680556
46
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
46
46900V001_Rev-D_EN
10. Connections and special functions of the motor
carriage
INFORMATION
The lighting function or partial opening can
be operated.
1. Set DIP switch 2 on the motor carriage to OFF.
2. Press the radio button repeatedly to select the radio
channel CH 2. Programme the lighting function on
the desired transmitter button.
The lighting function is available.
The operator lighting on the motor carriage can be
switched on and off with the transmitter button.
INFORMATION
If the operator lighting is not switched off
manually, it switches off automatically after
60 minutes. This value can be changed via
SOMlink and a WiFi-enabled device.
Other lights and functions are available with the Lumi
+
and the relay accessories.
The Lumi
+
is an LED strip with 12 LEDs (24V, 7W). It can
be attached to the ceiling control unit as supplemental
lighting.
Parallel to the operator lighting, the Lumi+ and relay
switch on with the "Start" impulse. The light burning time
set at the factory is 180 seconds. If the light function
is activated via the CH 2 radio channel, the operator
lighting, the Lumi+ and the relay can also be switched
on and off separately. This does not trigger a travel
command.
After 60 minutes, the operator lighting, the Lumi
+
or the
relay are switched off automatically.
The Lumi
+
and the relay accessories can be purchased
from your specialist dealer or at:
www.sommer.eu
10.17 Setting partial opening
This function allows you to set a desired partial opening.
The door then does not open completely, but only to the
set door position.
Example:
A side-opening sectional door can be opened to allow a
person to pass through. The partial opening can only be
used via radio control system or button 2, see Chapter
"11.4 Button 2 for partial opening".
INFORMATION
The specied partial opening can be from
any position of the door.
INFORMATION
A partial opening function can only be
programmed with automatic closing
deactivated.
1. Close the door completely up to the door CLOSE
end position.
2. Press the radio button repeatedly to select radio
channel CH 2 and to program the partial opening
function to the desired transmitter button.
3. Set DIP switch 2 on the motor carriage to ON.
4. Press the desired button on the transmitter for the
partial opening function.
The door moves in door OPEN direction.
5. When the door reaches the desired partial opening
position, press the button on the transmitter again.
The door stops at the desired position.
10.18 Deleting partial opening
1. Set DIP switch 2 on the motor carriage to OFF.
2. Open the door completely up to the door OPEN end
position.
Partial opening is deleted.
To program a new position, see Chapter "10.17 Setting
partial opening".
10.19 Wicket door safety device
The wicket door safety device prevents operation of the
door with open wicket doors.
1. The wicket door safety device must be installed
so that the switch reliably detects the open door.
Do not install the wicket door safety device on the
hinge side.
2. Connect the wicket door safety device on the
terminal block on the motor carriage. The contact
command is at 12 V DC, 10 mA. The normally closed
contact is potential-free.
3. Check the function.
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer S 9110 base plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer S 9110 base plus in de taal/talen: Engels als bijlage per email.

De handleiding is 8,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer S 9110 base plus

Sommer S 9110 base plus Installatiehandleiding - Nederlands - 80 pagina's

Sommer S 9110 base plus Installatiehandleiding - Deutsch - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info