718606
10
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
speed mode. In ECO mode, the appliance helps to save more energy.
In speed mode, the user can make their coffee faster than in default
setting.
- Below you will see a chart with the active functions of each Mode.
ECO Mode Speed Mode Default Setting
Illumination
Light
No Yes Yes
Pre-brewing* Yes No Yes
Auto shut off
time
10mins 30mins 20mins
Cup Volume
memory
Yes Yes Yes
*Note: The pre-brewing function moistens the grounded beans in
the brewer with a small amount of water before full extraction. This
expands the coffee grounds to build up a greater pressure in the
brewer which help extraction of all the oils and full avor from the
grounded beans.
TO SELECT THE DESIRED MODE:
- When the machine is in standby condition, press and holds the ON/
OFF Button (G) for 5 seconds, so it (G) will begin to ash. Then release
and pass to the next point
- The Icon ON/OFF (G) will then be ashing and the following button will
have the following indications
- To know which mode it is in, the table below indicates what is shown in
the different settings:
Hot water
button (I)
Strong coffee
button (J)
Mild coffee
button (K)
In ECO Mode Lights ON Flashing Flashing
In Speed
Mode
Flashing Lights ON Flashing
In Default
Setting
Flashing Flashing Lights On
- To change the MODE, press the hot water button (I) for ECO mode,
strong espresso button (J) for speed mode and mild espresso button
(L) for default setting.Two Beep sound will be heard indicates that the
mode is being selected. (Note: If you are pressing the relative lights on
button for each mode, the machine will not response).
- If you would like to remain the setting unchanged, press ON/OFF
button (G again or wait for 5 seconds for the machine to return to the
standby condition.
CLEANING & MAINTENANCE
SELF-CLEANING
- When icon (E) is ashing, it indicates that the appliance needs to
undergo self-cleaning. The appliance will remain in the best condition
if this function is performed at least once a month or more regularly
depending on the hardness of water used. It is also suggested:
- Fully ll the water tank (14).
- Adding one pack of cleaning agent included in the box to the water
tank.
IMPORTANT: Do not use vinegar or other cleaning agent to do self-
cleaning of this appliance. The cleaning agent might damage the
appliance.
- Plug in the appliance.
- Place a sufcient large container under the coffee spout.
- In standby condition, press and hold ON/OFF Button (G) and strong
coffee button (J) at same time, for 5 seconds. A beep sound will be
heard with Icon (E) and strong coffee button (J) will be ashing.
- Press strong coffee button (J) to conrm undergoing the self-cleaning
process. To resume back to the standby condition, press ON/OFF
button (G).
- Icon (E) will be ashing indicates that the appliance is undergoing the
self-cleaning process. (Caution: Keep skin/body away from the hot
water.)
- When all the water in the water tank is being dispensed out, Icon (A)
(Low water level) and strong coffee button (J) will be ashing. Remove
all the remaining solution in the water tank (14) and ll the tank with
normal tap water until the MAX position. When water is lled into the
water tank, Icon (A) will goes off. Then the appliance will continue the
descaling process, the appliance will brew half of water tank rst and
then waiting for around 1min, after that will brew the outstanding water
from the water tank.
- When the self-cleaning process is completed, the appliance will switch
off automatically.
Note: To ensure the descaling process can be completed, please be
patient during the process and make sure the applicant switch off
automatically.
EMPTY SYSTEM FUNCTION
- The empty system function is recommended to be used before long
period of non-use, frost protection and before talking to repair agent.
- In standby condition, press and hold the ON/OFF button (G) and mild
coffee button (K) together for 5 seconds.
- Empty System Icon (F) will then be ashing.
- Remove the water tank from the appliance. Icon (F) will light up stably
indicates that the empty system is under process. You can press ON/
OFF Button (G) before removing the water tank (14) to resume back to
the standby condition.
- When the empty system function is completed, the appliance will switch
off automatically.
Important: After perform EMPTY SYSYEM FUNCTION; when you use
the coffee machine again, press the hot water button (I) until water
can come out from spout (5) when the coffee maker is reused again.
MANUAL RINSING
- You can perform a manual rinsing cycle to clean the coffee nozzle after
use. It is also suggested to perform a manual rinsing if the appliance
has not been used for a long period of time.
- In standby condition, press and hold the ON/OFF Button (G) and hot
water button (I) together.
- The hot water button(I), strong coffee button (J) and mild coffee button
(K)will then goes off. The coffee nozzle (9) will then dispense a small
amount of water which is used for the rinsing.
Danger: Water comes out of the coffee nozzle is hot and is collected
in the drip tray underneath. Avoid contact with splashes of water.
- After rinsing, the appliance will return to the standby condition.
CLEANING THE APPLIANCE
- Disconnect the power cord (15) from the main power outlet.
- Empty all the water in the internal (3) and external drip tray (1)
- Use a damped cloth or non-scratching cleaner to clean the water stains
on the appliance.
IMPORTANT: Never use any abrasive, vinegar or descaling agents
not included in the box to clean the appliance.
CLEANING COFFEE POWDER OUTLET
- Coffee grounds may stick on the wall of ground outlet of appliance,
on the way to Brewing unit (17), after an extended period of use. It is
suggested to clean the outlet by following steps to ensure that coffee
grounds can make it to the brewer.
- Push the service door recess area (Fig 2)
- Take out the service door (Fig 3)
- Press the release knob of brewer (Fig 4)
- Take the brewing unit out (Fig 5)
- Use Cleanness Brush (18) to clean the powder outlet (Fig 12)
TROUBLESHOOTING
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Solac CA4810 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Solac CA4810 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 3,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info