680556
72
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
72
46900V001_Rev-D_EN
16. Troubleshooting
16.4 Troubleshooting table
Problem Possible cause Test/check Remedy
The operator opens
the door when the
transmitter or control
device is actuated but
does not close it.
Photocell and safety
device interrupted
Check photocell and safety
devices
Remove obstacle
The photocell must be aligned
Have it checked and replaced by a
qualiedspecialist
Automatic closing
function activated
Wait to see whether the
operator starts automatically
after 30 seconds
Automatic closing function
deactivated
Have the cause corrected by a
trained electrician
Operator cannot be
operated with the
control device.
No power Check power supply Check the power socket with a
different device, for example by
plugging in a lamp
Limit switch on motor
carriage defective
Unlock operator and push
motor carriage to the centre of
the track
Lock operator
Actuate transmitter
If the operator still closes the
door but does not open it,
the limit switch is defective
Have the limit switch replaced by a
qualiedspecialist
The operator was
unlocked by the
emergency release
mechanism
Check that the door can be
moved manually
Pull the emergency release handle
to lock the operator
Control device
incorrectly connected to
the operator
Check function of operator
with a transmitter
Check wiring, correct if necessary
Transmitter defective Operator cannot be started
with the transmitter
Check transmitter power supply
If necessary, replace the battery of
the transmitter
If necessary, replace the
transmitter with a new one
Operator defective Operator cannot be started
with the transmitter or the
connected control device
Have operator repaired or
replacedbyaqualiedspecialist
Electrical supply voltage
outside the approved
range
Have the mains voltage
checked by a trained
electrician
Have the cause corrected by a
trained electrician
When a button on
the transmitter is
pressed, the door
does not open or
close.
Transmitter not
programmed
Radio LED does not light
up when the transmitter is
operated
Programme transmitter
Battery in the
transmitterisat
Replace the battery of the
transmitter
Transmitter defective LED on transmitter does not
light up
Replace transmitter
Radio command
cannot be
programmed.
Memory full All four LEDs for radio blink
cyclically for about 3 seconds
Memory full, see Chapter
"10.6 Information on Memo"
and "10.8 Deleting a transmitter
button from the radio channel"
MEMO Identier error Incorrect MEMO • All four LEDs blink cyclically
for a short time and then
go out for a long time. The
operator lighting of the motor
carriage blinks 4 times short
and 4 times long.
Disconnect operator from the
power supply, unplug Memo,
re-supply operator with power
MEMO device type
error
System error All four LEDs blink cyclically
for a long time and then go
out for a short time. If voltage
is present, the operator
lighting of the motor carriage
blinks an additional four times.
Memo can be deleted via
the Radio button, see Chapter
"10.8 Deleting a transmitter
button from the radio channel"
72

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer S 9110 base plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer S 9110 base plus in de taal/talen: Engels als bijlage per email.

De handleiding is 8,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer S 9110 base plus

Sommer S 9110 base plus Installatiehandleiding - Nederlands - 80 pagina's

Sommer S 9110 base plus Installatiehandleiding - Deutsch - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info