390817
5
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
! never use a grinding/cutting disc without the label
(“blotter”) which is glued onto it
Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
On/off locking switch H 7
- switch on tool 7a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 7b
- unlock switch/switch off tool 7c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
Grinding 8
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
Cutting 9
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
Holding and guiding the tool
- always hold the tool firmly with both hands, so you will
have full control of the tool at all times
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots J 6 clear and uncovered
APPLICATION ADVICE
Instead of flange E 6 the CLIC quick-clamping flange
K 6 (SKIL accessory 2610388766) can be used;
grinding/cutting discs can then be mounted without the
use of accessory keys
GUARANTEE / ENVIRONMENT
Always keep tool and cord clean (especially the
ventilation slots)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
Dispose of the tool by sorting tool, accessories and
packaging for environment-friendly recycling (the plastic
components are labeled for categorized recycling)
INTRODUCTION
Cet outil sert au meulage, au tronçonnage et à
l'ébarbage de pièces en métal et en pierre sans utiliser
de l'eau; combiné avec des accessoires spécifiques, cet
outil peut également servir au brossage et au ponçage
SPECIFICATIONS TECHNIQUES 1
SECURITE
GENERALITES
Lire et conserver ce manuel d'instruction (faire en
particulier très attention aux instructions de sécurité au
dos de ce manuel) 2
Utiliser uniquement cet outil pour le meulage et le
tronçonnage à sec
Utiliser uniquement les brides livrées avec l'outil
Cet outil est interdit aux jeunes n'ayant pas atteint l'âge
de 16 ans
Toujours débrancher l’outil avec tout réglage ou
changement d’accessoire
ACCESSOIRES
Utiliser les accessoires d'origine SKIL en vente chez
votre concessionnaire SKIL
Pour le montage et l'utilisation d'accessoires n'étant pas
de la marque SKIL, observer les instructions du fabricant
concerné
La vitesse admissible des accessoires utilisées doit être
au moins aussi élevée que la vitesse à vide maximale de
loutil
N'utiliser jamais de disques de meulage/tronçonnage
endommagés, déformés ou vibrants
Traiter et stocker les disques de meulage/tronçonnage
avec précaution pour éviter de les endommager
Protéger les accessoires contre les impacts, les chocs et
la graisse
Ne pas utiliser une dimension de disques à
meuler/tronçonner autre que le diamètre recommandé
Utiliser uniquement les disques de meulage/tronçonnage
dont l'orifice s'adapte parfaitement à la bride de montage
D 6; n'utilisez jamais de réducteurs ni d'adaptateurs
pour ajuster des disques ayant un orifice plus grand
Ne jamais utiliser de disques de meulage/tronçonnage
ayant un orifice fileté dont le filet n'est pas suffisamment
longue pour recevoir la longueur de larbre de l'outil
Ne jamais utiliser d'accessoires avec un orifice fileté
borgne plus petit que M14 x 21 mm
UTILISATION A L'EXTERIEUR
Brancher l'outil par l'intermédiaire d'un coupe-circuit (FI)
avec courant de réaction de 30 mA au maximum
5
XP SKIL 9160/9165/9170/9175.2 17-06-2003 10:37 Pagina 5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 9160 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 9160 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info