67640
19
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
19
GB
Continued
5 Press the DVD button, the
press the 1 (power) button.
6 Press the OTHER button
repeatedly, press the Label
select button corresponding to
the amplifier, then press the 1
(power) button.
7 Press the t (input select)
button repeatedly to select the
appropriate video input on the
TV to watch the DVD.
8 Press the input select button
on the amplifier to select the
appropriate audio input to
watch the DVD.
9 Press the DVD button, then
press N.
10
Press the (light) button.
A beep sounds and programming is
complete.
11
Press the (light) button or
the RETURN button twice.
The set mode closes, and the Remote
Commander returns to standby for
operating the A/V components.
Notes
If the procedure is interrupted at any point for
over 60 seconds, programming is cancelled.
You cannot continue from where you left off.
If you try to programme actions on a button
that already has a programmed Component
Macro, a beep sounds twice to alert you that
you cannot programme a Component Macro
on the button. In such a case, clear the
programmed Component Macro (page 20),
then start programming again from step 1.
•You cannot clear steps during the
programming procedure. If you make a
mistake in programming actions, finish
programming once and clear the Component
Macro (page 20), then start again from step 1.
•You can programme up to 32 consecutive
operation actions. When up to 32 steps are
programmed, programming of the Component
Macro is full. To change the programmed
steps, clear the Component Macro (page 20),
then start over from step 1.
Checking if a Component
Macro is executed properly
Follow the procedure below to check if
the programmed Component Macro
works as intended.
To execute a Component
Macro
1 Press and hold the
COMPONENT select button
on which the desired
Component Macro has been
programmed for over 2
seconds.
The signal transmission icon appears
on the screen, and the programmed
Component Macro is executed.
Tip
While the signal transmission icon ( )
appears and the Component Macro is executed,
“CANCEL” appears in the third line of the
screen. You can cancel executing the
Component Macro by pressing the right Label
select button.
To check the programmed
steps of a Component Macro
and add a delay action
Delay action allows you to set an interval
between steps. Delay time is set to 250
ms. (1/4 second) on the Remote
Commander.
If a Component Macro is not executed as
intended, check the programmed steps
and try adding a delay to execute the
programme properly.
1 While pressing the (light)
button, press the OTHER
button.
“SET MODE” appears as the screen
title.
2 Press the V/v buttons to
select “4 MACRO”, then press
the OK button or the centre
Label select button.
“MACRO” appears as the screen title.
Tip
If a number is displayed before the menu,
you can select the menu by pressing the
number button.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sony RMVL1400T.CE7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sony RMVL1400T.CE7 in de taal/talen: Engels als bijlage per email.

De handleiding is 2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sony RMVL1400T.CE7

Sony RMVL1400T.CE7 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano - 180 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info