Handleiding Solo 106 (pagina 23 van 100) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans)

634115

Verklein

Vergroot

Pagina terug

1/100

Pagina verder

5. Assembly

1. The equipment will be despatched part-

assembled, and should, therefore, be fully

assembled before taking it into use. Only use

this machine when it is completely assembled.

Ensure that the tank is fully drained before

any assembly, disassembly or modification.

4.8 Maintenance and repair

1.The power tool should be regularly main-

tained. Only execute the maintenance and

repair work yourself that is described in these

operating instructions. All other work should

only be executed by a specialized workshop.

2.For cleaning, maintenance and repair the

motor should always be shut off and the

sparkplug connector should be removed. An

injury hazard through the motor starting

unintentionally. Exception is adjusting the

carburettor and idle.

3.Only original replacement parts from the

manufacturer may be used.

4.No changes may be made to the power tool,

as this could impair the safety of the device

and cause a hazard of accident or injury!

5.The power tool may not be maintained, re-

paired, or stored in the vicinity of open flame.

6.Regularly check the fuel tank cap for leaks.

7.Only use sparkplugs that are problem-free and

that are recommended by the manufacturer.

8.Check the ignition cable for problem-free

condition and intact insulation. If the

sparkplug is unscrewed or the ignition cable is

removed from the socket, then only move the

device if the stop switch is placed on “ 0 /

stop”). A fire hazard exists through sparking!

9.Regularly check the noise suppressor for

problem-free condition. Do not touch the

noise suppressor, as long as is still hot.

5.1 Loop handle (models 105, 106L and 106R)

FIG. 5

1. Turn the loop handle into the correct position.

2. Note: Always install the safety end-stop (1)

on the operator side of the motorised scythe.

If, during use, you carry the motor scythe on

your r.h. side, install the safety end-stop in l.h.

orientation. However, if, during use, you carry

the motor scythe on your l.h. side, install the

safety end-stop in r.h. orientation.

3. Install the safety end-stop (1) on the loop

handle and secure with the spring clip (2).

Never blow in the direction of other people, as

smaller objects can be forced upward at high speeds.

10.Implement the power tool at lowest possi-

ble noise and exhaust levels. Only open the

throttle when working, do not let the motor

run unnecessarily. Please note that noise also

impacts the environment. Observe the quiet

times, that can vary from place to place.

11.Exercise caution when the ground is wet,

with ice and snow, on overhangs, or uneven

terrain. There is an increased risk of slipping!

11.b. Pay particular attention to safety when

working on slopes. Before commencing work,

check the working area for stones, broken

glass, nails, wire or other solid objects and

remove such debris to prevent them being

picked up and thrown out by the cutters.

11.c. Always hold the cutters below hip level. Never lift a

rotating cutter off the ground. Keep all parts of the

body away from rotating cutters.

11.d. Only use cutters in perfect working order

(see chapter 8 ”Using the motor scythe”).

11.e. Never use blunt cutters and avoid uncon-

trolled contact of the cutter with debris. Oth-

erwise there will be an increased risk of kick-

back, which could throw the entire machine

around. Consequently, the operator could be

subjected to involuntary movements, which

could lead to serious injury or death.

11.f. Always stop the engine before any con-

tact with the cutter – even when clearing a

blockage or if cutters have become jammed –

wait until the cutter has stopped and remove

the spark plug cap.

11.g. Stop the engine if you notice a differ-

ence in the operating characteristics of the

motor scythe.

11.h. Due to the centrifugal clutch, the cutters

will run on for a short time, even if you release

the throttle. Ensure the cutter has fully

stopped before storing the machine.

12.Pay attention to obstacles or stumbling

hazards such as tree roots, tree stumps, edges.

13.Do not touch the exhaust and the noise

suppressor, as long as they are still hot, there is

a danger of burn injury!

14.Never work with defective noise suppressor

or without noise suppressor. There is a hazard

of hearing damage and burn injury hazard!

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Solo 106 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info