655625
18
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
1 Safety regulations / 2 Preparing the device for use / 3 Mixing spraying agents and filling the spraying agent tank
ENGLISH 6
x Never smoke in areas where you are
working.
x When removing the spray tube, do not point to
yourself or other persons with the end of the
tube.
1.7 Maintenance, repairs and storage
Only perform maintenance work and repairs by
yourself if they are covered in these operating
instructions. All other work must be carried out by
an authorised workshop.
The repair of modern devices and their safety-
relevant assemblies, requires qualified, specialized
training and a workshop equipped with special
tools and test devices. The specialist has the
required training, experience, and equipment at his
disposal to provide you with the most cost-effective
solution and can help you in many ways with
advice and service.
x The device must not be serviced, repaired
or kept in the vicinity of naked flames.
x Before doing any maintenance work or repairs
and before opening the spraying agent tank,
depressurise the device by pulling on the
pressure relief valve (Fig. 4).
Before pulling on the pressure relief valve (2),
the device must always be in an upright position.
Attention: Keep the device away from your face!
x Always depressurise the device by pulling on the
pressure relief valve (2) before unscrewing the
high-pressure hose, the shut-off valve (5), the
pressure gauge (depending on the model), the
spray tube (1) and the nozzle attachment (4).
x All repairs must only be performed using SOLO
genuine replacement parts.
x The device must not be altered in any way, as
this could adversely affect the safety of the
device and potentially cause an accident or
injury.
2 Preparing the device for use
2.1 Assembly
The pressure sprayer is dismantled before it is
dispatched. It must be fully reassembled again
before it is used.
Installation of the spray tube (1):
x Fasten the threaded collar (Fig. 2, pos. 1) on
straight and firmly screw the spray tube with
O-ring (16x3 mm) hand-tight onto the shut-off
valve. Do not use any tools!
When your work is completed, the spray tube
should be fitted into the holding clamp (10) at the
transport handle (7) (Fig. 3).
Installation of the pressure gauge (depending on
the model):
x Unscrew the black threaded collar from the
shut-off valve.
x Screw the black threaded collar of the pressure
gauge accessory kit onto the shut-off valve.
x Insert the O-ring into the threaded collar and
screw the pressure gauge hand-tight into the
threaded collar. Do not use any tools!
2.2 Spray nozzle and filter element
At the factory, an adjustable spray nozzle is
assembled as the standard spray nozzle.
Delivery rate: See section 4.1
A filter element is fitted in the elbow piece
upstream of the spray nozzle (Fig. 2).
Only the above mentioned standard spray nozzle
(part no.: 49 00 525), the spray nozzles from the
nozzle kit (part no.: 49 00 574) and the genuine
filter element (part no.: 40 74 922 25, mesh
aperture: 0.8 mm [0.031"]) must be used in this
pressure sprayer. Changing spray nozzle and filter
element: See section 5.3
2.3 Height adjustment of the transport handle
In order to allow different sized people back-
friendly working, the height of the transport handle
is adjustable.
Height adjustment of the transport handle (7):
x Unscrew the handle screwing (8) by turning it to
the left (counterclockwise).
x Pull out the transport handle on both sides
evenly until the desired height is set.
x Re-tighten the handle screwing by turning it to
the right (clockwise).
2.4 Trial run
At the first start-up, at the start of the spraying
season and in frequent use at least once a month,
perform a trial run according to section 5.1 to check
the entire device.
3 Mixing spraying agents and
filling the spraying agent tank
When handling the spraying agents, always
follow the safety instructions of these
operating instructions (pay special attention to
section 1.3) and the information provided by the
manufacturer of the particular spraying agent.
Before opening the spraying agent tank,
depressurise the device by pulling on the pressure
relief valve (Fig. 4).
Before pulling on the pressure relief valve (2), the
device must always be in an upright position.
Attention: Keep the device away from your face!
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solo 453 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solo 453 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info