490931
8
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
TALKOVER
Channel 1 features an auto talkover function that is switched on via the TALKOVER button (9). When
a signal of more than -3dB is applied to channel 1, the channels 2 to 6 are attenuated by 16dB so that
the microphone sound from channel 1 is clearly audible.
ECHO
Every channel features an ECHO EFFECT. Set the START/STOP switch (21) to START. Set the
balance between the echo signal and the channel sound via the EFFECT control (7). Set the required
effect via the controls REPEAT, DELAY and ECHO (18, 19 and 20).
CROSSFADER FUNCTION
This slider control allows you to switch quickly between the sounds of two different channels.
Example: Set the left ASSIGN button (12) to channel 1 and the right ASSIGN button to channel 2. If
you push the crossfader to the left, you hear only channel 1. If you push the crossfader to the right,
you can hear only channel 2. The slider controls of the two channels must of course be lifted. You can
make any combination of the two ASSIGN buttons. The crossfader function is switched off via the
CUT switch (11).
MASTER SECTION
The MASTER 1 & 2 controls (22, 23) set the total output level via both channels to the amplifier. The
level is clearly displayed on the stereo LED VU-meter (if master volume has been selected via the
MASTER/PFL switch). Always set the level in such a way that the red LEDs light up only shortly in
order to prevent overdrive. The RCA connectors for the connection to the amplifier are located at the
rear panel. They are identified as MASTER 1 & 2 (33, 34). Next to the MASTER outputs is another
stereo RCA connector marked REC (32) for connection of the output signal to a cassette or tape
recorder.
HEADPHONE SECTION
Connect a stereo headphone fitted with a 6.3mm jack plug to connector (25).Select the input channel
or the MASTER output signal to which you want to listen via the push-buttons next to the slider
controls of each channel. Set the volume via the PFL LEVEL (24) knob.
SWITCHING ON
Once the audio sources and the amplifier have been connected to the mixer, set all slider controls to
the minimum. Only then switch on the power of the mixer (15) and after that, the amplifier.
REPLACEMENT OF THE CROSSFADER
This control is used very frequently and needs replacement after some time. This is simple to do.
Remove the two small screws on the small panel of the control with a cross-headed screwdriver. Pull
out the control and unplug the connectors. Plug the connectors back to a new crossfader (this can
only be done in one way), insert the control back into the mixer and fasten the two screws.
POSSIBLE WIRING OF THE COMBINED MICROPHONE INPUT
1 = Ground (earth)
2= Signal +
3= Signal -
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skytec TEC 450 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skytec TEC 450 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info