage of the
amplifier is identical with your local
power supply. The operating voltage
is indicated on the nameplate at the
rear of the amplifier.
If you are not going to use the
amplifier for a long time, be sure to
disconnect the amplifier from the wall
outlet. To disconnect the AC power
cord (mains lead), grasp the plug
itself; never pull the cord.
AC power cord must be changed only
at the qualified service shop.
On placement
Place the amplifier in a location with
adequate ventilation to prevent heat
built-up and prolong the life of the
amplifier.
Do not place the amplifier near heat
sources, or in a place subject to direct
sunlight, excessive dust or mechanical
shock.
Do not place anything on top of the
cabinet that might block the
ventilation holes and cause
malfunctions.
On operation
Before connecting other components, be
sure to turn off and unplug the
amplifier.
On cleaning the amplifier
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine.
On the prevention of howling
Do the following:
lower the volume.
keep the turntable as far from the
speakers as possible.
use commercially available audio
insulators on the bottom of the
turntable.
keep the microphone away from the
speakers during use.
For further protection against howling,
set the speakers or turntable on top of a
heavy wooden board or concrete slab.
If you have any questions or problems
concerning your amplifier, please
consult your nearest Sony dealer.
GB
3
GB
z When to replace batteries
With normal use, the batteries should last for about 6 months. When the remote
no longer operates the amplifier, replace all the batteries.
Notes
Do not leave the remote near an extremely hot or humid place.
Do not drop any foreign object into the remote casing, particularly when replacing
the batteries.
Do not expose the remote sensor to direct sunlight or lighting equipment. Doing
so may cause a malfunction.
If you don’t use the remote for an extended period of time, remove the batteries to
avoid possible damage from battery leakage and corrosion.
Unpacking
Check that you have received the following supplied items:
Remote commander (remote) (1) RM-S316
Sony batteries R6 (size-AA) (2)
Inserting batteries into the remote
Insert two R6 (size-AA) batteries, matching the + and – on the batteries with
the markings inside the battery compartment. When using the remote, point
it at the remote control sensor g on the amplifier.
TABLE OF CONTENTS
Getting Started
Hookup Overview 4
Audio Component Hookups 4
Speaker System Hookups 5
Mains Lead Hookups 6
Listening to the Music 7
Recording 9
Additional Information
Troubleshooting 10
Specifications 10
Rear Panel Descriptions 12
Remote Button Descriptions 12
Welcome!
Thank you for purchasing the Sony
Integrated Stereo Amplifier. Before
operating the amplifier, please read this
manual thoroughly and retain it for
future reference.
About This Manual
The instructions in this manual are for
models TA-FB920R, FB820R, and
FB720R. Check your model number by
looking at the rear panel of your
amplifier. The TA-FB920R is the model
used for illustration purposes unless
stated otherwise.
Any difference in operation is clearly
indicated in the text, for example,
“TA-FB920R only.”
Conventions
Instructions in this manual describe
the controls on the amplifier.
For details on the remote buttons
control, see ”Remote Button
Descriptions” on page 12.
The following icon is used in this
manual:
z Indicates hints and tips for making
the task easier.
Getting Started
4
GB
Ç
L
R
L
R
OUTPUT
LINE
CD
IN
Speaker (L)
Speaker (R)
TV or video
deck
Hookup Overview
The amplifier allows you to connect and control the
following audio components. Follow the hookup
procedure indicated for each component that you want
to connect.
To learn the location and name of each jack, see ”Rear
Panel Descriptions” on page 12.
Tape deck
DAT deck
Tuner
CD player
Before you get started
Turn off the power to all components before making
any connections.
Do not connect the mains leads of the various
components until all connections are completed.
Use the audio connecting cords supplied with each
component for hooking up with the amplifier.
Purchase and use optionally available cords as
required.
Be sure to make connections firmly to prevent hum
and noise.
When connecting an audio connecting cord, be sure
to match the R (right) and L (left) jacks of the
amplifier to the R and L jacks on the other
components.
Audio Component Hookups
Overview
Here you learn how to connect your audio components
to the amplifier.
Turntable
Getting Started
MD deck
What cords will I need?
Audio connecting cord (not supplied) (2 for each tape deck,
DAT deck, or MD deck; 1 for other components)
Hookups
The arrow ç indicates signal flow.
CD player
Amplifier
Amplifier
Tuner
Tuner
CD player
White (L)
Red (R) Red (R)
White (L)
Ç
L
R
L
R
OUTPUT
LINE
TUNER
IN
PROTECTION
U
PHONES
SPEAKERS
A
OFF
A
+
B
10
+
10
TONE
SUBSONIC
EON LINK
INPUT SELECTOR
VOLUME
SOURCE DIRECT
010
B
g
SOURCE
TAPE1 TAPE2
BASS
0
10
+
10
TREBLE
0
LEFT RIGHT
BALANCE
TAPE MONITOR
TAPE1/DATEON LINK CD TUNER PHONOAUXTAPE2/MD
LOUDNESS
Ø ON ø OFF Ø ON ø OFF
PHONO TAPE1/DAT
EON CONTROL INTUNER TAPE2/MDCD
y
AUX
SPEAKERS
EON CONTROL
R
B
A
L
++––
RL
++––
TAPE1/DAT
L
REC OUT IN
IMPEDANCE USE 4–16
A+B USE 8–16
BI WIRE USE 4–16
IN
R
L
R
TAPE2/MD
REC OUT IN
AUX
IN
CD
IN
TUNER
IN
L
R
PHONO
IN
SIGNAL
GND
y
Getting Started
5
GB
Ç
L
R
PHONO
IN
Ç
ç
OUTPUT
LINE
L
R
INPUT
LINE
TAPE1/DAT
L
R
REC OUT IN
Tape deck, DAT deck, or MD deck
Use the configuration above to connect the OUTPUT and
INPUT jacks of:
a tape deck or DAT deck to the TAPE1/DAT jacks.
a tape deck or MD deck to the TAPE2/MD jacks.
Turntable
Tape deck
Amplifier
Amplifier
Turntable
Note
To prevent hum, connect the earth lead to SIGNAL GND (y)
on the amplifier.
TV or video deck
Ç
L
R
L
R
OUTPUT
LINE
AUX
IN
Amplifier TV or video deck
EON CONTROL
Amplifier
Tuner
Ç
EON CONTROL
IN
EON CONTROL
OUT
If your tuner is equipped with an EON CONTROL OUT
terminal, connect it to the EON CONTROL IN terminal on
the amplifier to allow use of the EON (Enhanced Other
Networks) function of the RDS (Radio Data System) (see
page 8).
(+)
(–)
(+)
(–)
Speaker System Hookups
Overview
Here you learn how to connect speakers to the
amplifier. You can connect two pairs of speakers,
SPEAKERS A and B.
What cords will I need?
Speaker cord (not supplied) (1 for each speaker)
Twist the stripped ends of the cord about 15mm. Be sure to
match the speaker cord to the appropriate terminal on the
components: + to + and – to –. If the cords are reversed, the
sound will be distorted and will lack bass.
Hookups
SPEAKERS A SPEAKERS B
SPEAKERS
EON CONTROL
R
B
A
L
++––
RL
++––
TAPE1/DAT
L
REC OUT IN
IMPEDANCE USE 4–16
A+B USE 8–16
BI WIRE USE 4–16
IN
R
L
R
TAPE2/MD
REC OUT IN
AUX
IN
CD
IN
TUNER
IN
L
R
PHONO
IN
SIGNAL
GND
y
]
}
]
}
Getting Started
6
GB
Connecting to bi-wire system speakers
Since the two pairs of speaker terminals on your
amplifier, SPEAKERS A and B, can provide
simultaneous speaker output, you can use them to
connect a bi-wire speaker system. To drive both
speaker systems simultaneously, set SPEAKERS to
A+B.
To select the speaker system A or B
Set SPEAKERS to A or B. To drive both speaker systems
simultaneously, set SPEAKERS to A+B.
Note
Use speakers with a nominal impedance of 4 to 16 ohms.
When outputting at the same time to two speaker systems,
use speakers with a nominal impedance of 8 to 16 ohms.
Mains Lead Hookups
Connecting the mains lead
Connect the mains lead from this amplifier and from
your audio/video components to wall outlets.
z You can power other components through AC
OUTLET on the amplifier (unavailable on the U.K.
model)
By connecting other audio components to AC OUTLET
on the amplifier, you can supply power to the
connected components through the amplifier and turn
them all on or off when you turn the amplifier on or off.
Caution
Make sure that the total power consumption of all
components connected to the outlets on the amplifier does
not exceed 100 watts. Do not connect electrical home
appliances such as an electric iron, fan, TV, or other high-
wattage appliances to these outlets.
Note
Separate the mains lead, audio connecting cords and speaker
cords. Noise or sound deterioration may occur when audio
connecting cords are in contact with the mains lead, or when
the mains lead or speaker cords are placed near the tuner’s
loop aerial or aerial wire.
Basic Operations
7
GB
Basic Operations
Basic Operations
Listening to the Music
z To listen through the
headphones
Connect the headphones to
PHONES and set
SPEAKERS to OFF.
z To listen directly to the
input signal
Press SOURCE DIRECT so
that the indicator lights up.
Since the circuits of TONE
controls, BALANCE control,
LOUDNESS button, and
SUBSONIC button are
bypassed, you cannot adjust
bass, treble, the balance,
reinforce the bass and treble,
or reduce subsonic noise
components while listening
to a source directly.
Note
Avoid high speaker output at
which the sound is distorted.
High-frequency distortion may
damage the tweeters.
1
Press U to turn on the amplifier and turn VOLUME fully
counterclockwise to prevent damaging the speakers with
excessive output.
The PROTECTION indicator lights up, then goes off.
2
Turn on the programme source you want to listen to.
3
Set INPUT SELECTOR to the respective programme source.
The indicator for the programme source lights up.
4
Start the programme source.
5
Adjust the volume by turning VOLUME.
To
Press or turn
BASS
TREBLE
BALANCE
LOUDNESS
SUBSONIC
Adjust the bass
Adjust the treble
Adjust the balance
Reinforce the bass and treble at low
listening level
Reduce subsonic noise components
created by warped records, etc.
AUX
TAPE1/DAT
TAPE2/MD
Source connected to AUX
Record
Radio broadcast
Compact disc
To listen to a
Turn INPUT SELECTOR for
PHONO
TUNER
CD
Source connected to:
—TAPE1/DAT
—TAPE2/MD
5
1
3
PROTECTION
U
PHONES
SPEAKERS
A
OFF
A
+
B
10
+
10
TONE
SUBSONIC
EON LINK
INPUT SELECTOR
VOLUME
SOURCE DIRECT
010
B
g
SOURCE
TAPE1 TAPE2
BASS
0
10
+
10
TREBLE
0
LEFT RIGHT
BALANCE
TAPE MONITOR
TAPE1/DATEON LINK CD TUNER PHONOAUXTAPE2/MD
LOUDNESS
Ø ON ø OFF Ø ON ø OFF
5
1
3
PROTECTION
U
PHONES
SPEAKERS
A0
BASS
OFF
A
+
B
10
+
10
TONE
SUBSONIC
INPUT SELECTOR VOLUME
SOURCE DIRECT
EON LINK
010
Ø ON ø OFF
LOUDNESS
Ø ON ø OFF
B
g
SOURCE
TAPE1
0
TREBLE
10
+
10
BALANCE
TAPE MONITOR
CD
TUNERAUX
TAPE2/MD
TAPE1/DAT
PHONO
LEFT RIGHT
TA-FB920R TA-FB820R/FB720R
Basic Operations
8
GB
To receive the Enhanced Other Networks (EON) programmes
When your ampifier is connected to a Sony tuner with the EON CONTROL
system, the amplifier switches to any EON programme that is broadcast in
your EON area, and switches back to the last selected programme source
when the programme ends.
z What is the Enhanced
Other Networks (EON)?
One convenient RDS service
is ”Enhanced Other
Networks” (or ”EON”).
This allows the unit to
automatically switch to a
programme type of your
choice when one starts in
your broadcast area.
1 Make sure that the amplifier and the tuner are connected through the
EON CONTROL terminals (see page 5).
2 Press EON LINK so that the indicator lights up.
Whenever an EON programme starts on the radio frequency that your
tuner is set to, you will receive it.
To cancel EON reception
Press EON LINK again so that the indicator goes off.
Notes
If you select another programme source while receiving an EON programme, EON
reception ends. However, as long as the EON LINK indicator lights up, you can
receive EON programmes automatically.
Make sure to cancel EON reception before starting to record since an EON
programme may interfere with your recording.
If you activate the Tape Monitor function (see page 9) while the EON LINK indicator
is lit, the indicator goes off and you cannot receive EON programmes. If this
happens, deactivate the Tape Monitor function so that the indicator lights up again.
PROTECTION
U
PHONES
SPEAKERS
A
OFF
A
+
B
10
+
10
TONE
SUBSONIC
EON LINK
INPUT SELECTOR
B
g
SOURCE
TAPE1 TAPE2
BASS
0
10
+
10
TREBLE
0
LEFT RIGHT
BALANCE
TAPE MONITOR
TAPE1/DATEON LINK CD TUNER PHONOAUXTAPE2/MD
LOUDNESS
Ø ON ø OFF Ø ON ø OFF
EON LINK
PROTECTION
U
PHONES
SPEAKERS
A0
BASS
OFF
A
+B
10 +10
TONE
INPUT SELECTOR
LOUDNESS
Ø ON ø OFF
B
g
SOURCE
TAPE1
0
TREBLE
10 +10
BALANCE
TAPE MONITOR
CD
TUNERAUX
TAPE2/MD
TAPE1/DAT
PHONO
LEFT RIGHT
EON LINK
EON LINK
TA-FB920R TA-FB820R/FB720R
Basic Operations
9
GB
Basic Operations
Recording
4
Prepare the recording component for recording, then start
recording.
5
Start playing the programme source.
Set INPUT SELECTOR to
Source connected to:
—TAPE1/DAT
—TAPE2/MD
z You can record the same
source on two recording
components at the same
time
z You can monitor the
recorded sound (Tape
Monitor function)
You can monitor the
recorded sound if the tape
deck you are recording on
has separate playback and
recording heads.
To monitor the sound, set
TAPE MONITOR to TAPE1
or TAPE2.
Note that on the
TA-FB820R/FB720R, you
can monitor the only sound
being recorded from the
TAPE1/DAT jacks.
1
Press U to turn on the amplifier.
2
Turn on the programme source you want to record.
3
Select the programme source that you want to record by
turning INPUT SELECTOR.
The indicator for the programme source lights up.
TAPE1/DAT
TAPE2/MD
To record a
PHONO
TUNER
CD
Radio broadcast
Compact disc
Record
AUX
Source connected to AUX
TA-FB920R TA-FB820R/FB720R
13
PROTECTION
U
PHONES
SPEAKERS
A
OFF
A+B
10 +10
TONE
SUBSONIC
EON LINK
INPUT SELECTOR
VOLUME
SOURCE DIRECT
010
B
g
SOURCE
TAPE1 TAPE2
BASS
0
10 +10
TREBLE
0
LEFT RIGHT
BALANCE
TAPE MONITOR
TAPE1/DATEON LINK CD TUNER PHONOAUXTAPE2/MD
LOUDNESS
Ø ON ø OFF Ø ON ø OFF
1 3
PROTECTION
U
PHONES
SPEAKERS
A0
BASS
OFF
A
+
B
10
+
10
TONE
SUBSONIC
INPUT SELECTOR VOLUME
SOURCE DIRECT
EON LINK
010
Ø
ON
ø
OFF
LOUDNESS
Ø
ON
ø
OFF
B
g
SOURCE
TAPE1
0
TREBLE
10
+
10
BALANCE
TAPE MONITOR
CD
TUNERAUX
TAPE2/MD
TAPE1/DAT
PHONO
LEFT RIGHT
11
GB
Additional Information
General
System
Power amplifier: Pure-complementary SEPP OCL
power amplifier with all stages directly coupled
Preamplifier: Low-noise, equalizer amplifier
Power requirements
230 V AC, 50/60 Hz
Power consumption
TA-FB920R: 210 W
TA-FB820R: 180 W
TA-FB720R: 170 W
Dimensions (approx.) (w/h/d)
TA-FB920R: 430 × 150 × 410 mm
TA-FB820R/FB720R: 430 × 150 × 405 mm
incl. projecting parts and controls
Mass (approx.)
TA-FB920R: 10.3 kg
TA-FB820R: 9.3 kg
TA-FB720R: 8.6 kg
Supplied accessories
See page 3.
Design and specifications are subject to change without
notice.
3
F
F
Déballage
Vérifiez que les articles suivants se trouvent bien dans l’emballage:
Télécommande (1) RM-S316
Piles Sony R6 (format AA) (2)
Mise en place des piles dans la télécommande
Insérez deux piles R6 (format AA) en faisant correspondre les pôles + et –
des piles avec les indications dans le logement des piles. Quand vous utilisez
la télécommande, dirigez-la vers le capteur de télécommande g de
l’amplificateur.
TABLE DES MATIÈRES
Préparatifs
Raccordements 4
Raccordement d’appareils audio 4
Raccordement des enceintes 5
Raccordement du cordon d’alimentation secteur 6
Ecoute d’une source musicale 7
Enregistrement 9
Informations additionnelles
Guide de dépannage 10
Spécifications 10
Description du panneau arrière 12
Description des touches de la télécommande 12
Bienvenue!
Nous vous remercions pour l’achat de
cet amplificateur stéréo intégré. Avant
de l’utiliser, veuillez lire attentivement
ce mode d’emploi et le conserver pour
toute référence ultérieure.
A propos de ce
mode d’emploi
Les instructions de ce mode d’emploi
concernent les modèles TA-FB920R,
FB820R, et FB720R. Vérifiez le numéro
de votre modèle sur le panneau arrière
de l’amplificateur.
Le TA-FB920R est le modèle utilisé dans
les illustrations, sauf spécification
contraire. Toute différence de
fonctionnement est clairement indiquée
dans le texte, par exemple “TA-FB920R
seulement”.
Conventions
Les instructions dans ce mode
d’emploi décrivent les commandes de
l’amplificateur.
Pour les touches de la télécommande,
voir “Description des touches de la
télécommande”, page 12.
L’icône suivante est utilisée dans ce
mode d’emploi:
z Indique des conseils et méthodes
qui facilitent une manipulation.
z Quand faut-il remplacer les piles?
En fonctionnement normal, les piles devraient durer environ 6 mois. Remplacez
toutes les piles quand la télécommande ne peut plus piloter l’amplificateur.
Remarques
Ne laissez pas la télécommande à un endroit extrêmement chaud ou humide.
Ne laissez rien tomber dans son boîtier, en particulier au remplacement des piles.
N’exposez pas la télécommande en plein soleil ou sous un dispositif d’éclairage.
Cela pourrait provoquer un mauvais fonctionnement.
Si la télécommande doit rester inutilisée pendant une période prolongée, retirez
les piles pour éviter tout dommage dû à une fuite des piles ou à la corrosion.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sony TA-FB820 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sony TA-FB820 in de taal/talen: Engels, Frans, Spaans, Pools als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Sony TA-FB820

Sony TA-FB820 Gebruiksaanwijzing - Nederlands, Deutsch, Italiano, Svenska - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info