482021
7
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
7
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR SANDERS
GENERAL
This tool should not be used by people under the age of
16 years
This tool is not suitable for wet sanding
Never use the tool when cord is damaged; have it
replaced by a qualied person
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
SKIL can assure awless functioning of the tool only
when original accessories are used
Do not continue to use worn, torn or heavily clogged
sanding discs
BEFORE USE
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
The noise level when working can exceed 85 dB(A); wear
ear protection
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classied as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
materials you want to work with
Wear protective gloves, safety glasses, close-tting
clothes and hair protection (for long hair)
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
When sanding metal, sparks are generated; do not use
dustbox and keep other persons and combustible
material from work area
DURING USE
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
Do not touch the moving sanding disc
In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
When you put away the tool, switch o the motor and
ensure that all moving parts have come to a complete
standstill
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Backing pads
- never run the tool without backing pad A
! replace damaged backing pads immediately
(loosen/fasten 4 pad screws B)
! unplug tool before removing/mounting backing
pads
Mounting sanding discs
- simply press sanding disc C onto backing pad with
perforation in sanding disc corresponding with
perforation in backing pad
- if necessary, clean backing pad rst
! the dust suction requires the use of perforated
sanding discs
Dust suction 4
- empty dustbox D regularly for optimal dust pick-up
performance
- remove dustbox D by pushing knob J to the left and
hold it in that position while pulling dustbox D
backwards
- mount dustbox D by sliding it back until it clicks into
place
! do not use dustbox when sanding metal
Pressure control 5 (7450/7460)
Warns the user when applying too much pressure on the
tool while working (too much pressure reduces the
sanding performance)
- green light 1 turns on in case of pressure
- green light 2/3 turns on in case of increased pressure
- red light 4 turns on when pressure is too high
NOTES:
! the pressure control feature only starts working
properly after the tool has run for approximately
one minute
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 7450 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 7450 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 9,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info