g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR ANGLE GRINDERS
GENERAL
● Only use this tool for dry grinding/cutting
● Only use the flanges which are supplied with this tool
● This tool should not be used by people under the age of
16 years
● Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
● Use the original SKIL accessories which can be
obtained from your SKIL dealer
● For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
● Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
● Do not use damaged, deformed or vibrating grinding/
cutting discs
● Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
● Protect accessories from impact, shock and grease
● Do not use a grinding/cutting disc that is larger than the
maximum recommended size
● Only use grinding/cutting discs with a hole diameter
which fits mounting flange D 6 without play; never use
reducors or adaptors to fit large-hole grinding/cutting
discs
● Never use grinding/cutting discs with a threaded hole, of
which the thread is not long enough to accept the
spindle length of the tool
● Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
● Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
● Only use an extension cord which is intended for
outdour use and equipped with a splashproof coupling-
socket
BEFORE USE
● Before using the tool for the first time, it is recommended
to receive practical information
● Do not work with materials containing asbestos
● Be careful of hidden electrical wires or gas- and water
pipes; check the work area, for instance with a metal
detector
● Be careful when cutting groves, especially in supporting
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be
observed under all circumstances, so before beginning
work, consult with the responsible structural engineer,
architect or construction supervisor)
● Clamp the workpiece in case it does not remain
stationary from its own weight
● Do not clamp the tool in a vice
● Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
● Wear protective glasses and gloves, hearing
protection 3, a dust mask, and sturdy shoes; when
necessary, also wear an apron
● Always mount auxiliary handle A 6 and protective guard
B 6; never use the tool without them
● Be sure tool is switched off when plugging in
DURING USE
● Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
● If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug;
never use the tool with a damaged cord
● Push spindle-lock button G 6 only when spindle C 6 is
at a standstill
● Keep hands away from rotating accessories
● When grinding metal, sparks are generated; keep other
persons and combustible material from work area
● In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
● In case the cutting disc is blocked, resulting in jerking
forces on the tool, immediately switch off the tool
● In case of current interruption or when the plug is
accidentally pulled out, unlock the on/off switch
immediately and put it in the OFF-position in order to
prevent uncontrolled restarting
● Do not apply so much pressure on the tool that it comes
to a standstill
AFTER USE
● Before you put down the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
● After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
● Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
● If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
● Mount auxiliary handle A 4
● Mount protective guard B 5
! ensure that the closed side of the protective
guard always points to the operator
● Mounting of accessories 6
! disconnect the plug
- clean spindle C and all parts to be mounted
6
