680825
68
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
68
S10564-00001_Rev-A_EN
12. Function test/Final test
12.1 Testing obstacle detection
Observe in particular the following safety instructions for
this chapter.
After commissioning the operator, the force measurement
of the operator must be checked with a force
measurement device and an obstacle recognition test
must be performed.
WARNING
Danger of entrapment!
If the force setting is too high, persons
or animals in the movement area of the
door may be trapped and pulled along
with the door.
Severe injuries or death may result.
The force setting is relevant to safety
and must be carefully checked and
if necessary adjusted by qualied
specialists.
WARNING
Danger of crushing and shearing!
If the door moves with persons or
animals in the movement area, crushing
and shearing injuries may be caused
by the mechanism and safety edges of
the door.
The power cut-off does not operate
below 50 mm.
The photo eye function must be tested
once a month.
Only use the operator in direct view of
the door.
All danger zones must be visible during
the entire door operation.
Always keep the moving door in sight.
Persons or animals must not be in the
range of movement of the door.
Never put your hand near the door
or moving parts when it is moving.
In particular, do not reach into the
moving push arm.
Do not reach into the ceiling mounting
unit when the carriage runs along the
track.
Only pass through the door only once
it is completely open and the trafc light
has given access authorisation.
NOTE
Observe the national standards, guidelines
and regulations for cut-off of the operating
forces.
NOTE
The obstacle detection must be tested
once a month to prevent damage to the
operator.
INFORMATION
After installation of the operator, the
person responsible for the installation
of the operator must complete an
EC Declaration of Conformity for the door
system in accordance with Machinery
Directive 2006/42/EC and apply the
CE mark and a type plate to the door
system. This also applies if the operator
is retrotted to a manually operated door.
All documents as well as the inspection
book for the door, the installation and
operating manual and the handover
protocol must be retained by the user.
INFORMATION
Reversing: The operator stops on contact
with an obstacle and then moves a bit
in the opposite direction to release the
obstacle.
In the automatic closing function the
door opens completely if an obstacle is
detected.
INFORMATION
The operating forces can be modied
and adjusted with SOMlink and a WLAN-
enabled device. For more information ask
your specialist dealer.
After successful testing of the force settings, the obstacle
recognition and the functions, the qualified specialist
must attach the CE mark and type place on the door
system.
The operator must reverse in the door OPEN direction
when it is loaded with a weight of 20 kg. The weight is
fastened in the centre of the bottom edge of the door for
this purpose.
The door must immediately stop and reverse during the
door CLOSE movement if it hits a 50-mm-high obstacle.
1. Open the door with the operator.
2. Place a 50-mm-high object in the centre of the door.
68

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer S 9060 Tiga bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer S 9060 Tiga in de taal/talen: Engels als bijlage per email.

De handleiding is 28,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer S 9060 Tiga

Sommer S 9060 Tiga Gebruiksaanwijzing - Nederlands - 96 pagina's

Sommer S 9060 Tiga Gebruiksaanwijzing - Deutsch - 96 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info