655641
29
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
6 Maintenance, cleaning and storage
ENGLISH 11
6.2 Trial run
At least at the start of every spraying season and in
frequent use at least once a month, perform a trial
run with clean water to check the following:
x Tightness of all equipment components at
maximum permissible pressure with open and
closed shut-off valve
x Function of all active components
(shut-off valve, pump lever)
x Dosing and distribution accuracy of all the
nozzles used by measuring the spraying agent
delivery rate according to section 6.3
Never start working if there are any irregularities or
leaks, if you can see any damage to the equipment
or if the equipment is not working properly in any
way. In this event, immediately have the device
checked by a specialist workshop.
6.3 Checking the spray nozzles and the filter
element
Fill up the tank with clean water to the maximum
marking, start it up and spray for exactly one
minute at an operating pressure of 2 bar [29 psi].
Then measure the quantity of water required to
refill the tank to its maximum level. The value
measured corresponds to the delivery rate of the
device in l/min for the selected operating pressure.
This value must not deviate by more than 10 %
from the value indicated in section 9.
If the actual value is too low, this may be caused
by deposits in the spray nozzle and/or in the filter
element. Clean the parts and repeat the check.
If the actual value is too high, this may be due to
wear or damage to the spray nozzle.
When checking the nozzles, also check whether
the spray nozzle is producing an even, fan-shaped
spray pattern.
If the delivery rate is still too low after cleaning the
nozzle and the filter element, or if the nozzle and/or
the filter element are worn or damaged, replace the
nozzle and/or the filter element by genuine SOLO
replacement parts.
Changing the spray nozzle and the filter element:
See section 6.4
6.4 Changing the spray nozzle and the
filter element
Spray nozzle and filter element must only be
changed if the device is depressurised.
To depressurise the device, hold the spray tube in
the spraying agent tank or in a suitable container
for the spraying agent and operate the shut-off
valve until no more fluid is sprayed.
Changing the spray nozzle or the filter element:
x Rinse the nozzle attachment with clean water.
x Disassemble the nozzle attachment.
x Clean the O-rings, the filter element and the
spray nozzle with clean water and a soft brush.
Never use your mouth to blow through the spray
nozzle! Never use hard objects to clean the
nozzles!
x Replace the previous nozzle by the new nozzle
or the previous filter element by the new filter
element.
x Reassemble the components of the nozzle
attachment (Fig. 22).
6.5 Greasing the cap gasket
If the tank lid becomes hard to tighten or open,
apply silicone grease to the lid gasket.
6.6 Greasing the piston collar and the pump
piston pump
(only 425 Comfort, 435 Comfort,
425 Pro)
After disassembly of the pump components or after
replacing the piston collar, use water resistant
grease to lubricate the piston and the collar.
6.7 Draining the spraying agent tank and
cleaning all other spraying agent carrying
parts
Drain the spraying agent tank, all other spraying
agent carrying parts and the filling strainer daily
after use and particularly at the end of the spraying
season and thoroughly flush them with clean water.
Any unused spraying agent that is left over in the
device could cause corrosion and hence damage
the device. Special attention must be paid to
wearing parts like spray nozzles, filters and seals.
Please read and observe the cleaning instructions
supplied with the spraying agent.
Recommendation: Use the special SOLO cleaner
for plant protection sprayers (dosing bottle of
500 ml [approx. 16.9 oz], part no.: 4900600).
Never use aggressive, acid- or solvent-containing
cleaning agents (gasoline for example).
After cleaning, leave the spraying agent tank open
to dry.
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solo 475 Pro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solo 475 Pro in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info