61565
3
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
© 2008 Sony Corporation 3-878-284-14(1)
KDL-32L40xx
KDL-26L40xx
KDL-19L40xx
Operating Instructions
LCD Digital Colour TV
2
GB
NOTICE FOR
CUSTOMERS IN THE
UNITED KINGDOM
A moulded plug complying with BS1363 is fitted to this
equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced
with the same rating of fuse approved by ASTA or BSI to
BS 1362 (i.e., marked with or ) must be used.
When an alternative type of plug is used it should be fitted
with the same rating of fuse, otherwise the circuit should be
protected by a 10 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable
fuse cover, be sure to attach the fuse cover after you change
the fuse. Never use the plug without the fuse cover. If you
should lose the fuse cover, please contact your nearest
Sony service station.
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and
replace the fuse.
Please refer to the illustration that actually equipped with
the product.
Thank you for choosing this Sony product.
Before operating the TV, please read this manual
thoroughly and retain it for future reference.
Any functions related to Digital TV ( ) will only
work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm
with your local dealer if you can receive a DVB-T signal
where you live.
Although this TV set follows DVB-T specifications,
compatibility with future DVB-T digital terrestrial
broadcasts cannot be guaranteed.
Some Digital TV functions may not be available in some
countries.
is a registered trademark of the DVB Project
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
The “xx” that appears on the model name, corresponds to
two numeric digits related to design or colour variation.
Introduction
Notice for Digital TV function
FUSE
FUSE
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-
0075 Japan. The Authorized Representative for EMC
and product safety is Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to
the addresses given in separate service or guarantee
documents.
Trademark information
About the model name in this manual
3
GB
Safety information.............................................................................................................8
Precautions......................................................................................................................10
Overview of the remote ..................................................................................................11
Overview of the TV buttons and indicators ..................................................................12
Watching TV ....................................................................................................................13
Checking the Digital Electronic Programme Guide (EPG) .................................16
Using the Digital Favourite list .............................................................................17
Connecting optional equipment ....................................................................................18
Viewing pictures from connected equipment ..............................................................19
Using control for HDMI ...................................................................................................20
Navigating through menus.............................................................................................21
Picture Adjustment menu...............................................................................................22
Sound Adjustment menu................................................................................................24
Features menu.................................................................................................................25
Set-up menu ....................................................................................................................27
Digital Set-up menu ........................................................................................................30
Installing the Accessories (Wall-Mount Bracket).........................................................32
Specifications..................................................................................................................35
Troubleshooting..............................................................................................................37
Start-up Guide 4
Watching TV
Using Optional Equipment
Using MENU Functions
Additional Information
Table of Contents
: for digital channels only
4
GB
Start-up Guide
1: Checking the
accessories
Remote RM-ED014 (1)
Size AA batteries (R6 type) (2)
Stand (1)
Screws for stand (3)
Cable band (1)
To insert batteries into the remote
~
Observe the correct polarity when inserting batteries.
Do not use different types of batteries together or mix
old and new batteries.
Dispose of batteries in an environmentally friendly way.
Certain regions may regulate disposal of batteries.
Please consult your local authority.
Handle the remote with care. Do not drop or step on it,
or spill liquid of any kind onto it.
Do not place the remote in a location near a heat source,
a place subject to direct sunlight, or a damp room.
2: Attaching the stand
Follow the assembling steps required to place on a
TV stand.
1 Take out the Table-Top Stand and screws
from the carton. The screws are found in
the accessory bag.
KDL-32L40xx/KDL-26L40xx
KDL-19L40xx
2 Gently slide the TV unit onto the neck of
the Table-Top Stand and align the screws
holes.
~
When you carry the TV, place your hand as illustrated
and hold it securely, see page 8. Do not put stress on the
LCD panel and the frame around the screen.
Be careful not to pinch your hands or the mains lead
when you install the TV to the Table-Top Stand.
3 Use the supplied screws to attach the TV
unit to the Table-Top Stand.
~
If an electric screw driver is used, set the torque to
tighten at approximately 1.5 N·m {15 kgf·cm}.
Unless otherwise stated, illustrations here are for KDL-
32L40xx.
Push and slide to open.
Accessory bag Screws
TV unit
Table-Top
Stand
Accessory bag Screws
TV unit
Table-Top
Stand
Rear of TV
Screws
5
GB
Start-up Guide
3: Connecting an
aerial/VCR/ DVD
recorder
~
AV1 outputs available only for analogue TV.
AV2 outputs to the current screen (except PC,
HDMI1,2, Component 1080i).
This product has been tested and found to compliant with the limits set out in the EMC Directive for using
connection cables not longer than 3 meters (9.8 feet).
Coaxial cable
Connecting an aerial only
AV1 AV2
Connecting an aerial/ VCR/ DVD recorder with SCART
Scart lead
VCR/ DVD recorder
Coaxial cable
Coaxial cable
1 2
Connecting an aerial/ VCR/ DVD recorder with HDMI
HDMI cable
Coaxial cable
Coaxial cable
VCR/ DVD recorder
Continued
6
GB
4: Preventing the TV
from toppling over
KDL-32L40xx, KDL-26L40xx only
1 Install a wood screw (4 mm in diameter,
not supplied) in the TV stand.
2 Install a machine screw (M6 × 12-14 mm,
not supplied) into the screw hole of the TV.
3 Tie the wood screw and the machine
screw with a strong cord.
5: Bundling the cables
You can bundle the connecting cables as illustrated
below.
~
Do not bundle the mains lead with other connecting cables.
6:
Selecting the
language, country/region
and location
1 Connect the TV to your mains socket
(220-240V AC, 50Hz).
2 Press 1 on the top edge of the TV.
When you turn on the TV for the first time, the
Language menu appears on the screen.
~
When you turn on the TV, the power indicator flashes
in green.
3 Press F/f to select the language
displayed on the menu screens, then
press .
2
1
3
3,4,5
RETURN TOOLS
AUDIO
ANALOGDIGITAL
GUIDE
MENU
Select: Confirm:
Language
Country
Location
English
Nederlands
Italiano
Deutsch
Auto Start-up
7
GB
Start-up Guide
4 Press F/f to select the country/region in
which you will operate the TV, then press
.
If the country/region which you want to use on
the TV does not appear in the list, select “-”
instead of a country/region.
5 Press F/f to select the location type in
which you will operate the TV, then
press .
This option selects the initial picture mode
appropriate for the typical lighting condition in
these environments.
7: Auto-tuning the TV
1 Before you start auto-tuning the TV, insert
a pre-recorded tape into the VCR
connected to the TV (page 5) and start
play back.
The video channel will be located and stored on
the TV during auto-tuning.
If no VCR is connected to the TV, skip this step.
2 Press .
The TV starts searching for all available digital
channels, followed by all available analogue
channels. This may take some time, so do not
press any buttons on the TV or remote while
proceeding.
If a message appears for you to confirm the
aerial connection
No digital or analogue channels were found.
Check all the aerial connections and press to
start auto-tuning again.
3 When the Programme Sorting menu
appears on the screen, follow the steps of
“Programme Sorting” (page 27).
If you do not change the order in which the
analogue channels are stored on the TV, go to
next step.
4 Press MENU to exit.
The TV has now tuned in all the available
channels.
Detaching the Table-
Top Stand from the TV
~
Do not remove the Table-Top Stand for any reason other
than to wall-mount the TV.
Select:Back: Confirm:
Language
Country
Location
-
United Kingdom
Ireland
Nederland
Luxembourg
France
Italia
Auto Start-up
Language
Country
Location
Home
Shop
Select:Back: Confirm:
Auto Start-up
Back: Start:
Do you want to start Auto Tuning?
Auto Tuning
Table-Top
Stand
8
GB
Safety information
Installation/Set-up
Install and use the TV set in accordance with the
instructions below in order to avoid any risk of fire,
electrical shock or damage and/or injuries.
Installation
The TV set should be installed near an easily accessible
mains socket.
Place the TV set on a stable, level surface.
Only qualified service personnel should carry out wall
installations.
For safety reasons, it is strongly recommended that you
use Sony accessories, including:
KDL-32L40xx:
Wall-mount bracket SU-WL500
KDL-26L40xx/KDL-19L40xx:
Wall-mount bracket SU-WL100
Be sure to use the screws supplied with the Wall-mount
bracket when attaching the mounting hooks to the TV
set.
The supplied screws are designed so that they are 8 mm
to 12 mm in length when measured from the attaching
surface of the mounting hook.
The diameter and length of the screws differ depending
on the Wall-mount bracket model. Use of screws other
than those supplied may result in internal damage to the
TV set or cause it to fall, etc.
Transporting
Before transporting the TV set, disconnect all cables.
Two or more people are needed to transport a large TV
set.
When transporting the TV set by hand, hold it as shown
below. Do not put stress on the LCD panel and the frame
around the screen.
When lifting or moving the TV set, hold it firmly from
the bottom.
When transporting the TV set, do not subject it to jolts
or excessive vibration.
When transporting the TV set for repairs or when
moving, pack it using the original carton and packing
material.
Ventilation
Never cover the ventilation holes or insert anything in
the cabinet.
Leave space around the TV set as shown below.
It is strongly recommended that you use a Sony wall-
mount bracket in order to provide adequate air-
circulation.
Installed on the wall
Installed with stand
Screw (supplied with the
Wall-mount bracket)
Mounting Hook
Hook attachment on rear of TV set
8-12 mm
30 cm
10 cm
10 cm
10 cm
Leave at least this space around the set.
30 cm
10 cm10 cm
6 cm
Leave at least this space around the set.
9
GB
To ensure proper ventilation and prevent the collection
of dirt or dust:
Do not lay the TV set flat, install upside down,
backwards, or sideways.
Do not place the TV set on a shelf, rug, bed or in a
closet.
Do not cover the TV set with a cloth, such as curtains,
or items such as newspapers, etc.
Do not install the TV set as shown below.
Mains lead
Handle the mains lead and socket as follows in order
to avoid any risk of fire, electrical shock or damage
and/or injuries:
Use only mains leads supplied by Sony, not other
suppliers.
Insert the plug fully into the mains socket.
Operate the TV set on a 220-240 V AC supply only.
When wiring cables, be sure to unplug the mains lead
for your safety and take care not to catch your feet on
the cables.
Disconnect the mains lead from the mains socket
before working on or moving the TV set.
Keep the mains lead away from heat sources.
Unplug the mains plug and clean it regularly. If the
plug is covered with dust and it picks up moisture, its
insulation may deteriorate, which could result in a
fire.
Notes
Do not use the supplied mains lead on any other
equipment.
Do not pinch, bend, or twist the mains lead excessively.
The core conductors may be exposed or broken.
Do not modify the mains lead.
Do not put anything heavy on the mains lead.
Do not pull on the mains lead itself when disconnecting
the mains lead.
Do not connect too many appliances to the same mains
socket.
Do not use a poor fitting mains socket.
Prohibited Usage
Do not install/use the TV set in locations,
environments or situations such as those listed
below, or the TV set may malfunction and cause a
fire, electrical shock, damage and/or injuries.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or
other vessel, inside a vehicle, in medical institutions,
unstable locations, near water, rain, moisture or smoke.
Environment:
Places that are hot, humid, or excessively dusty; where
insects may enter; where it might be exposed to mechanical
vibration, near flammable objects (candles, etc).
The TV set shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the TV.
Situation:
Do not use when your hands are wet, with the cabinet
removed, or with attachments not recommended by the
manufacturer. Disconnect the TV set from mains socket
and aerial during lightning storms.
Broken pieces:
Do not throw anything at the TV set. The screen glass
may break by the impact and cause serious injury.
If the surface of the TV set cracks, do not touch it until
you have unplugged the mains lead. Otherwise electric
shock may result.
When not in use
If you will not be using the TV set for several days, the
TV set should be disconnected from the mains for
environmental and safety reasons.
As the TV set is not disconnected from the mains when
the TV set is just turned off, pull the plug from the mains
to disconnect the TV set completely.
However, some TV sets may have features that require
the TV set to be left in standby to work correctly. The
instructions in this manual will inform you if this
applies.
For children
Do not allow children to climb on the TV set.
Keep small accessories out of the reach of children, so
that they are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the mains lead
immediately if any of the following problems occur.
Ask your dealer or Sony service centre to have it
checked by qualified service personnel.
When:
Mains lead is damaged.
Poor fitting of mains socket.
TV set is damaged by being dropped, hit or having
something thrown at it.
Any liquid or solid object falls through openings in
the cabinet.
Air circulation
is blocked.
Air circulation
is blocked.
Wall
Wall
10
GB
Precautions
Viewing the TV
View the TV in moderate light, as viewing the TV in
poor light or during long period of time, strains your
eyes.
When using headphones, adjust the volume so as to
avoid excessive levels, as hearing damage may result.
LCD Screen
Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are
effective, black dots may appear or bright points of light
(red, blue, or green) may appear constantly on the LCD
screen. This is a structural property of the LCD screen
and is not a malfunction.
Do not push or scratch the front filter, or place objects on
top of this TV set. The image may be uneven or the LCD
screen may be damaged.
If this TV set is used in a cold place, a smear may occur
in the picture or the picture may become dark. This does
not indicate a failure. These phenomena disappear as the
temperature rises.
Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
The screen and cabinet get warm when this TV set is in
use. This is not a malfunction.
The LCD screen contains a small amount of liquid
crystal. Some fluorescent tubes used in this TV set also
contain mercury. Follow your local ordinances and
regulations for disposal.
Handling and cleaning the screen surface/cabinet
of the TV set
Be sure to unplug the mains lead connected to the TV set
from mains socket before cleaning.
To avoid material degradation or screen coating
degradation, observe the following precautions.
To remove dust from the screen surface/cabinet, wipe
gently with a soft cloth. If dust is persistent, wipe with a
soft cloth slightly moistened with a diluted mild
detergent solution.
Never use any type of abrasive pad, alkaline/acid
cleaner, scouring powder, or volatile solvent, such as
alcohol, benzene, thinner or insecticide. Using such
materials or maintaining prolonged contact with rubber
or vinyl materials may result in damage to the screen
surface and cabinet material.
When adjusting the angle of the TV set, move it slowly
so as to prevent the TV set from moving or slipping off
from its table stand.
Optional Equipment
Keep optional components or any equipment emitting
electromagnetic radiation away from the TV set. Otherwise
picture distortion and/or noisy sound may occur.
Disposal of the TV set
Disposal of Old Electrical & Electronic
Equipment (Applicable in the European
Union and other European countries
with separate collection systems)
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
The recycling of materials will help to conserve natural
resources. For more detailed information about recycling
of this product, please contact your local Civic Office, your
household waste disposal service or the shop where you
purchased the product.
Disposal of waste batteries (applicable
in the European Union and other
European countries with separate
collection systems)
This symbol on the battery or on the
packaging indicates that the battery provided
with this product shall not be treated as
household waste. On certain batteries this symbol might be
used in combination with a chemical symbol. The chemical
symbols for mercury (Hg) or lead (Pb) are added if the
battery contains more than 0.0005% mercury or 0.004%
lead. By ensuring these batteries are disposed of correctly,
you will help prevent potentially negative consequences
for the environment and human health which could
otherwise be caused by inappropriate waste handling of the
battery. The recycling of the materials will help to conserve
natural resources. In case of products that for safety,
performance or data integrity reasons require a permanent
connection with an incorporated battery, this battery should
be replaced by qualified service staff only. To ensure that
the battery will be treated properly, hand over the product
at end-of-life to the applicable collection point for the
recycling of electrical and electronic equipment. For all
other batteries, please view the section on how to remove
the battery from the product safely. Hand the battery over
to the applicable collection point for the recycling of waste
batteries. For more detailed information about recycling of
this product or battery, please contact your local Civic
Office, your household waste disposal service or the shop
where you purchased the product.
11
GB
Overview of the remote
1 "/1 – TV standby
Turns the TV on and off from standby mode.
2 AUDIO
In analogue mode: Press to change the dual sound mode (page 24).
3 – Picture freeze (page 14)
Freezes the TV picture.
4 Coloured buttons (page 14, 17)
5 – Input select
Selects the input source from equipment connected to the TV sockets
(page 19).
6 F/f/G/g/
7 TOOLS (page 15, 19)
Enables you to access various viewing options and change/make
adjustments according to the source and screen format.
8 MENU (page 21)
9 Number buttons
In TV mode: Selects channels. For channel numbers 10 and above, press
the second and third digit in quick succession.
In Text mode: Enters the three digit page number to select the page.
0 – Digital Favourite list
Press to display the Digital Favourite list that you have specified (page 17).
qa Previous channel
Returns to the previous channel watched.
qs PROG +/-/ /
In TV mode: Selects the next (+) or previous (-) channel.
In Text mode (page 14): Selects the next ( ) or previous ( ) page.
qd 2 +/- – Volume
qf % – Mute the sound
qg / – Text (page 14)
qh RETURN /
Returns to the previous screen of any displayed menu.
qj GUIDE / – EPG (Digital Electronic Programme Guide) (page 16)
qk ANALOG – Analogue mode (page 13)
ql DIGITAL – Digital mode (page 13)
w; – Screen mode (page 14)
wa / – Info / Text reveal
In digital mode: Displays brief details of the programme currently being
watched.
In analogue mode: Displays information such as current channel number
and screen format.
In Text mode (page 14): Reveals hidden information (e.g. answers to a
quiz).
z
The number 5, PROG + and AUDIO buttons have tactile dots. Use the tactile dots as
references when operating the TV.
RETURN
PROG
TOOLS
AUDIO
ANALOGDIGITAL
GUIDE
MENU
12
GB
Overview of the TV buttons and indicators
1 (page 21)
2 / – Input select / OK
In TV mode: Selects the input source from
equipment connected to the TV sockets
(page 19).
In TV menu: Selects the menu or option, and
confirms the setting.
3 2 +/-/ /
In TV mode: Increases (+) or decreases (-) the
volume.
In TV menu: Moves through the options right
( ) or left ( ).
4 PROG +/-/ /
In TV mode: Selects the next (+) or previous (-)
channel.
In TV menu: Moves through the options up ( )
or down ( ).
5 1 – Power
Turns the TV on or off.
~
To disconnect the TV completely, pull the plug
from the mains.
When you turn on the TV, the power indicator
flashes in green.
6 – Picture Off / Sleep Timer indicator
Lights up in green when the picture is switched
off (page 25).
Lights up in orange when the sleep timer is set
(page 26).
7 1 – Standby indicator
Lights up in red when the TV is in standby mode.
8 " – Power indicator
Lights up in green when the TV is turned on.
9 Remote control sensor
Receives IR signals from the remote.
Do not put anything over the sensor, as its
function may be affected.
~
Make sure that the TV is completely turned off before
unplugging the mains lead. Unplugging the mains lead
while the TV is turned on may cause the indicator to
remain lit or may cause the TV to malfunction.
13
GB
Watching TV
Watching TV
Watching TV
1 Press 1 on the top edge of the TV to turn
on the TV.
When the TV is in standby mode (the 1
(standby) indicator on the TV front panel is red),
press "/1 on the remote to turn on the TV.
2 Press DIGITAL to switch to digital mode,
or ANALOG to switch to analogue mode.
The channels available vary depending on the
mode.
3 Press the number buttons or PROG +/- to
select a TV channel.
To select channel numbers 10 and above using
the number buttons, press the second and third
digits in quick succession.
To select a digital channel using the Digital
Electronic Programme Guide (EPG), see
page 16.
In digital mode
An information banner appears briefly. The
following icons may be indicated on the banner.
Additional operations
RETURN
PROG
TOOLS
AUDIO
ANALOGDIGITAL
GUIDE
MENU
3
2
2
3
: Interactive service is available (MHEG
Digital Text)
: Interactive service (MHEG Digital Text) is
currently disabled
: Radio service
: Scrambled/Subscription service
: Multiple audio languages available
: Subtitles available
: Subtitles available for the hearing impaired
: Recommended minimum age for current
programme (from 4 to 18 years)
: Parental Lock
To Do this
Adjust the volume Press 2 + (increase)/
- (decrease).
Access the
Programme index
table (in analogue
mode only)
Press . To select an analogue
channel, press
F/f, then press
.
14
GB
To access Text
Press /. Each time you press /, the display
changes cyclically as follows:
Text t Text over the TV picture (mix mode) t No
Text (exit the Text service)
To select a page, press the number buttons or /
.
To reveal hidden information, press .
z
When four coloured items appear at the bottom of the Text
page, Fastext is available. Fastext allows you to access
pages quickly and easily. Press the corresponding coloured
button to access the page.
Picture Freeze
Freezes the TV picture (e.g. to make a note of a
telephone number or recipe).
1 Press on the remote control.
2 Press again to return to normal TV
mode.
z
Not available for Component, HDMI1,
HDMI2 and PC input.
To change the screen format manually to
suit the broadcast
Press repeatedly to select the desired screen
format.
* Parts of the top and bottom of the picture may be cut off.
~
Depending on the signal, some screen formats may not
be selectable.
Some characters and/or letters at the top and the bottom
of the picture may not be visible in “Smart”.
z
You can adjust the vertical position of the picture when
selecting “Smart”, “Zoom” or “14/9”. Press
F/f to move
up or down (e.g. to read subtitles).
Smart*
Displays
conventional 4:3
broadcasts with an
imitation wide screen
effect. The 4:3 picture
is stretched to fill the
screen.
4/3
Displays
conventional 4:3
broadcasts (e.g. non-
wide screen TV) in
the correct
proportions.
Wide (KDL-32L40xx/KDL-26L40xx only)
Displays wide screen
(16:9) broadcasts in
the correct
proportions.
Zoom* (KDL-32L40xx/KDL-26L40xx only)
Displays
cinemascopic (letter
box format)
broadcasts in the
correct proportions.
14/9*
Displays 14:9
broadcasts in the
correct proportions.
As a result, black
border areas are
visible on the screen.
Subtitle*
Displays
cinemascopic (letter
box format)
broadcasts with
subtitles on the
screen.
Wide (KDL-19L40xx only)
Displays 16:9
broadcasts in the
correct proportions.
As a result, black
border areas are
visible on the screen.
Zoom (KDL-19L40xx only)
Displays 4:3
cinemascopic (letter
box format)
broadcasts in the
correct proportions.
As a result, black
border areas are
visible on the screen.
Auto
“Screen Format” is set to “Auto”, automatically changes
the screen format to suit the broadcast signal.
“Auto” is available for PAL and SECAM signals only.
15
GB
Watching TV
Using the Tools menu
Press TOOLS to display the following options when
viewing a TV programme.
Options Description
Close Closes the Tools menu.
Picture Mode See page 22.
Sound Effect See page 24.
Speaker See page 24.
Audio Language (in
digital mode only)
See page 31.
Subtitle Setting (in
digital mode only)
See page 31.
Sleep Timer See page 26.
Power Saving See page 25.
System Information (in
digital mode only)
Displays the system
information screen.
16
GB
Checking the Digital Electronic Programme
Guide (EPG) *
1 In digital mode, press GUIDE.
2 Perform the desired operation as shown
in the following table or displayed on the
screen.
* This function may not be available in some countries/regions.
~
If an age restriction for programmes has been selected, a message asking for a PIN code will appear on the screen. For details,
see “Parental Lock” on page 31.
Digital Electronic Programme Guide (EPG)
Select: Tune: Options:
Toda y
Previous Next +1 day
15:30 16:00 16:30 17:00
BBC ONE
BBC TWO
ITV 1
Channel 4
five
ITV 2
BBC THREE
Teletext
BBC FOUR
Sky Travel
UKTV History
More 4
001
002
003
004
005
006
007
009
010
011
012
013
Fri 3 Nov 15:39
To Do this
Watch a programme Press F/f/G/g to select the programme, then press .
Turn off the EPG Press GUIDE.
17
GB
Watching TV
Using the Digital Favourite list *
The Favourite feature allows you to specify up to
four lists of your favourite programmes.
1 In digital mode, press .
2 Perform the desired operation as shown
in the following table or displayed on the
screen.
* This function may not be available in some countries/regions.
Select: Store favourite
Back:
Favourite Set-up Enter programme number
---
Previous Next Favourites 2
001
002
003
004
005
006
007
008
009
010
TV3
33
3/24
K3/300
TVE1
TVE2
24H TVE
CLAN TVE
TELEDEPORTE
VEO
011
012
013
014
015
016
017
018
019
020
SETenVEO
Tienda en VEO
NET TV
CUATRO
CNN+
40 LATINO
la Sexta
Telecinco
T5 Estrellas
T5 Sport
Favourites 1
Digital Favourite list
To Do this
Create your Favourite list for the first
time
1 Press to select “Yes”.
2 Press the yellow button to select the Favourite list.
3 Press
F/f to select the channel you want to add, then press
.
Channels that are stored in the Favourite list are indicated by a
symbol.
4 Press RETURN to finish setting up.
Watch a channel
1 Press the yellow button to navigate through your Favourite
lists.
2 Press F/f to select the channel, then press .
Turn off the Favourite list
Press RETURN.
Add or remove channels in the
currently edited Favourite list
1 Press the blue button.
2 Press the yellow button to select the Favourite list you want to
edit.
3 Press
F/f to select the channel you want to add or remove,
then press .
Remove all channels from the current
Favourite list
1 Press the blue button.
2 Press the yellow button to select the Favourite list you want to
edit.
3 Press the blue button.
4 Press
G/g to select “Yes”, then press to confirm.
18
GB
Using Optional Equipment
Connecting optional equipment
You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.
AV3
PC IN
COMPONENT IN
1
AV1
AV2
2
Video game
equipment/
DVC
camcorder
Headphones
DVD player
with
component
output
DVD recorder
Decoder
VCR
Video game
equipment
DVD player
Decoder
PC
PC (HDMI output)
Blu-ray disc player
Digital video camera
DVD player
Hi-Fi audio
equipment
CAM card
19
GB
Using Optional Equipment
Viewing pictures from
connected equipment
Turn on the connected equipment, then
perform one of the following operation.
For an auto-tuned VCR (page 7)
In analogue mode, press PROG +/-, or the number
buttons, to select the video channel.
For other connected equipment
Press to display the connected equipment list.
Press F/f to select the desired input source, then
press . (The highlighted item is selected if two
seconds pass without any operation after pressing
F/
f.)
Additional operations
Using the Tools menu
Press TOOLS to display the following options when
viewing pictures from connected equipment.
Symbol on the
screen
Description
AV 1/ AV 1/
AV 1
To see the equipment connected to
A.
AV 2/ AV 2/
AV 2
To see the equipment connected to
B.
Component To see the equipment connected to
C.
HDMI1 HDMI IN 1*.
To see the equipment connected to
D.
HDMI2 HDMI IN 2*.
To see the equipment connected to
E.
If the equipment has a DVI socket,
connect the DVI socket to the HDMI
IN 2 socket through a DVI-HDMI
adaptor interface (not supplied), and
connect the equipment’s audio out
sockets to the audio in sockets in the
HDMI IN 2 sockets.
* ~
Be sure to use only an authorized HDMI cable bearing
the HDMI logo. We recommend that you use a Sony
HDMI cable.
When HDMI control compatible equipment is
connected, communication with the connected
equipment is supported. Refer to page 20 to set up this
communication.
AV3 To see the equipment connected to
H.
PC To see the equipment connected to
G.
z
It is recommended to use a PC
cable with ferrites like the
“Connector, D-sub 15” (ref. 1-793-
504-11, available in Sony Service
Centre), or equivalent.
To connect Do this
Headphones I Connect to the i socket to listen to
sound from the TV on headphones.
Conditional
Access Module
(CAM) J
To use Pay Per View services.
For details, refer to the instruction
manual supplied with your CAM. To
use the CAM, remove the “dummy”
card from the CAM slot. Turn off
the TV when inserting your CAM
into the CAM slot. When you do not
use the CAM, we recommend that
the “dummy” card be inserted and
kept in the CAM slot.
~
CAM is not supported in some
countries/regions. Check with your
authorized dealer.
Hi-Fi audio
equipment F
Connect to the audio output sockets
to listen to the sound from the
TV on Hi-Fi audio equipment.
To Do this
Return to normal
TV mode
Press DIGITAL or ANALOG.
Access the Digital
Favourites (in
digital mode only)
Press .
For details, see page 17.
Options Description
Close Closes the Tools menu.
Picture Mode (except
PC input mode)
See page 22.
Display Mode (in PC
input mode only)
See page 22.
Sound Effect See page 24.
Speaker See page 24.
Symbol on the
screen
Description
Continued
20
GB
Using control for HDMI
The control for HDMI function enables the TV to
communicate with the connected equipment that is
compatible with the function, using HDMI CEC
(Consumer Electronics Control). For example, by
connecting Sony equipment that is compatible with
control for HDMI (with HDMI cables), you can
control them together.
Be sure to connect the equipment correctly, and
make the necessary settings.
To make the control for HDMI settings
The control for HDMI settings must be set on both
the TV side and connected equipment side. See
HDMI Set-up on page 28 for the TV side settings.
For settings on the connected equipment, refer to the
operating instructions for that equipment.
Control for HDMI functions
Turns the connected equipment off interlocked
with the TV.
Turns the TV on interlocked with the connected
equipment and automatically switches the input to
the equipment when the equipment starts to play.
Horizontal Shift (in
PC input mode only)
See page 25.
Vertical Shift (in PC
input mode only)
See page 25.
Sleep Timer (except
PC input mode)
See page 26.
Power Saving See page 25.
Options Description
21
GB
Using MENU Functions
Using MENU Functions
Navigating through
menus
“MENU” allows you to enjoy various convenient
features of this TV. You can easily select channels or
inputs sources and change the settings for your TV.
1 Press MENU.
2 Press F/f to select an option, then press
.
To exit the menu, press MENU.
1 Digital Favourites*
Displays the Favourite list (page 17).
2 Analogue
Returns to the last viewed analogue channel.
3 Digital*
Returns to the last viewed digital channel.
4 Digital EPG*
Displays the Digital Electronic Programme
Guide (EPG) (page 16).
5 External Inputs
Selects equipment connected to your TV.
To watch the desired external input, select
the input source, then press .
6 Settings
Displays the “Settings” menu where most of
the advanced settings and adjustments are
performed.
1 Press F/f to select a menu icon,
then press .
2 Press
F/f/G/g to select an option or
adjust a setting, then press .
For details about settings, see page 22 to 31.
~
The options you can adjust vary depending on the
situation. Unavailable options are greyed out or
not displayed.
* This function may not be available in some
countries/regions.
RETURN TOOLS
AUDIO
ANALOGDIGITAL
GUIDE
MENU
2
1
Digital Favourites
Analogue
Digital
Digital EPG
External Inputs
Settings
Select: Enter: Exit:
MENU
22
GB
Picture Adjustment menu
You can select the options listed below on the “Picture
Adjustment” menu. To select options in “Settings”, see
“Navigating through menus” (page 21).
Picture Mode
Display Mode
(only in PC
mode)
Selects the picture mode except for PC input source.
“Vivid”: For enhanced picture contrast and sharpness.
“Standard”: For standard picture. Recommended for home entertainment.
“Cinema”: For viewing film-based content. Most suitable for viewing in a theatre-
like environment. This picture setting was developed in collaboration with Sony
Pictures Entertainment to faithfully reproduce movies as intended by their creators.
Selects the display mode for PC input source.
“Video”: For video images.
“Text”: For text, charts or tables.
Backlight
Adjusts the brightness of the backlight.
Contrast
Increases or decreases picture contrast.
Brightness
Brightens or darkens the picture.
Colour
Increases or decreases colour intensity.
Hue
Increases or decreases the green tones and red tones.
z
“Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).
Sharpness
Sharpens or softens the picture.
Colour Tone
Adjusts the whiteness of the picture.
“Cool”: Gives the white colours a blue tint.
“Neutral”: Gives the white colours a neutral tint.
“Warm”: Gives the white colours a red tint.
z
“Warm” can not be selected when you set “Picture Mode” to “Vivid”.
Select:Back: Enter: Exit:
Standard
5
Max
50
50
0
15
Warm
Medium
Medium
Picture Mode
Backlight
Contrast
Brightness
Colour
Hue
Sharpness
Colour Tone
Noise Reduction
MPEG Noise Reduction
Reset
Picture Adjustment
23
GB
Using MENU Functions
~
“Brightness”, “Colour”, “Hue” and “Sharpness” are not available when “Picture Mode” is set to “Vivid” or when “Display
Mode” is set to “text”.
Noise Reduction
Reduces the picture noise (snowy picture) in a weak broadcast signal.
“High/Medium/Low”: Modifies the effect of the noise reduction.
“Off”: Turns off the “Noise Reduction” feature.
MPEG Noise
Reduction
Reduces the picture noise in MPEG-compressed video.
Reset
Resets all “Picture Adjustment” settings except “Picture Mode” and “Display Mode”
(only in PC mode) to the factory settings.
24
GB
Sound Adjustment menu
~
“Sound Effect”, “Surround”, “Treble”, “Bass”, “Balance”, “Reset” and “Auto Volume” are not available when “Speaker” is
set to “Audio System”.
You can select the options listed below on the “Sound
Adjustment” menu. To select options in “Settings”, see
“Navigating through menus” (page 21).
Sound Effect
Selects the sound mode.
“Standard”: Enhances clarity, detail, and sound presence.
“Dynamic”: Intensifies clarity and sound presence for better intelligibility and
musical realism.
“Clear Voice”: Makes voice sound clearer.
Surround
Selects the surround mode.
“Surround”: For surround sound (for stereo programmes only).
“Simulated Stereo”: Adds a surround-like effect to mono programs.
“Off”: For normal stereo or mono reception.
Treble
Adjusts higher-pitched sounds.
Bass
Adjusts lower-pitched sounds.
Balance
Emphasizes left or right speaker balance.
Reset
Resets all the “Sound Adjustment” settings to the factory settings.
Dual Sound
Selects the sound from the speaker for a stereo or bilingual broadcast.
“Stereo”, “Mono”: For a stereo broadcast.
“A”/“B”/“Mono”: For a bilingual broadcast, select “A” for sound channel 1, “B”
for sound channel 2, or “Mono” for a mono channel, if available.
z
If you select other equipment connected to the TV, set “Dual Sound” to “Stereo”, “A” or “B”.
Auto Volume
Keeps a constant volume level even when volume level gaps occur (e.g., adverts tend
to be louder than programmes).
Speaker
Turns on/off the TV’s internal speakers.
“TV Speaker”: The TV speakers are turned on in order to listen to the TV’s sound
through the TV speakers.
“Audio System”: The TV speakers are turned off in order to listen to the TV’s sound
only through your external audio equipment connected to the audio output sockets.
Sound Effect
Surround
Treble
Bass
Balance
Reset
Dual Sound
Auto Volume
Speaker
Sound Effect
Surround
Treble
Bass
Balance
Reset
Dual Sound
Auto Volume
Speaker
Standard
Off
0
0
0
Mono
On
TV Speaker
Select:Back: Enter: Exit:
Sound Adjustment
25
GB
Using MENU Functions
Features menu
You can select the options listed below on the “Features”
menu. To select options in “Settings”, see “Navigating
through menus” (page 21).
Screen
Screen
(only in PC
mode)
Changes the screen format.
Screen Format
For details about the screen format, see page 14.
z
“Auto” is available for PAL and SECAM signals only.
“Normal”: Displays the picture in its original size.
“Full”: Enlarges the picture to fill the display area.
Power Saving
Selects the power saving mode to reduce the power consumption of the TV.
“Standard”: Default settings.
“Reduce”: Reduces the power consumption of the TV.
“Picture Off”: Switches off the picture. You can listen to the sound with the picture
off.
RGB Centre
Adjusts the horizontal picture position so that the picture is in the middle of the
screen.
z
This option is only available if an RGB source has been connected to the Scarts connectors
/ / AV1
or / / AV2 on the rear of the TV.
PC Adjustment
Customizes the TV screen as a PC monitor.
z
This option is only available if a PC signal is received.
“Phase”: Adjusts the screen when a part of a displayed text or image is not clear.
“Pitch”: Enlarges or shrinkes the screen size horizontally.
“Horizontal Shift”: Moves the screen to the left or to the right.
“Vertical Shift”: Moves the screen up or down.
“Power Saving”: When this is set to “On,” turns to standby mode if no PC signal is
received. To return to the TV, press ?/1.
“Reset”: Resets to the factory settings.
Screen
Power Saving
Timer
Standard
Select:Back: Enter: Exit:
Features
Continued
26
GB
Timer
Sets the timer to turn off the TV.
Sleep Timer
Sets a period of time after which the TV automatically switches itself into standby
mode.
When the “Sleep Timer” is activated, the (Sleep Timer) indicator on the TV
front panel lights up in orange.
z
When you turn off the TV and turn it on again, “Sleep Timer” is reset to “Off”.
A notification message appears on the screen one minute before the TV switches to standby
mode.
27
GB
Using MENU Functions
Set-up menu
You can select the options listed below on the “Set-up”
menu. To select options in “Settings”, see “Navigating
through menus” (page 21).
Auto Start-up
Starts the initial set-up to select the language, country/region and location, and tune
in all available digital and analogue channels. Usually, you do not need to do this
operation because the language and country/region will have been selected and
channels already tuned when the TV was first installed (page 7). However, this
option allows you to repeat the process (e.g., to retune the TV after moving house).
Language
Selects the language in which the menus are displayed.
Auto Tuning
(Only in
analogue mode)
Tunes in all the available analogue channels.
Usually you do not need to do this operation because the channels are already tuned
when the TV was first installed (page 7). However, this option allows you to repeat
the process (e.g., to retune the TV after moving house, or to search for new channels
that have been launched by broadcasters).
Programme
Sorting
(Only in
analogue mode)
Changes the order in which the analogue channels are stored on the TV.
1 Press
F/f to select the channel you want to move to a new position,
then press
g.
2 Press F/f to select the new position for your channel, then press .
AV Preset
Assigns a name to any equipment connected to the side and rear sockets. The name
will be displayed briefly on the screen when the equipment is selected. You can skip
an input source that is not connected to any equipment.
1 Press
F/f to select the desired input source, then press .
2 Press
F/f to select the desired option below, then press .
AV1 (or AV2/AV3/HDMI1/HDMI2/Component/PC), VIDEO, DVD, CABLE,
GAME, CAM, SAT
: Uses one of the preset labels to assign a name to connected
equipment.
Edit”: Creates your own label.
1 Press F/f to select the desired letter or number (“_” for a blank
space), then press g.
If you input a wrong character
Press G/g to select the wrong character. Then, press F/f to select the correct
character.
2 Repeat the procedure in step 1 until the name is completed, then
press .
Auto Start-up
Language
Auto Tuning
Programme Sorting
English
AV Preset
HDMI Set-up
Sound Offset
Manual Programme Preset
Digital Set-up
Select:Back: Enter: Exit:
Set-up
Continued
28
GB
HDMI Set-up
Allows the TV to communicate with equipment that is compatible with the control
for HDMI function, and connected to the HDMI sockets of the TV. Note that
communication settings must also be made on the connected equipment.
“Control for HDMI”: Sets whether or not to link the operations of the TV and the
connected equipment that is compatible with control for HDMI.
“Auto Devices Off”: When this is set to “On”, the connected equipment that is
compatible with control for HDMI turns off when you switch the TV to standby
mode using the remote.
“Auto TV On”: When this is set to “On”, the TV turns on when you turn on the
connected equipment that is compatible with control for HDMI.
“Device List Update”: Creates or updates the “HDMI Device List”. Up to 11
compatible equipment items can be connected, and up to 5 equipment items can be
connected to a single socket. Be sure to update the “HDMI Device List” when you
change the connections or settings.
“HDMI Device List”: Displays a list of connected equipment that is compatible
with control for HDMI.
Sound Offset
Sets an independent volume level to each equipment connected to the TV.
Manual
Programme
Preset
(Only in
analogue mode)
Changes the available analogue channel setting.
Press
F/f to select the programme number you want to modify. Then, press .
System
Presets programme channels manually.
1 Press
F/f to select “System”, then press .
2 Press F/f to select one of the following TV broadcast systems, then
press
G.
B/G: For western European countries/regions
I: For the United Kingdom
D/K: For eastern European countries/regions
L: For France
~
Depending on the country/region selected for “Country” (page 6), this option may not be
available.
Channel
1 Press
F/f to select “Channel”, then press .
2 Press F/f to select “S” (for cable channels) or “C” (for terrestrial
channels), then press
g.
3 Tune the channels as follows:
If you do not know the channel number (frequency)
Press F/f to search for the next available channel. When a channel has been found,
the search will stop. To continue searching, press
F/f.
If you know the channel number (frequency)
Press the number buttons to enter the channel number of the broadcast you want or
your VCR channel number.
4 Press to jump to “Confirm”, then press .
Repeat the procedure above to preset other channels manually.
Label
Assigns a name of your choice, up to five letters or numbers, to the selected channel.
AFT
Allows you to fine-tune the selected programme number manually if you feel that a
slight tuning adjustment will improve the picture quality.
29
GB
Using MENU Functions
Audio Filter
Improves the sound for individual channels in the case of distortion in mono
broadcasts. Sometimes a non-standard broadcast signal can cause sound distortion or
intermittent sound muting when watching mono programmes.
If you do not experience any sound distortion, we recommend that you leave this
option set to the factory setting “Off”.
~
“Audio Filter” is not available when “System” is set to “L”.
Skip
Skips unused analogue channels when you press PROG +/- to select channels. (You
can still select a skipped channel using the number buttons.)
Confirm
Saves changes made to the “
Manual Programme Preset” settings.
30
GB
Digital Set-up menu
You can select the options listed below on the “Digital
Set-up” menu. Then press F/f to select the “Digital
Tuning” or “Digital Set-up”. To select options in
“Settings”, see “Navigating through menus” (page 21).
~
Some functions may not be available in some countries/regions.
Digital Tuning
Digital Auto Tuning
Tunes in the available digital channels.
This option allows you to retune the TV after moving house, or to search for new
channels that have been launched by broadcasters. Press .
Programme List Edit
Removes any unwanted digital channels stored on the TV, and changes the order of
the digital channels stored on the TV.
1 Press
F/f to select the channel you want to remove or move to a new
position.
Press the number buttons to enter the known three-digit programme number of the
broadcast you want.
2 Remove or change the order of the digital channels as follows:
To remove the digital channel
Press . After a confirmation message appears, press
G
to select “Yes”, then press .
To change the order of the digital channels
Press g, then press F/f to select the new position for the channel and press G.
3 Press RETURN.
Digital Manual Tuning
Tunes the digital channels manually.
1 Press the number button to select the channel number you want to
manually tune, then press
F/f to tune the channel.
2 When the available channels are found, press
to store programmes.
Repeat the above procedure to manually tune other channels.
Auto Start-up
Language
Auto Tuning
Programme Sorting
English
AV Preset
HDMI Set-up
Sound Offset
Manual Programme Preset
Digital Set-up
Select:Back: Enter: Exit:
Set-up
31
GB
Using MENU Functions
Digital Set-up
Subtitle Set-up
“Subtitle Setting”: When “For Hard Of Hearing” is selected, some visual aids may
also be displayed with the subtitles (if TV channels broadcast such information).
“Subtitle Language”: Selects which language subtitles are displayed in.
Audio Set-up
“Audio Type”: Switches to broadcast for the hearing impaired when “For Hard Of
Hearing” is selected.
“Audio Language”: Selects the language used for a programme. Some digital
channels may broadcast several audio languages for a programme.
“Audio Description”: Provides audio description (narration) of visual information
if TV channels broadcast such information.
“Mixing Level”: Adjusts the TV main audio and Audio Description output levels.
z
This option is only available when “Audio Description” is set to “On”.
Banner Mode
“Basic”: Displays programme information with a digital banner.
“Full”: Displays programme information with a digital banner, and displays detailed
programme information below that banner.
Parental Lock
Sets an age restriction for programmes. Any programme that exceeds the age
restriction can only be watched after a PIN Code is entered correctly.
1 Press the number buttons to enter your existing PIN code.
If you have not previously set a PIN, a PIN code entry screen appears. Follow the
instructions of “PIN Code” below.
2 Press F/f to select the age restriction or “None” (for unrestricted
watching), then press .
3 Press RETURN.
PIN Code
To set your PIN for the first time
1 Press the number buttons to enter the new PIN code.
2 Press RETURN.
To change your PIN
1 Press the number buttons to enter your existing PIN code.
2 Press the number buttons to enter the new PIN code.
3 Press RETURN.
z
PIN code 9999 is always accepted.
Technical Set-up
“Auto Service Update”: Enables the TV to detect and store new digital services as
they become available.
“Software Download”: Enables the TV to automatically receive software updates,
free through your existing aerial (when issued). Sony recommends that this option is
set to “On” at all times. If you do not want your software to be updated, set this option
to “Off”.
“System Information”: Displays the current software version and the signal level.
“Time Zone”: Allows you to manually select the time zone you are in, if it is not the
same as the default time zone setting for your country/region.
“Auto DST”: Sets whether or not to automatically switch between summer time and
winter time.
“On”: Automatically switches between summer time and winter time according to the
calendar.
“Off”: The time is displayed according to the time difference set by “Time Zone”.
CA Module Set-up
Allows you to access a pay TV service once you obtain a Conditional Access Module (CAM)
and a view card. See page 18 for the location of the (PCMCIA) socket.
32
GB
Additional Information
Installing the Accessories (Wall-Mount Bracket)
To Customers:
For product protection and safety reasons, Sony strongly recommends that installing of your TV be
performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and examination of this product.
Your TV can be installed using the Wall-Mount Bracket SU-WL500 or SU-WL100 (sold separately).
Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the installation.
Refer to “Detaching the Table-Top Stand from the TV” (page 7).
Refer to “TV installation dimensions table” (page 33).
Refer to “Screw and Hook locations diagram/table” (page 34).
~
Place the TV on the Table-Top Stand, when securing the Mounting Hook.
SU-WL500 for KDL-32L40xx
SU-WL100 for KDL-26L40xx/KDL-19L40xx
Sufficient expertise is required for installing this product, especially to determine the strength of the wall for
withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers
or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any
damage or injury caused by mishandling or improper installation.
Screw
(+PSW6 × 16)
Mounting Hook
Square hole
20
15
1
0
5
0
20
15
1
0
5
0
Screw
(+PSW4 × 12)
Mounting Hook
33
GB
Additional Information
KDL-32L40xx
KDL-26L40xx
KDL-19L40xx
Unit: mm
Figures in the above table may differ slightly depending on the installation.
The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of
the TV. Refer to “Specifications” (page 35) for its weight.
TV installation dimensions table
Model Name
Display dimensions
Screen centre
dimension
Length for each mounting angle
Angle (0°) Angle (20°)
AB C DEFGH
KDL-32L40xx 807 548 172 485 167 304 532 513
KDL-26L40xx 674 470 92 352 153 258 456 357
KDL-19L40xx 479 376 125 339 136 215 362 340
Screen centre point
Screen centre point
Screen centre point
WARNING
Continued
34
GB
KDL-32L40xx
* Hook position “a” and “b” cannot be used for the model in the table above.
KDL-26L40xx/KDL-19L40xx
Screw and Hook locations diagram/table
Model Name Screw location Hook location
KDL-32L40xx e, g c
Model Name Hook location
KDL-26L40xx a
KDL-19L40xx b
Screw location Hook location
b*
a*
c
b
a
35
GB
Additional Information
Specifications
*
1
AV1 outputs available only analogue TV.
*
2
AV2 outputs watching screen (except PC, HDMI1,2, Component 1080i).
*
3
Specified standby power is reached after the TV finishes necessary internal processes.
Design and specifications are subject to change without notice.
Model name KDL-32L40xx KDL-26L40xx KDL-19L40xx
System
Panel System
LCD (Liquid Crystal Display) Panel
TV System
Depending on your country/region selection
Analogue: B/G/H, D/K, L, I
Digital: DVB-T
Colour/Video System
Analogue: PAL, SECAM, NTSC 3.58, 4.43 (only Video In)
Digital: MPEG-2 MP@ML
Channel Coverage
Analogue:48.25 - 855.25 MHz
Digital: VHF Band III (177.5 - 226.5 MHz)/UHF E21 - E69 (474 - 858 MHz)
Sound Output
10 W + 10 W (RMS) 5 W + 5 W (RMS)
Input/Output jacks
Aerial
75 ohm external terminal for VHF/UHF
/ / AV1*
1
21-pin scart connector including audio/video input, RGB input, S-Video input, and Analog TV audio/
video output.
/ / AV2*
2
21-pin scart connector including audio/video input, RGB input, S-Video input, and audio/video output.
COMPONENT IN
Supported formats: 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync/P
B/CB: 0.7 Vp-p, 75 ohms/
P
R/CR: 0.7 Vp-p, 75 ohms
COMPONENT IN
Audio input (phono jacks)
HDMI IN 1, 2
Video: 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits
PC (see table)
Analogue audio (minijack) (HDMI IN 2 only)
AV3
Video input (phono jack)
AV3
Audio input (phono jacks)
Audio output (Left/Right) (phono jacks)
PC IN
PC Input (15 Dsub) (see page 36)
G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms, non Sync on Green/
R: 0.7 Vp-p, 75 ohms, non Sync on Green
PC audio input (minijack)
i
Headphones jack
CAM (Conditional Access Module) slot
Power and others
Power Requirements
220–240 V AC, 50 Hz
Screen Size
32 inches (Approx. 81.3 cm
measured diagonally)
26 inches (Approx. 66.1 cm
measured diagonally)
19 inches (Approx. 48.1 cm
measured diagonally)
Display Resolution
1,366 dots (horizontal) × 768 lines (vertical) 1,680 dots (horizontal) × 1,050
lines (vertical)
Power Consumption
155 W 98 W 48 W
Standby Power Consumption*
3
0.5 W or less 0.5 W or less 1 W or less
Dimensions
(w × h × d)
(with stand)
Approx. 80.7 × 58.5 × 24.2 cm Approx. 67.4 × 51.0 × 24.2 cm Approx. 47.9 × 41.3 × 19.1 cm
(without stand)
Approx. 80.7 × 54.8 × 10.1 cm Approx. 67.4 × 47.0 × 9.5 cm Approx. 47.9 × 37.6 × 7.6 cm
Mass (with stand)
Approx. 15.0 kg Approx. 11.7 kg Approx. 5.8 kg
(without stand)
Approx. 13.0 kg Approx. 9.5 kg Approx. 5.3 kg
Supplied Accessories
Refer to “1: Checking the accessories” on page 4.
Optional Accessories
See “Installing the Accessories (Wall-Mount Bracket)” on page 32.
36
GB
PC Input Signal Reference Chart for PC IN
This TV’s PC input does not support Sync on Green or Composite Sync.
This TV’s PC input does not support interlaced signals.
This TV’s PC input supports signals in the above chart with a 60 Hz vertical frequency.
PC Input Signal Reference Chart for HDMI IN 1, 2
Signals Horizontal (Pixel) Vertical (Line)
Horizontal
frequency
(kHz)
Vertical
frequency (Hz)
Standard
VGA 640 480 31.5 60 VGA
SVGA 800 600 37.9 60 VESA Guidelines
XGA 1024 768 48.4 60 VESA Guidelines
WXGA 1280 768 47.8 60 VESA
Signals Horizontal (Pixel) Vertical (Line)
Horizontal
frequency
(kHz)
Vertical
frequency (Hz)
Standard
VGA 640 480 31.5 60 VGA
SVGA 800 600 37.9 60 VESA Guidelines
XGA 1024 768 48.4 60 VESA Guidelines
WXGA 1280 768 47.4 60 VESA
WXGA 1280 768 47.8 60 VESA
WXGA 1360 768 47.7 60 VESA
37
GB
Additional Information
Troubleshooting
Check whether the 1 (standby) indicator is
flashing in red.
When it is flashing
The self-diagnosis function is activated.
Press 1 on the top edge of the TV to turn it off,
disconnect the mains lead, and inform your dealer or
Sony service centre.
When it is not flashing
1 Check the items in the tables below.
2 If the problem still persists, have your TV
serviced by qualified service personnel.
Picture
No picture (screen is dark) and no sound
Check the aerial connection.
Connect the TV to the mains, and press 1 on the top
edge of the TV.
If the 1 (standby) indicator lights up in red, press "/1.
No picture or no menu information from
equipment connected to the scart connector
Press to display the connected equipment list, then
select the desired input.
Check the connection between the optional equipment
and the TV.
Double images or ghosting
Check the aerial connection.
Check the aerial location and direction.
Only snow and noise appear on the screen
Check if the aerial is broken or bent.
Check if the aerial has reached the end of its serviceable
life (three to five years in normal use, one to two years
at the seaside).
Distorted picture (dotted lines or stripes)
Keep the TV away from electrical noise sources such as
cars, motorcycles, hair-dryers or optical equipment.
When installing optional equipment, leave some space
between the optional equipment and the TV.
Check the aerial connection.
Keep the aerial cable away from other connecting
cables.
Picture or sound noise when viewing a TV
channel
Adjust “AFT” (Automatic Fine Tuning) to obtain better
picture reception (page 28).
Some tiny black points and/or bright points
appear on the screen
The picture of a display unit is composed of pixels. Tiny
black points and/or bright points (pixels) on the screen
do not indicate a malfunction.
No colour on programmes
Select “Reset” (page 23).
No colour or irregular colour when viewing a
signal from the COMPONENT IN sockets
Check the connection of the COMPONENT IN
sockets and check if each sockets are firmly seated in
their respective sockets.
Sound
No sound, but good picture
Press 2 + or % (Mute).
Check if the “Speaker” is set to “TV Speaker” (page 24).
Channels
The desired channel cannot be selected
Switch between digital and analogue mode and select
the desired digital/analogue channel.
Some channels are blank
Scrambled/Subscription only channel. Subscribe to the
pay TV service.
Channel is used only for data (no picture or sound).
Contact the broadcaster for transmission details.
Digital channels are not displayed
Contact a local installer to find out if digital
transmissions are provided in your area.
Upgrade to a higher gain aerial.
General
The TV turns off automatically (the TV enters
standby mode)
Check if the “Sleep Timer” is activated (page 26).
If no signal is received and no operation is performed in
the TV mode for 15 minutes, the TV automatically
switches to standby mode.
The remote does not function
Replace the batteries.
HDMI equipment does not appear on “HDMI
Device List”
Check that your equipment is compatible with control
for HDMI.
Printed in Hungary
For useful information about Sony products
Instructions on “Installing the Wall-Mount Bracket” are not supplied
in the form of a separate leaflet with this TV. These installation
instructions are included within this TVs instructions manual.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sony KDL-32L4000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sony KDL-32L4000 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Sony KDL-32L4000

Sony KDL-32L4000 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano, Português, Espanôl - 259 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info