658836
25
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
Starting / Stopping the engine - Starting settings and start-up, - Engine will not start
ENGLISH 25
E
N
G
[Basic settings (chain brake, standard or winter operation, stop switch, primer) as described in
the previous paragraph. ]
Cold start:
Pull the choke lever (7) (this also activates the part-throttle setting) [part throttle control
pin (8) is pulled along].
Using the starter handle, start the engine until you hear it briefly ignite.
Note: the engine cannot start up and continue running while the choke lever is pulled
out.
! After the first audible ignition, immediately:
Press the choke lever back in again.
Continue starting until the engine runs
The engine is then running in part throttle (visible from the part throttle control pin).
Briefly operate the throttle control to cancel the part control setting (the part throttle
control pin jumps back in again).
The engine will then continue to run at idle speed.
Note: If the choke lever is not pushed back in when you hear the first audible ignition, the combustion
chamber can quickly become saturated if start-up is repeated with the choke lever pulled out. In this
case you will be unable to start the device. Please refer to the instructions given in section 5.3,
“Engine will not start”.
Warm start:
Start the engine in idle setting with the choke not pulled out,
or start it in !
part throttle setting:
by pulling the choke out and pressing it back in again [the part throttle setting is
activated as a result, which is visible from the pulled-out part throttle control pin (8)]
Start the engine until it runs, then briefly operate the throttle control to cancel the part
throttle setting (the part throttle control pin jumps back in again).
The engine then runs on at idle speed.
5.3 Engine will not start
If the engine fails to start after several attempts, check whether all adjustments described above have
been correctly carried out, particularly that the stop switch is not in the "0" position. Try starting once
again. The combustion chamber will be flooded, if the engine still fails to start.
In that case we recommend you proceed as follows:
Remove the cowl. (chapter. 3.4)
Pull the spark plug cap off the spark plug.
Remove the spark plug and dry fuel mixture from the electrodes.
Move the throttle lever up to full throttle. Pull the starter handle several times (with removed spark
plug) to clear the combustion chamber.
Move the throttle lever down to idling position, refit the spark plug, the plug cap and the cowl.
Repeat the starting process according to the starting settings for a warm start in part throttle
setting.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Solo-644

Zoeken resetten

  • Hallo!
    Ik heb een Solo 644 kettingzaag. Nu lekt die benzine. Op de aanzuigleiding zit een verdikking die in de opening naar buiten komt. Waarschijnlijk zit die niet meer op de juiste plaats. Hoe kom ik eraan of plaats ik een nieuwe aanzuigleiding? Gesteld op 1-3-2023 om 16:00

    Reageer op deze vraag Misbruik melden
  • Hallo,
    Solo 644 is een hele tijd niet gebruikt
    en start .. heeft wel voldoende compressie
    altijd mengsmering gebruikt,
    mvgr. erlenhofe@hotmail.com
    Gesteld op 23-1-2021 om 10:17

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solo 644 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solo 644 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info