Handleiding Skytech 3002 (pagina 9 van 10) (Engels)

603162

Verklein

Vergroot

Pagina terug

1/10

Pagina verder

Skytech: 3002

REV. 4-19-12 Page 9

CHILDPROOF “LOCK-OUT” – (CP)

This SKYTECH remote control includes a CHILDPROOF “LOCK-OUT” feature that allows the user to “LOCK-OUT”

operation of the appliance, from the TRANSMITTER.

SETTING “LOCK-OUT” – (CP)

1. To activate the “LOCK-OUT” feature, press and hold the UP

and TIMER/TIME buttons, together, for 5 seconds. The letters

CP will appear in TEMP frame on the LCD screen (Fig. 21).

2. To disengage the “LOCK-OUT”, press and hold the UP and

TIMER buttons, together for 5 seconds or more, and the

letters CP will disappear from the LCD screen and the

transmitter will return to its normal operating condition.

NOTE: If the appliance is already operating in the ON or

THERMO MODES, engaging the “LOCK-OUT” will not cancel the operating MODE. Engaging the “LOCK-OUT” prevents

only the manual operation of the TRANSMITTER. If in the auto modes, the THERMO operation will continue to operate

normally. To totally “LOCK-OUT” the operation of the

TRANSMITTER’S operating signals; the transmitter’s MODE must be set to OFF.

ROOM

SET

Fig. 21 Child Protection (CP)

MODE

TIMER

TIME

SET

BATTERY LIFE

Life expectancy of alkaline batteries should be at least 12-months. Check and replace all batteries annually. When the

Transmitter no longer operates the receiver from a distance it did previously (i.e., the transmitter’s range has decreased)

or the remote receiver does not function at all, the batteries should be checked. It is important that the remote receiver

batteries are fully charged, providing a combined output voltage of at least 5.3 volts. The length of the wire between the

remote receiver and the gas valve directly affects the operating performance of the remote system. The longer the wire,

the more battery power is required to deliver signals between the remote receiver and the gas valve. The Transmitter

should operate with as little as 2.5 volts of battery power, measuring at the (2) 1.5-volt batteries.

TROUBLE SHOOTING

Should you encounter problems with your replace system, the problem may be with the replace itself or it could be with

the SKYTECH remote control. Review the replace manufacturer’s operation manual to make sure all connections are

properly made. Then check the operation of the SKYTECH remote in the following manner:

1. Make sure receiver batteries are installed properly. If one battery is installed backward, receiver will not operate in

remote mode. Be sure battery output is 2.5 volts or more. (Slide switch is independent of battery condition.)

2. Be sure the transmitter’s batteries are properly installed and that the battery output is 2.5 V or more.

3. Check to make sure the transmitter is communicating with the receiver.

• If the receiver beeps when the MODE button is depressed on the transmitter they are communicating.

Note: The receiver only beeps in ON & OFF modes. No beeping occures from ON to Thermo mode.

• If the receiver does not beep when the MODE button is depressed on the transmitter, you will need to “learn”

(teach) the receiver the code of the transmitter. See page 5 Learning Transmitter to Receiver section.

4. Make sure the transmitter is within the 15 to 20-foot range of the receiver.

5. Positioning of the receiver is important. If the receiver is “enclosed” in a metal surround, the operation of the

receiver may be affected as noted below. Reposition the receiver to improve operating range. It is suggested that a

heat shield be installed to protect the receiver from extreme heat. If the receiver is “enclosed” in a metal surround, this

can:

• Cause the RF signal to get lost and not communicate with the receiver.

• Cause the working distance to be shorter than normal.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Skytech 3002 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info