110660

Smeg SC45V2 Handleiding

35
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
Instructions for Use
Steam oven
Bedienungsanleitung
Dampfgarer
Table of Contents
EN
INSTRUCTIONS FOR THE USER
: these provide recommendations for
use, a description of the controls and the correct procedures for cleaning
and maintaining the appliance
INSTRUCTIONS FOR THE INSTALLER
: these are intended for the
qualified engineer who is to install, commission and test the appliance
1
PRECAUTIONS FOR USE ................................................................................ 1
2
DISPOSAL INSTRUCTIONS - OUR ENVIRONMENT POLICY ........................ 2
3
SAFETY PRECAUTIONS .................................................................................. 3
4
GET TO KNOW YOUR OVEN ........................................................................... 6
5
ACCESSORIES AVAILABLE ............................................................................ 6
6
BEFORE INSTALLATION ................................................................................. 7
7
DESCRIPTION OF FRONT PANEL CONTROLS ............................................. 8
8
USING THE OVEN .......................................................................................... 10
9
WATER FEEDING ........................................................................................... 11
10
SELECTING THE FUNCTION ......................................................................... 12
11
RECOMMENDED COOKING TABLES ........................................................... 21
12
CARE AND MAINTENANCE ........................................................................... 26
13
OVEN CLEANING ........................................................................................... 29
14
EXTRAORDINARY MAINTENANCE ............................................................... 30
15
INSTALLING THE APPLIANCE ...................................................................... 31
Precautions for Use
EN
1
1 PRECAUTIONS FOR USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD
CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE CYCLE.
WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT
CONTAINS CAREFULLY BEFORE USING THE APPLIANCE. INSTALLATION
MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE
RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD
USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE.
THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION:
COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE
CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN
THOSE STATED ABOVE.
KEEP THE DOCUMENTATION OF THIS PRODUCT FOR FUTURE REFERENCE.
ALWAYS KEEP THE INSTRUCTION MANUAL HANDY. IF YOU LEND THE
STEAMER TO SOMEONE ELSE GIVE THEM THE MANUAL AS WELL!
NEVER USE THIS APPLIANCE FOR HEATING ROOMS.
NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME.
SEPARATE THE VARIOUS PACKAGING MATERIALS BY TYPE AND CONSIGN
THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE.
THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).
THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE
COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES
THROUGHOUT THE EUROPEAN UNION.
NEVER OBSTRUCT THE OPENINGS AND SLITS PROVIDED FOR
VENTILATION AND HEAT DISPERSAL.
THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK
IS IN A VISIBLE POSITION ON THE OVEN DOOR FRAME.
THE NAMEPLATE MUST NEVER BE REMOVED.
NEVER USE METAL SCOURING PADS OR SHARP SCRAPERS
WHICH WILL DAMAGE THE SURFACE.
USE ORDINARY NON-ABRASIVE PRODUCTS WITH THE AID OF
WOODEN OR PLASTIC UTENSILS IF NECESSARY. RINSE
THOROUGHLY AND DRY WITH A SOFT CLOTH OR CHAMOIS
LEATHER.
Disposal Instructions
EN
2
2 DISPOSAL INSTRUCTIONS -
OUR ENVIRONMENT POLICY
Our products are only packaged using non-pollutant, environment-friendly,
recyclable materials. We urge you to cooperate by disposing of the
packaging properly. Contact your local dealer or the competent local
organisations for the addresses of collection, recycling and disposal
facilities.
Never leave all or part of the packaging lying around. Packaging parts,
and especially plastic bags, may represent a suffocation hazard for
children.
Your old appliance must also be disposed of properly.
Important: deliver the appliance to your local organisation authorised to
collect scrapped appliances. Proper disposal allows the intelligent
recovery of valuable materials.
Before scrapping your appliance it is important to remove doors and leave
shelves in position as for use, to ensure that children cannot accidentally
become trapped inside the oven during play. Also, cut the power supply
lead and remove it and the plug.
EN
Safety Precautions
3
3 SAFETY PRECAUTIONS
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY
REGULATIONS FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION
FUNCTIONS.
IN YOUR INTEREST AND TO ENSURE YOUR SAFETY, BY LAW ALL ELECTRIC
APPLIANCES MUST ONLY BE INSTALLED AND SERVICED BY QUALIFIED
STAFF, IN ACCORDANCE WITH THE RELEVANT REGULATIONS.
OUR APPROVED INSTALLATION ENGINEERS GUARANTEE YOU A JOB WELL
DONE.
GAS OR ELECTRIC APPLIANCES MUST ALWAYS BE DISCONNECTED BY
SUITABLY SKILLED PEOPLE.
THE PLUG TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE
RELATIVE SOCKET MUST BE OF THE SAME TYPE AND COMPLY WITH THE
RELEVANT REGULATIONS.
THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE
APPLIANCE HAS BEEN BUILT-IN.
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD
THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH
ELECTRICAL SYSTEM SAFETY REGULATIONS.
IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE
OVEN FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL.
IF THE APPLIANCE FAILS TO OPERATE, DISCONNECT IT FROM THE
ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.
WARNING! NEVER LEAVE THE OVEN UNSUPERVISED.
WARNING! IF YOU SEE SMOKE OR FIRE, KEEP THE DOOR CLOSED IN
ORDER TO SMOTHER THE FLAMES. SWITCH OFF THE OVEN AND TAKE THE
PLUG OUT OF THE SOCKET OR CUT OFF THE OVEN POWER SUPPLY.
WARNING! OVERHEATED FAT AND OIL CAN EASILY CATCH FIRE. HEATING
OIL IN THE COOKING SPACE TO SEAR MEAT IS DANGEROUS AND SHOULD
NOT BE DONE. NEVER TRY TO EXTINGUISH BURNING OIL OR FAT WITH
WATER (DANGER OF EXPLOSION)! SMOTHER THE FLAMES WITH A DAMP
CLOTH AND KEEP ALL DOORS AND WINDOWS CLOSED.
WARNING! DO NOT USE ALCOHOL TO COOK IN THE OVEN. IT CAN CAUSE
THE OVERHEATING OF THE FOOD. DANGER OF EXPLOSION!
WARNING! THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS
(INCLUDING CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL
CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY
HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF
THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY
WITH THE APPLIANCE.
EN
Safety Precautions
4
WARNING: ACCESSIBLE PARTS MAY BECOME HOT DURING USE. YOUNG
CHILDREN SHOULD BE KEPT AWAY.
WARNING: DURING USE THE APPLIANCE BECOMES VERY HOT. CARE
SHOULD BE TAKEN TO AVOID TOUCHING HEATING ELEMENTS INSIDE THE
OVEN. RISK OF BURNS!
WARNING! WHEN OPENING THE DOOR DURING OR UPON COMPLETION OF
THE COOKING CYCLE, BE CAREFUL OF THE FLOW OF HOT AIR AND/OR
STEAM AND WATER DROPS COMING OUT OF THE COOKING CHAMBER.
STEP BACK OR TO THE SIDE TO AVOID BURNS.
WARNING! MAKE SURE YOU NEVER CATCH THE POWER CABLES OF
OTHER ELECTRICAL APPLIANCES IN THE HOT DOOR OR THE OVEN. THE
CABLE INSULATION MAY MELT. DANGER OF SHORT-CIRCUITING!
THIS OVEN IS EXCLUSIVELY FOR DOMESTIC USE!
THE APPLIANCE IS DESIGNED FOR USE IN THE HOME FOR PREPARING
FOOD. NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY
IMPROPER OR INCORRECT USE.
AVOID DAMAGING THE OVEN OR OTHER DANGEROUS SITUATIONS BY
FOLLOWING THESE INSTRUCTIONS:
Do not cover or obstruct the ventilation openings.
Do not keep any inflammable object inside the oven as it may
burn if the oven is switched on.
Do not use the oven as a pantry.
Do not pour spirits (e.g. brandy, whisky, schnapps, etc.) over
hot food. DANGER OF EXPLOSION!
Accessories such as wire racks and trays, etc. get hot in the
cooking space. Always wear protective gloves or use oven
cloths.
To avoid being burnt, always use oven gloves for handling
dishes and containers and touching the oven.
Do not lean or sit on the open oven door. This may damage
the oven, especially in the hinge zone. The door can bear a
maximum weight of 8 kg.
The racks can bear a maximum load of 8 kg. To avoid
damaging the oven, do not exceed this load.
EN
Safety Precautions
5
CLEANING:
The appliance will remain hot for some time after it is switched
off and cool down only slowly to room temperature. Please
allow sufficient time for the appliance to cool down before, for
instance, cleaning it.
DO NOT USE HARSH ABRASIVE CLEANERS OR SHARP
METAL SCRAPERS TO CLEAN THE OVEN DOOR GLASS
SINCE THEY CAN SCRATCH THE SURFACE, WHICH MAY
RESULT IN SHATTERING OF THE GLASS.
The door contact surfaces (the front of the cooking space and
the inside part of the doors) must be kept very clean in order to
ensure the oven functions correctly.
Please follow the instructions regarding cleaning in the section
“Oven Cleaning and Maintenance”.
REPAIRS:
If the power cable is damaged it should be substituted by the
manufacturer, authorised agents or technicians qualified for this
task in order to avoid dangerous situations. Furthermore,
special tools are required for this task.
Repair and maintenance work, especially of current carrying
parts, can only be carried out by technicians authorised by the
manufacturer.
The manufacturer declines all responsibility for injury or damage caused by failure
to comply with the above regulations or deriving from tampering with even just one
part of the appliance and the use of non-original spare parts.
EN
Instructions for the User
6
4 GET TO KNOW YOUR OVEN
– Door window glass
– Non-perforated container
– Catches
– Rack
– Lamp
– Shelf guides
– Control panel
– Sponge
– Perforated container
5 ACCESSORIES AVAILABLE
Perforated container: suitable for cooking
fresh or deep frozen vegetables, meat and
poultry.
Non-perforated container: suitable for
steaming sensitive foods, e.g. compotes and
dumplings. You can use it with the perforated
container to catch the water.
Rack: used when cooking with small
containers, as for example, dessert bowls and
to regenerate plate dishes.
Oven accessories which may come into contact with foods are made from
materials compliant with the EC Regulation 1935-2004 and national
relevant regulations.
EN
Instructions for the User
7
6 BEFORE INSTALLATION
Never leave packaging residues unattended in the home. Separate waste
packaging materials by type and consign them to the nearest separate
disposal centre.
The inside of the appliance should be cleaned to remove all manufacturing
residues. For further information about cleaning, see point "CARE AND
MAINTENANCE".
EN
Instructions for the User
8
7 DESCRIPTION OF FRONT PANEL CONTROLS
All the appliance's control and monitoring devices are placed together on
the front panel. The table below provides the key to the symbols used.
Function’s
parameters
knob
This knob allows you to set
the time, select the cooking
temperature and duration
and program the cooking
start and end times. From
now on, for convenience it
will be referred to as PT1.
F
unction
-
switch on
knob
This knob allows access to
the oven's three operating
settings, and is also used to
select a cooking function
(see point “8.2 Operating
settings”).
Current
time /
Duration
display
This display shows the
current time or the cooking
duration.
Also visible are the function
cut-out light
Clock
Adjusting the cooking time
Child lock out
function
Child lock-out function mode
on (see point “10.3.4 Child
safety lock-out function”)
Cooking duration
Setting the cooking duration
Delayed start
Setting the cooking time with
a delayed start
EN
Instructions for the User
9
Temperat
ure / Type
of food
display
This display shows the
Parameters set for the
function required, or the
Parameters set by the user.
Temperature
The oven is heating up
Descale function
See point 10.3.2 Descale
function
Water level
indication
Indicates the existing water
quantity in the tank (see
point 9.2 Water levels
indication)
F
unction
display
This display shows
(illuminated) all the cooking
functions available for
selection. For instructions on
how to select a cooking
function, see point “10
Selecting a cooking
function”.
The table below provides a list of the functions available.
Please see chapter 10 for a more detailed description of the functions
STEAM – MANUAL
VEGETABLES COOKING
MEAT COOKING
REHEATING & STERILISING
FISH COOKING
DEFROSTING
EN
Instructions for the User
10
8 USING THE OVEN
8.1 Precautions and General Advice
When the oven is used for the first time, it should be heated to the
maximum temperature for long enough to burn off any oily residues left by
the manufacturing process, which might contaminate foods with
unpleasant smells.
The accessories can contain hot water when they are taken from the oven,
therefore the use of gloves and particular attention are always
recommended
Oven accessories which may come into contact with foods are made from
materials compliant with the EC Regulation 1935-2004 and national
relevant regulations.
8.2 Operating settings
This product is programmed to provide 3 operating settings, which can
be\modified by pressing PT2.
Standby setting: activated as soon as the current time has been
confirmed, with DSP1 on and showing the current time.
ON setting: from the standby setting, press PT2 once. All the displays and
knobs light up.
OFF setting: from the ON setting, press PT2 once.
Only the symbol on DSP1 remains on.
The heating system is not activated immediately in any of these
functions, in order to improve operator safety.
8.3 First Use
At first use, or after a power failure, the oven's left hand-display, DSP1, will
show a flashing symbol. The oven will not operate until the clock,
the water hardness parameter and the calibration is set.
8.3.1 Setting the current time and the water hardness level
To set the current time, turn PT1 to the right and left to increase or
decrease the hours.
Press PT1 once to move on to setting the minutes. Turn it to the right and
left to increase or decrease the minutes.
Press PT1 again to confirm the current time and move on to water
hardness level setting. The DSP2 will show the word “Dur” and DSP1 will
show the water hardness level “MEd” (pre-set value).
Turn PT1 to the right and left to change the water hardness level value, as
described in table below
EN
Instructions for the User
11
Press PT1 to confirm the water hardness level.
TYPE
WATER HARDNESS
disp 1
Ca + Mg
(ppm)
English deg.
[°eH]
French deg.
[°dF]
German deg.
[°dH]
SOFT WATER 0 TO 150 0 TO 11 0 TO 15 0 TO 8
SOFT
MEDIUM WATER 151 TO 350
12 TO 25 16 TO 35 9 TO 20
MED
HARD WATER 301 TO 500
26 TO 35 36 TO 50 21 TO 28
HARD
8.3.2 Water Level calibration
After setting the water hardness, appears in the Display and the
water level lights shine.
Please take the Water tank completely off. Wait until the display and the
water tank lights disappear.
8.3.3 Changing the current time
It might become necessary to change the current time, for example at the
switch from summer to winter time. To do this, starting from the standby
setting (see point “8.2 Operating settings”) keep PT1 pressed for a few
seconds until the figures on DSP1 flash. Now repeat the operations
described in point “8.3.1 Setting the current time and water hardness
level”.
8.3.4 Changing the current water hardness level
It might become necessary to change the current water hardness level. To
do this, please refer to point “10.3.3 changing the water hardness level”.
9 WATER FEEDING
All functions require the water tank to be full.
Fill the water tank up to the “MAX” mark, which is in the water tank, with
cold, fresh drinking water and introduce it into the slot located above the
cavity (recommended 1,2 L, maximum 1,4 L).
If the indication “rES” appears, it means that the water tank was not
properly inserted.
9.1 Refilling the water
The contents of the water tank
normally suffice for one cooking
session of 50-60 minutes.
If, however, the water tank needs to
be refilled, the water refill light starts
to flash . Only fill the water
tank up to a maximum of 0.5 litres
to ensure that the water does not overflow when it is pumped back to
the water tank. RISK OF OVERFLOW.
EN
Instructions for the User
12
9.2 Water levels indication
The steamer indicates the existing water quantity in the tank through 3
levels, which correspond to the following percentages:
- – 0% to 20%
- – 20% to 60%
- – 60% to 100%
Remark: don’t refill the tank, if it’s placed. Please remove it completely and
wait > 20 sec. before placing it again.
9.3 Emptying the water tank
When the appliance is switched off, the residual water is pumped back into
the water tank.
While the water is being pumped the display shows “PUMP”.
This message stays on until the temperature of the water reaches 75º C
before it can be pumped back to the water tank.
If the display shows “FULL” it means that the water has too much water
inside. Please empty the tank and place it again.
Warning: the water in the tank may be hot. Danger of burns!
After the water is pumped back to the water tank, the display will show the
message “DEP” requiring the following actions:
1. Remove and empty the water tank.
2. Dry the water tank and introduce it back into the slot located above
the cavity. Clean and dry the cooking space.
3. Leave the appliance door open so that the cooking space can cool
down and dry completely.
IMPORTANT NOTE: It is advisable to remove the water tank and
empty it after a cooking cycle. This prevents the formation of bacteria
and limestone inside the appliance.
Don’t wash the water tank in the dishwasher machine.
If the water tank has not been removed from the oven and a new cooking
cycle is started, the oven displays the warning “DEP”.
This warning can be cleared by pressing PT2 and proceed with the new
cooking cycle without removing and emptying the water tank.
10 SELECTING THE FUNCTION
In the ON state only, a cooking function can be selected by simply turning
PT2 to the right or left. The function selected will change colour to orange
on DSP3. The preset cooking time will be displayed on DSP1 and the
preset parameters (temperature, food type) are displayed on DSP2.
The suggested times and temperatures are guideline values. The actual
cooking time can vary according to the type and quality of the foods.
EN
Instructions for the User
13
10.1.1 Steam function (Manual program)
After selecting this function, press PT1 to modify the preset parameters of
cooking time and temperature. The temperature light starts to blink.
Turn PT1 to the right or left to change the preset temperature.
Press PT1 to validate and the cooking duration light starts to blink.
Turn PT1 to the right or left to change the preset cooking duration.
Please consider the information on the cooking table (see point 10).
Press PT2 to immediately start the cooking process or otherwise press
PT1 to set a different time for the cooking process start (please refer to
point “10.1.7 Delayed Start Time”).
10.1.2 Meat Cooking function (Automatic program)
After selecting this function, press PT1 to modify the preset parameters
and the DSP2 starts to blink.
Turn PT1 to the right or left to change the preset food type displayed on
DSP2.
The cooking duration is calculated based on the food’s type but can be
changed by pressing PT1.
Turn PT1 to the right or left to change the preset cooking duration.
Press PT2 to immediately start the cooking process or otherwise press
PT1 to set a different time for the cooking process start (please refer to
point “10.1.7 Delayed Start Time”).
The temperature will be automatically set to achieve the best results.
The following table shows the programmes, indicating the time that the
function will take.
PROGRAM TYPE OF MEAT TEMPERATURE ºC
TIME
(MIN)
CONTAINER LEVEL
C 1
CHICKEN
BREAST
100 ºC 30 PERFORATED 2
C 2
SMOKED PORK
LOIN / PIECES
100 ºC 45 PERFORATED 2
C 3
TURKEY
ESCALOPE
100 ºC 20 PERFORATED 2
C 4 PORK FILET,
WHOLE
100 ºC 25 PERFORATED 2
C 5
VIENNA
SAUSAGES
90 ºC 15 PERFORATED 2
10.1.3 Fish Cooking function (Automatic program)
After selecting this function, press PT1 to modify the preset parameters
and the DSP2 starts to blink.
Turn PT1 to the right or left to change the preset food type displayed on
DSP2.
The cooking duration is calculated based on the food’s type but can be
changed by pressing PT1.
Turn PT1 to the right or left to change the preset cooking duration.
EN
Instructions for the User
14
Press PT2 to immediately start the cooking process or otherwise press
PT1 to set a different time for the cooking process start (please refer to
point “7.4.7 Delayed Start Time”).
The temperature will be automatically set to achieve the best results.
The following table shows the programmes, indicating the time that the
function will take.
PROGRAM
TYPE OF
FISH
TEMPERATURE
ºC
TIME
(MIN)
CONTAINER LEVEL
b 1 TROUT 80°C 25 PERFORATED
2
b 2
SHRIMP 90°C 15 PERFORATED
2
b 3
FISH FILET 80°C 18 PERFORATED
2
b 4
MUSSELS 100°C 25 PERFORATED
2
b 5
LOBSTER 100°C 30 PERFORATED
1/2
10.1.4 Vegetables Cooking function (Automatic program)
After selecting this function, press PT1 to modify the preset parameters
and the DSP2 starts to blink.
Turn PT1 to the right or left to change the preset food type displayed on
DSP2.
The cooking duration is calculated based on the food’s type but can be
changed by pressing PT1.
Turn PT1 to the right or left to change the preset cooking duration.
Press PT2 to immediately start the cooking process or otherwise press
PT1 to set a different time for the cooking process start (please refer to
point “10.4.7 Delayed Start Time”).
The temperature will be automatically set to achieve the best results.
The following table shows the programmes, indicating the time that the
function will take.
PROGRAM FOOD
TEMPERATURE
(°C)
TIME
(MIN)
CONTAINER LEVEL
A 1
BROCCOLI
100°C
20 PERFORATED 2
A 2
CARROTS
100°C
25 PERFORATED 2
A 3
POTATOES
AND MIXED
VEGETABLES
100°C
25 PERFORATED 2
A 4
SNOW PEAS
100°C
15 PERFORATED 2
A 5 ASPARAGUS
100°C
25 PERFORATED 2
10.1.5 Re-Heating and Sterilising function (Automatic program)
After selecting this function, press PT1 to modify the preset parameters
and the DSP2 starts to blink.
Turn PT1 to the right or left to change the preset food type displayed on
DSP2.
EN
Instructions for the User
15
The cooking duration is calculated based on the food’s type but can be
changed by pressing PT1.
Turn PT1 to the right or left to change the preset cooking duration.
Press PT2 to immediately start the defrost process or otherwise press PT1
to set a different time for the defrost process start (please refer to point
“10.1.7 Delayed Start Time”).
The temperature will be automatically set to achieve the best results.
The following table shows the programmes, indicating the time that the
function will take.
PROGRAM
TYPE OF
FOOD
TEMPERATURE
ºC
TIME
(MIN)
INSTRUCTIONS CONTAINER
LEVEL
r 1 PLATE DISHES
100°C 13
RACK 2
r 2
READY-MADE
MEALS /
FROZEN
100°C 18
REMOVE LID
FROM
CONTAINER
AND PUT ON
RACK.
RACK 2
r 3
BEANS 100°C 35
STERILISING:
THE TIMES AND
TEMPERATURE
S REFER TO 1L
PRESERVING
JARS.
RACK 2
r 4
CHERRIES 80°C 35
RACK 2
r 5
PLUMS 90°C 35
RACK 2
r 6
BABY
BOTTLES
100ºC 12
RACK 2
10.1.6 Defrost function (Manual program)
After selecting this function, press PT1 to modify the preset cooking
duration and the DSP1 starts to blink.
Turn PT1 to the right or left to change the preset defrosting duration.
Please consider the information on the defrosting table (see point 10).
Press PT2 to immediately start the defrost process or otherwise press PT1
to set a different time for the defrost process start (please refer to point
“10.1.7 Delayed Start Time”).
10.1.7 Delayed Start Time
When PT1 is pressed to define a delayed start time the corresponding
light starts to blink, DSP1 shows the current time and DSP 2 shows
“Auto”.
Turn PT1 to the right or left to change the delayed start time.
Press PT2 to validate the delayed start time.
The oven enters in an idle state waiting for the defined start time. DSP3
shows the selected function and DSP1 and DSP2 show all the defined
parameters for the function continuously alternating.
If you wish to start the function before the selected time, just press PT2.
If you wish to cancel the programming, press PT2 for 3 seconds.
10.2 When the oven is working…
IT IS NORMAL THAT SOME STEAM ESCAPES THROUGH THE
OPENING BETWEEN THE DOOR AND CONTROL PANEL DURING THE
EN
Instructions for the User
16
HEATING PERIOD. THE AMOUNT OF RELEASED STEAM WILL BE
REDUCED WHEN THE OVEN REACHES THE SET TEMPERATURE.
10.2.1 Interrupting a cooking cycle
You can stop the cooking process at any time by pressing the PT2 key
once or by opening the oven door.
The oven incorporates a steam-reduction function that is activated when
the Start/Stop key is pressed to gradually release the steam from the
cavity, so that there is no sudden rush of steam when the appliance door
is opened.
This function takes around 3 minutes and during it the display shows the
word “VAP”.
WARNING! WHEN OPENING THE DOOR DURING OR COMPLETION
OF THE COOKING CYCLE WITHOUT STOPPING IT AS DESCRIBED
ABOVE BE CAREFUL OF THE FLOW OF HOT AIR AND/OR STEAM
COMING OUT OF THE COOKING CHAMBER. STEP BACK OR TO THE
SIDE TO AVOID BURNS.
At this point:
Steam generation is stopped immediately although steam
continues to be produced until the water cools down in the
boiler.
The cavity walls and the water tank are still very hot. Danger of
burning!
The timer stops and the display shows the remaining amount of
operating time.
If you wish, at this time you can:
Turn or stir the food to ensure it will be evenly cooked.
Modify the process parameters.
Cancel a cooking cycle
End of a cooking cycle.
To restart the process, close the door and press PT2.
10.2.2 Modifying parameters
The operating parameters (time, temperature, etc.) can only be modified
when the cooking process has been interrupted. Proceed as follows:
Press PT1 to activate the parameter modification mode. The
symbol starts to blink. Turn PT1 to the right or left to
change the remaining cooking duration.
Press PT1 to validate and the next parameter light starts to
blink. Proceed as described in the active function chapter to
modify the remaining parameters.
Press PT2 to continue the cooking process.
10.2.3 Cancelling a cooking cycle
If you wish to cancel the cooking process, press PT2 for 3 seconds.
You will then hear a beep and the oven will be in the condition described
in the following paragraph (10.2.4)
EN
Instructions for the User
17
10.2.4 End of a cooking cycle
At the end of the set duration or when you press PT2 to finish the cooking
cycle, you will hear three beeps and the display will show the word “End”
flashing, the oven starts the steam-reduction function.
This function gradually releases the steam from the cavity, so that there is
no sudden rush of steam when the appliance door is opened.
This function takes around 3 minutes and during it the display shows the
word “VAP”. If you want to start a new cooking cycle press PT2 and rotate.
WARNING! WHEN OPENING THE DOOR DURING OR COMPLETION
OF THE COOKING CYCLE WITHOUT STOPPING IT AS DESCRIBED,
BE CAREFUL OF THE FLOW OF HOT AIR AND/OR STEAM COMING
OUT OF THE COOKING CHAMBER. STEP BACK OR TO THE SIDE TO
AVOID BURNS.
The cooling fan can continue to run for a certain length of time after
the appliance has been switched off. This is a normal function that is
meant to reduce the temperature inside the oven.
In the meantime, as soon as the water in the boiler reaches below 75 ºC it
is pumped back to the water tank. This phase can take as long as 10
minutes and the DSP1 shows the message “PUMP”. If the display shows
“FULL” it means that the water has to match water inside. Please empty
the tank and place it again.
When the display shows the word “DEP”, this means that the water was
pumped and that the water tank can be removed.
Remove the water tank and dry it thoroughly. Let the cooking space cool
down for a moment and then clean and dry it with a cloth or sponge. The
door should be left open for some time so that the appliance can dry
completely.
10.3 Secondary menu
This appliance also has a concealed "secondary menu" allowing the user
to:
1. Activate or deactivate the Show Room function (which disables all the
heating elements so that only the control panel works);
2. Perform a Descale cycle;
3. Change the Water Hardness Level
4. Activate or deactivate the child safety device ( );
10.3.1 Show Room Function
With the oven in OFF status (see point “8.2 Operating settings”) keep PT1
pressed until the message OFF SHO appears on DSP1 and DSP2. This
means that the SHOW ROOM function (which disables all the heating
elements so that only the control panel works) is not active.
Turn PT1 to the right or left to activate (ON SHO) or deactivate (OFF SHO)
this function. To use the oven normally, set OFF SHO.
After setting the parameter required, press PT2 to return the oven to the
initial standby status.
EN
Instructions for the User
18
10.3.2 Descale function
Warning: For safety reasons, the descaling process cannot be
interrupted and it takes about 45 minutes.
The appliance can be descaled with the appliance door open or closed.
(See 11.1)
To run a descaling cycle proceed as follows:
With the oven in OFF status (see point “8.2 Operating settings”) keep PT1
pressed until the message OFF SHO appears on DSP1. Now press PT1
until the message “ENTR CAL” appears on DPS1 and DSP2.
Turn PT1 to the right press PT2 at the same time to activate the descale
program . When this function is active, the symbol appears on DPS2.
When the display shows “0.5L”, remove the water tank.
Pour 0,5 litres of an adequate descaling solution into the water tank and
put the water tank back (see 11.2).
Press PT2 to start the Descale cycle that takes about 30 minutes.
When the display shows “1.0L” flashing and the oven emits a beep,
remove and empty the water tank.
Fill the water tank with 1,0 litres of cold water and put the water tank back.
Press PT2 to start the first rinsing cycle.
When the display again shows “1.0L” flashing and the oven emits a new
beep, remove and empty the water tank.
Fill the water tank with 1,0 litres of cold water and put the water tank back.
Press PT2 to start the second rinsing cycle.
When the rinsing cycle has finished the display shows “End”.
Remove, empty and dry the water tank.
10.3.3 Changing the water hardness level
With the oven in OFF status (see point “8.2 Operating settings”) keep PT1
pressed until the message OFF SHO appears on DSP1. Now press PT1
until the message “MED DUR” appears on DPS1 and DSP2.
Turn PT1 to the right or left to change the hardness level. Available
options are HARD, MED and SOFT.
After setting the parameter required, press PT2 to return the oven to the
initial standby status.
EN
Instructions for the User
19
10.3.4 Child safety lock-out function
With the oven in OFF status (see point “8.2 Operating settings”) keep PT1
pressed until the message OFF SHO appears on DSP1. Now press PT1
until the message “OFF BLOC” appears on DPS1.
Turn PT1 to the right or left to activate (ON BLOC) or deactivate (OFF
BLOC) this function, which locks out all the functions and knobs after 3
minutes of operation without any command from the user (when this
system is active, the symbol appears on DPS2).
After setting the parameter required, press PT2 to return the oven to the
initial standby status.
To exit the lockout status temporarily to modify a cooking program or
select a different function, keep PT1 pressed until the symbol
disappears from DSP2. The required changes can now be made, and 2
minutes after the last setting is made the lockout will come into operation
again.
To deactivate the lockout permanently, access the secondary menu and
switch the function off as described in this section.
EN
Instructions for the User
20
10.4 Display messages
DISPLAY DESCRIPTION
DESCALING
SOFT
SOFTSOFT
SOFT
SOFT WATER.
med
medmed
med
MEDIUM WATER.
hard
hardhard
hard
HARD WATER.
CAL
CALCAL
CAL
APPLIANCE MUST BE DESCALED.
FLASHING – DESCALING STARTS.
0.5L
0.5L0.5L
0.5L
FEED 0.5 LITRE DESCALING SOLUTION INTO THE WATER TANK.
1.0L
1.0L1.0L
1.0L
FEED 1 LITRE COLD WATER INTO THE WATER TANK FOR RINSING.
WATER TANK
INDICATION THAT WATER TANK IS MISSING OR WRONGLY INSERTED
THE WATER TANK MUST BE REMOVED, EMPTIED AND REINSERTED.
STEAM REDUCTION AND WATER PUMPING
VAP
VAPVAP
VAP
INDICATION THAT STEAM REDUCTION PROCESS IS ONGOING.
PUMP
PUMPPUMP
PUMP
INDICATION THAT COLD WATER IS ENTERING THE BOILER AND HOT
WATER IS BEING PUMPED TO THE WATER TANK.
FULL
FULLFULL
FULL
THE WATER TANK MUST BE REMOVED, EMPTIED AND REINSERTED.
PERFORM WATER LEVEL CALIBRATION ( SEE 8.3.2)
SYSTEM WARNINGS
TEMPERATURE IN THE PCB IS TOO HIGH.
SYMBOLS
CHILD SAFETY LOCK-OUT FUNCTION
DESCALE FUNCTION
WATER LEVEL INDICATION
TEMPERATURE
10.5 Cooling fan system
The appliance is equipped with a cooling system which comes into
operation as soon as a cooking function starts.
Operation of the fans generates a normal air flow which comes out
above the door and may continue for a short time even after the oven
is switched off.
10.6 Inside light
The oven light comes on:
when the oven door is opened in standby status (point “8.2
Operating settings”) or;
when the function knob is turned to any function.
If the oven door is left open, the oven light will automatically shut-off after
10 minutes.
EN
Instructions for the User
21
11 RECOMMENDED COOKING TABLES
For more detailed information about cooking refer to the following tables.
The suggested times and temperatures are guideline values. The actual
cooking time can vary according to the type and quality of the foods.
The levels indicated in the last column of the tables are explained in the
following picture.
The perforated container with the food should preferably be inserted into
the level 2. In this case it is important that the non-perforated container is
introduced into the level 1. This way, dripping liquids are collected and the
appliance does not get dirty.
11.1 Fish
FISH QUANTITY
TEMPERATURE
(ºC)
TIME (MIN.)
CONTAINER LEVEL
GILTHEAD SEA
BREAM
800-1200 G 80 30-40 PERFORATED 2
TROUT 4 X 250 G 80 20-25 PERFORATED 2
SALMON FILET 500-1000 G 80 15-25 PERFORATED 2
SALMON
TROUT
1000-1200 G 80 25-35 PERFORATED 1/2
KING PRAWNS 500-1000 G 80 15-20 PERFORATED 2
GREEN-SHELL
MUSSEL
1000-1500 G 100 25-35 PERFORATED 2
HALIBUT FILET 500-1000 G 80 20-25 PERFORATED 2
COCKLES 500-1000 G 100 10-20 PERFORATED 2
LOBSTER 800-1200 G 100 25-30 PERFORATED 1/2
COD FILET 1000-1200 G 80 20-25 PERFORATED 2
BLUE MUSSEL 1000-1200 G 100 15-25 PERFORATED 2
LAKE TROUT 4 X 250 G 80 25-30 PERFORATED 2
HADDOCK 1000-1200 G 80 20-25 PERFORATED 2
TUNA FILET 500-1000 G 80 15-20 PERFORATED 2
PIKE PERCH 4 X 250 G 80 25-30 PERFORATED 2
EN
Instructions for the User
22
11.2 Meat
MEAT QUANTITY
TEMPERATURE
(ºC)
TIME (MIN.)
CONTAINER LEVEL
CHICKEN LEG 4-10 100 40-45 PERFORATED 2
CHICKEN
BREAST
4-6 100 25-35 PERFORATED 2
SMOKED PORK
LOIN
500G – 1000 G
100 40-50 PERFORATED 2
TURKEY
ESCALOPE
4-8 100 20-25 PERFORATED 2
PORK FILET,
WHOLE
4-8 100 20-30 PERFORATED 2
SAUSAGES 80-100 10-15 PERFORATED 2
11.3 Eggs
EGGS TEMPERATURE (ºC) TIME (MIN.) CONTAINER LEVEL
EGGS IN GLASS 100 10-15 RACK 2
EGGS, HARD 100 15 RACK 2
EGGS, SOFT 100 10-12 RACK 2
11.4 Side dishes
SIDE DISHES QUANTITY
TEMPERATURE
(ºC)
TIME
(MIN.)
CONTAINER LEVEL
PEARL BARLEY +
LIQUID
200G + 400 ML 100 30-35 RACK, 2
SEMOLINA +
LIQUID
200G + 300 ML 100 10-20 RACK 2
LENTILS +
LIQUID
200G + 375 ML 100 20-50 RACK 2
RICE + LIQUID 200G + 250 ML 100 25-40 RACK 2
EN
Instructions for the User
23
11.5 Vegetables
VEGETABLES
TEMPERATURE
(ºC)
TIME (MIN.)
CONTAINER LEVEL
EGGPLANT/AUB
ERGINE
IN SLICES
100 15-20 PERFORATED 2
BEANS
100 35-45 PERFORATED 2
BROCCOLI
FLORETS WITH
STALK
100 25-30 PERFORATED 2
BROCCOLI
FLORETS
WITHOUT STALK
100 15-20 PERFORATED 2
CAULIFLOWER
FLORETS
100 25-30 PERFORATED 2
CAULIFLOWER
WHOLE HEAD
100 40-45 PERFORATED 1
PEAS
100 30-35 PERFORATED 2
FENNEL
IN STRIPES
100 15-20 PERFORATED 2
FENNEL
CUT IN HALF
100 20-30 PERFORATED 2
POTATOES
WITH SKIN
WHOLE, VERY
SMALL
100 20-25 PERFORATED 2
POTATOES
WITH SKIN
WHOLE, VERY
BIG
100 45-50 PERFORATED 2
POTATOES
WITHOUT SKIN
IN PIECES
100 20-25 PERFORATED 2
TURNIP
IN STICKS
100 20-25 PERFORATED 2
SNOW PEAS
100 15-20 PERFORATED 2
CARROTS
IN SLICES
100 25-30 PERFORATED 2
CORN COBS
100 50-60 PERFORATED 2
BELL PEPPERS
IN STRIPES
100 12-15 PERFORATED 2
HOT PEPPER
100 12-15 PERFORATED 2
MUSHROOMS
IN QUARTERS
100 12-15 PERFORATED 2
LEEKS
IN SLICES
100 10-12 PERFORATED 2
BRUSSELS
SPROUTS
100 25-35 PERFORATED 2
CELERY
IN STRIPES
100 15-20 PERFORATED 2
ASPARAGUS
100 20-35 PERFORATED 2
SPINACH
100 12-15 PERFORATED 2
CELERY
STALKS
100 25-30 PERFORATED 2
COURGETTE
IN SLICES
100 12-18 PERFORATED 2
EN
Instructions for the User
24
11.6 Dumplings
DUMPLINGS TEMPERATURE (ºC) TIME (MIN.) CONTAINER LEVEL
SWEET DUMPLING 100 20-30 NOT PERFORATED 2
SWEET YEAST
DUMPLING
100 15-20 NOT PERFORATED 2
YEAST DUMPLING 100 15-25 NOT PERFORATED 2
BREAD DUMPLING 100 20-25 NOT PERFORATED 2
NAPKIN DUMPLING 100 25-30 NOT PERFORATED 2
11.7 Desserts
DESSERTS QUANTITY
TEMPERATURE
(ºC)
TIME
(MIN.)
CONTAINER LEVEL
STEWED APPLES 500-1500 G 100 15-25 NOT PERFORATED
2
STEWED PEARS 500-1500 G 100 25-30 NOT PERFORATED
2
CRÈME BRÛLÉE 80 20-25 RACK 2
CRÈME CARAMEL 80 25-30 RACK 2
YOGURT 40 4-6 HRS. RACK 2
STEWED PEACHES 500-1500 G 100 15-20 NOT PERFORATED
2
11.8 Fruit (Sterilising / Boiling down)
FRUIT QUANTITY
TEMPERATURE
(ºC)
TIME
(MIN.)
CONTAINER LEVEL
PEARS 4-6 1L GLASSES 100 30-35 RACK 1
CHERRIES 4-6 1L GLASSES 80 30-35 RACK 1
PEACHES 4-6 1L GLASSES 80 30-35 RACK 1
PLUMS 4-6 1L GLASSES 80 30-35 RACK 1
11.9 Regenerate
WARMING-UP QUANTITY
TEMPERATURE
(ºC)
TIME
(MIN.)
CONTAINER LEVEL
PLATE DISHES 1-2 100 12-15 RACK 2
PLATE DISHES 3-4 100 15-20 RACK 2
READY-MADE MEALS 100 15-20 RACK 2
11.10 Blanch
VEGETABLES QUANTITY
TEMPERATURE
(ºC)
TIME
(MIN.)
CONTAINER LEVEL
E.G. BEANS, LEEK 100 10-12 PERFORATED 2
CURLY KALE 1000-2000 G 100 12-16 PERFORATED 2
SAVOY CABBAGE 10-20 100 12-15 PERFORATED 2
WHITE CABBAGE,
WHOLE
2000-2500 G 100 30-45 PERFORATED 1
TOMATOES, PEELED 80 12 RACK 2
EN
Instructions for the User
25
11.11 Defrost
VEGETABLES / SIDE DISH
TEMPERATURE
(ºC)
TIME (MIN.)
CONTAINER LEVEL
BROCCOLI
FLORETS WITH
STALK
40 15-20 PERFORATED 2
MIXED
VEGETABLES
40 15-20 PERFORATED 2
SPINACH
LEAVES
PORTIONS
40
10-15 NOT PERFORATED 2
CAULIFLOWER
FLORETS
40 15-20 PERFORATED 2
PEAS
40 15-25 PERFORATED 2
CURLY KALE
BIGGER
PORTION
40
25-35 NOT PERFORATED 2
CARROTS
IN SLICES
40 15-20 PERFORATED 2
BRUSSELS
SPROUTS
40
20-25 PERFORATED 2
ASPARAGU
40 25-30 PERFORATED 2
READY-MADE
MEALS
40 AS
REQUIRED
RACK 2
BREAD
40 10-25 RACK 2
RICE
40 15-25 NOT PERFORATED 2
LENTILS
40 15-20 NOT PERFORATED 2
NOODLES
40 15-20 NOT PERFORATED 2
11.12 Two level cooking
Some suggestions:
When cooking with two levels the accessories should be always inserted
in the 2nd or 3rd level and in the 1st level.
Different cooking times are controlled this way:
Foods that need a longer cooking time should be placed in the upper area
of the oven. Foods with a shorter cooking time should be placed on the 1st
level.
One example: Vegetables, potatoes and fish.
Place the vegetables and potatoes in any suitable container on the rack
inserted in the 2nd or 3rd level.
Insert the fish in the 1st level.
When using the perforated tray to cook fish, the non-perforated tray must
be inserted in the bottom of the appliance to collect liquid dripping from the
fish. This way the appliance is kept clean.
Time: Vegetables and potatoes 25-35 Min.
Time: Fish – depending on type – 15-25 Min.
Select the longest cooking time. Because of the different levels the food is
ready at the same time, without any over cooking.
EN
Instructions for the User
26
12 CARE AND MAINTENANCE
12.1 Descaling
Whenever steam is produced, irrespective of the hardness of the local
water supply (i.e. the limescale content of the water), limescale is
deposited inside the steam generator.
The time interval between descaling depends on the hardness of the water
and frequency of use. If steaming 4×30 minutes per week, the appliance
must be descaled (depending on water hardness) roughly as follows:
WATER HARDNESS LEVEL NO. DESCALE AFTER ABOUT
VERY SOFT
SOFT
18 MONTHS
MEDIUM
MED
9 MONTHS
VERY HARD
HARD
6 MONTHS
The appliance automatically detects when descaling is necessary and
when this happens the Descale light turn on. If the Descaling procedure is
not performed, some cooking cycles after the Descale light starts to flash.
If once again the Descaling procedure is not performed, some cooking
cycles after the oven functioning is blocked, the Descale light stays on and
the display shows “CAL” blinking. The oven keep being blocked until the
descale procedure is performed
To run a descale cycle proceed as described in 10.3.2 Descale
function.
IMPORTANT NOTE: Failure to descale the appliance will likely impair
the functioning of or cause damage to the appliance.
12.2 Suitable descaling solutions
For descaling use suitable solution, as Durgol or liquid coffee machine
descaling solutions for example. Solutions containing foam agents are not
appropriate.
Warning! Do not use vinegar or vinegar-based products as they can
cause damage to the oven’s internal circuit.
12.3 Descaling Process
Please see point 10.3.2
12.4 Cleaning the oven
The steam oven cavity and front surface must be cleaned after each use.
All food remains and condensed water must be removed (see section on
Oven Cleaning). If the steam oven is not kept clean its surface may
deteriorate and this may shorten the oven’s working life.
For ease of cleaning, the shelf guides can be removed (see the following
chapter).
IMPORTANT NOTE: Don’t wash the water tank in the dishwasher
machine.
EN
Instructions for the User
27
12.5 Removing the shelf guides
1. Unscrew and remove the knurled nuts 1 in the front of the shelf
guides in an anti-clockwise direction.
2. Unscrew and loosen the knurled nuts 2 in the back of the shelf guides
in an anti-clockwise direction. Do not completely remove these nuts.
3. Pull the shelf guides to the inside of the cavity and remove from the
front.
To put them back, insert the shelf guides into the knurled nuts 2 in the
back and position on the screws in the front.
Screw the knurled nuts 1 and 2 in a clockwise direction till tight.
EN
Instructions for the User
28
12.6 Removing the appliance door
1. Open the appliance door as far as it will go.
2. Insert 2 pins inside the holes in the hinges.
3. Close the appliance door just enough that it can be lifted out.
4. To reassemble, push the hinges into the holes from the front.
5. Open the appliance door as far as it will go and remove the pins.
EN
Instructions for the User
29
13 OVEN CLEANING
Warning!
Cleaning should be done with the oven power switched off.
Take the plug out of the socket or switch off the oven’s power circuit.
Warning!
Do not use aggressive or abrasive cleaning products, scourers
that scratch surfaces or sharp objects, since stains may appear.
To clean
stainless steel parts, please use suitable detergent which does not contain
abrasive or acid substances or chlorine.
Warning! Never use high pressure or steam jet cleaning appliances.
13.1 Front surface
Normally you just need to clean the oven with a damp cloth. If it is very
dirty, add a few drops of dishwashing liquid to the cleaning water.
Afterwards, wipe the oven with a dry cloth.
In an oven with a finger print proof treatment front, use a mild glass
cleaning product and a soft cloth that does not release any fibres or
threads. Wipe from side to side without exerting any pressure on the
surface.
Immediately remove limescale, fat, starch or egg white stains. Corrosion
can occur under these stains.
Do not let any water get inside the oven.
13.2 Oven interior
After use, remove any water on the bottom of the cooking space with a
soft cloth. Leave the appliance door open so that the cooking space can
cool down.
To remove dirt that is harder to shift, use a non-aggressive cleaning
product. Do not use oven sprays or other aggressive or abrasive
cleaning products.
Always keep the door and the oven front very clean to ensure that
the door opens and closes properly.
Make sure water does not enter the oven ventilation holes.
The glass lamp cover is located on the oven ceiling and can be removed
easily for cleaning. For this you just need to unscrew it and clean it with
water and dishwashing liquid.
13.3 Accessories
Clean the accessories after each use. If they are very dirty, soak them first of
all and then use a brush and sponge. The accessories can be washed in a
dish washing machine except the water tank.
EN
Instructions for the User
30
14 EXTRAORDINARY MAINTENANCE
Occasionally, the oven will require minor servicing procedures or the
replacement of parts subject to wear and tear, such as gaskets, light bulbs,
etc. The specific operations for each procedure of this kind are provided below.
Before
carrying out any operation involving access to live parts, disconnect the
appliance from the electricity supply.
14.1 What should I do if the oven doesn’t work?
WARNING! Any type of repair must only be done by a specialised
technician. Any repair done by a person not authorised by the
manufacturer is dangerous.
You do not need to contact Technical Assistance to resolve the following
questions.
Failure description Solution
The display is not
showing!
- The time indication has been switched off (see
section on Operating Settings).
Nothing happens when
I press the keys!
- The Safety Block is active (see section on
Child Safety Lock-out function).
The oven does not
work!
- Check if the plug is correctly fitted in the
socket.
- Check if the oven power is switched on.
When the oven is
operating I can hear
some strange noises!
- It has to do with the operating noises that can
occur during the cooking process, e.g, by the
water pumps in the steam generator.
- The steam inside the cavity produces a
pressure build-up and sometimes the cavity
walls may produce noise when they react to the
pressure.
- These noises are normal, there is no problem.
The food doesn’t heat
up or heats very
slowly!
- You have selected the correct operating times
and temperature setting.
- The food you have put inside the oven is a
larger amount or colder than you usually put in.
The message “Err_”
appears in the display
- Please contact the Customer Care.
The appliance still
makes a noise after
the cooking process is
finished!
This is not a problem. The cooling fan keeps on
working for some time. When the temperature
has dropped sufficiently, the fan will switch itself
off.
The oven switches on
but the interior light
does not go on!
If all the functions work properly it is probable
that the lamp has blown. You can keep on using
the oven.
Display shows Perform water level calibration (see 8.3.2)
EN
Instructions for the User
31
14.2 Replacing the light bulb
To replace the light bulb, proceed as follows:
Disconnect the oven from the power supply. Take the plug out
of the socket or switch off the oven’s power circuit.
Unscrew and remove the glass light cover (1).
Remove the light bulb (2). Warning! The bulb may be very hot.
Fit a new E14 230-240V/15W bulb. Follow the lamp manufacturer’s
instructions. IMPORTANT NOTE: Make sure that the sealing rings (3)
are applied in the correct sequence.
Screw the glass light cover into place (1).
Connect the oven again to the power supply.
15 INSTALLING THE APPLIANCE
15.1 Before installation
Check that the input voltage indicated on the characteristics plate is the
same as the voltage of the power outlet you are going to use.
Open the oven door and take out all the accessories and remove the
packing material.
Warning! The front surface of the oven may be covered in a protective
film. Before using the oven for the first time, carefully remove this film,
starting on the inside.
Make sure that the oven is not damaged in any way. Check that the
oven door closes correctly and that the interior of the door and the front of
the oven opening are not damaged.
DO NOT USE THE OVEN if the power cable or the plug is damaged, if the
oven does not function correctly or if it has been damaged or dropped.
Put the oven on a flat and stable surface. The oven must not be installed
close to any sources of heat, radios or televisions.
EN
Instructions for the Installer
32
During installation, make sure that the power cable does not come
into contact with any moisture or objects with sharp edges and the
back of the oven. High temperatures can damage the cable.
Warning: after the oven is installed you must make sure you can
access the plug.
15.2 Electrical connection
The nameplate with the technical data, serial number and mark is in a
visible position on the oven door frame.
The nameplate must never be removed.
The appliance must be connected to earth in compliance with electrical
system safety regulations.
If a permanent connection is used, the appliance's power supply line must
be fitted with an omnipolar breaking device with contact gap of at least 3
mm, located in an easily accessible position close to the appliance itself.
If a socket and plug connection is used, check that they are of the same
type. Do not use reducers, adapters or junctions since they may cause
overheating or burns.
EN
Instructions for the Installer
33
15.3 Positioning the oven
The appliance is designed for building-in to cabinets made from any heat-
resistant material. Comply with the dimensions shown in following pictures.
When installing in tall units bear in mind that the top/rear of the unit must
have an opening 100 mm deep.
Screw the 4 screws into the inside of the frame.
The manufacturer reserves the right to make any changes deemed useful for
improvement of his products without prior notice. The illustrations and description
contained in this manual are therefore not binding and are merely indicative
… 35

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Smeg-SC45V2

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Smeg SC45V2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Smeg SC45V2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Smeg SC45V2

Smeg SC45V2 Gebruiksaanwijzing - Nederlands - 38 pagina's

Smeg SC45V2 Gebruiksaanwijzing - Deutsch - 39 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info