680556
51
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
51
46900V001_Rev-D_EN
11. Connections and special functions of the ceiling
control unit
11.3 Setting the DIP switches on the
ceiling control unit
Special functions can be set with the DIP switches on the
ceiling control unit.
All DIP switches are set to OFF by default.
NOTE
Do not use a metal object to set the
DIP switches, because this may damage
the DIP switches or the circuit board.
Use a suitable tool to set the DIP switches,
such as a at, thin plastic object.
DIP switches
on the ceiling
control unit ON
OFF
1
ON
1
23
4
"Conex"
additional
circuit board
T1denes
door OPEN
T2denes
door CLOSE
"Conex"
additional
circuit board
T1 pulse
sequence
T2 lighting
function/partial
opening
2
ON
1234
Relay
(MUFU) trips
during door
movement
and if the door
is not closed*
Relay (MUFU)
lighting
function
3
ON
1234
Continuous
power to the
complete
system
activated
Power-
saving mode
activated
4
ON
1234
COM and
Signal
activated
as button
input (partial
opening)
COM and
Signal
activated as
safety contact
for photocell
* e.g.: door status display
11.4 Button 2 for partial opening
If required, another button can be connected for partial
opening operation. After installation of the keypad, all
settings must be made on the ceiling control unit and the
motor carriage.
NOTE
The control unit cover is connected to the
circuit board of the ceiling control unit via
a connection cable. If an accumulator has
been installed, it is also connected to the
circuit board.
Carefully remove the control unit cover
and disconnect the connections to prevent
damage to the ceiling control unit.
INFORMATION
If button 2 (partial opening) is used,
a photocell cannot be connected.
The automatic closing operating mode is
then not possible.
Installing the keypad
1. When installing the potential-free keypad, select a
suitable position at a height of at least 1.6 m.
2. Install the keypad.
3. The keyboard cable for the ceiling control unit must
be firmly secured to prevent displacement.
Installation of the control cable and settings on the
ceiling control unit
1. Disconnect the operator from the mains voltage.
Check that the operator is disconnected from the
power supply.
2. Unscrew the cover from the ceiling control unit.
3. If an accumulator is used, it must also be
disconnected, see Chapter "11.11 Installing and
removing the accumulator".
4. Remove the control unit cover.
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
G
N
D
+24
V
ON
1234
Fig. 5 Fig. 6
51

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer S 9110 base plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer S 9110 base plus in de taal/talen: Engels als bijlage per email.

De handleiding is 8,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer S 9110 base plus

Sommer S 9110 base plus Installatiehandleiding - Nederlands - 80 pagina's

Sommer S 9110 base plus Installatiehandleiding - Deutsch - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info