474213
22
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
Operation and Handling
21
Interim stop
If an interim stop occurs due to the operation of a push-button or the
manual remote control, the drive unit stops immediately. The next command
given sends the drive in the opposite direction. See 'Pulse Sequence of
Door Movement' section.
Safety stop 1
(automatic force cut-off)
When the automatic force cut-off is activated, the drive stops or reverses.
When the next command is given, the drive moves in the opposite direction.
See 'Pulse Sequence of Door Movement' section.
- Safety stop when door closes - door reverses
- Safety stop when door opens - door stops.
Safety stop 2
(automatic force cut-off)
When the safety input is tripped (e.g. someone crosses light barrier), the
drive stops, reverses or opens, depending on the given DIP switch setting:
- DIP switch 1 + 3
See 'Obstacle Recognition' section for given drive type.
When the next command is given, the drive moves in the opposite direction.
See 'Pulse Sequence of Door Movement' section.
Default settings:
- safety input tripped when door closes:
door reverses
- safety input tripped when door opens:
no response (door opens).
Overload protection
If the drive mechanism is subjected to excessive strain when opening or
closing the door, this is recognised by the control unit which then stops the
drive mechanism. After approx. 20 seconds or a control unit reset, the
control unit deactivates the overload protection.
The drive mechanism can now recommence normal operation.
Operation following a power failure
The force values remain saved even during a power failure. The first
movement of the unit following a power cut is always door OPEN.
Radio remote control receiver
Homelink compatible!
If your vehicle is equipped with a Homelink system (version 7),
you can reach our drive/radio receiver at 868.6 MHz. With holder
Homelink systems, you must use a different frequency (40.685 or
434.42 MHz). For more information, please visit:
"http://www.eurohomelink.com"
To ensure safe operation, local safety regulations relevant to the
equipment concerned must be observed! Information regarding this can
be obtained from electricity suppliers, the VDE and employers' liability
insurance associations.
The operator of this radio-controlled equipment is in no way protected
from interference from other telecommunications systems and facilities
(e.g. other radio-controlled equipment that is licensed to operate at the
same frequency range).
Try replacing the batteries should reception problems be encountered.
Description of display and
push-buttons
1 Setting button
Puts radio receiver in a given operating mode:
self-learn, delete and normal
2 Internal aerial
3 LED
Display which channel has been selected.
3.1 LED channel 1
3.2 LED channel 2
4 Connection for external aerial (6)
If the radio range of the internal aerial is not sufficient, you have
the option to connect an external aerial.
5 Manual remote control button
6 External aerial
Teaching in manual remote control
Press setting button (1)
- Press 1x for channel 1; LED (3.1) lights up
- Press 2x for channel 2; LED (3.2) lights up
- If no radio code is transmitted within 10 seconds, the receiver
switches back to normal operating mode.
- Interrupting setting mode: press setting button (1) as often as
required to put out all LEDs
Press and hold desired hand-held transmitter key until the LED (3.1 /
3.2) is off - depending on the selected channel.
The LED is off - the programming process is completed.
The hand-held transmitter has transmitted the radio code to the radio
receiver.
Teaching in further manual remote controls. Repeat above steps.
Max. 112 memory slots are available per radio receiver.
Deleting manual remote control
button from radio receiver
If a user of a multi-user garage facility moves house and wants to take his
manual remote control with him, then all the codes of the given user's
manual remote control have to be deleted from the radio receiver.
For security reasons, each manual remote control button and/or
combination of buttons should be deleted!
Press setting button (1) and keep depressed for 5 seconds until an
LED starts to flash (any LED).
Release setting button (1) - radio receiver is in delete mode.
Press push-button on the manual remote control, the one whose
code is required to be deleted on the radio receiver - LED goes out -
deletion process complete.
Repeat procedure for all push-buttons and combination of buttons.
5
T2
2
4
6
3.1
3.2
1
7
8
4
5
6
5
2
6
4
3.1
3.2
1
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sommer Duo 650SL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sommer Duo 650SL in de taal/talen: Engels als bijlage per email.

De handleiding is 4,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Sommer Duo 650SL

Sommer Duo 650SL Gebruiksaanwijzing - Nederlands - 40 pagina's

Sommer Duo 650SL Gebruiksaanwijzing - Deutsch - 37 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info