758582
14
Verklein
Vergroot
Pagina terug
1/172
Pagina verder
14
! be aware of the sudden impact when the tool is
switched on
! the tool should run at full speed before the blade
enters into the workpiece
! do not force the tool (apply light and continuous
pressure in order to avoid overheating the blade

plastic material)
! 
coloured grip area(s) y
-after completing the cut switch o tool by releasing
trigger B
! ensure that the blade has come to a complete

workpiece
Plunge cutting u
-switch on the tool
! the tool should run at full speed before the blade
enters into the workpiece
-press knob M with your thumb
-tilt tool forward with line-of-cut indicator R lined up with
desired line of cut marked on the workpiece
-gradually move tool forward
! never pull tool backwards
Parallel guide S i
-for making exact cuts along a workpiece edge
-can be inserted in either side of foot
Adjusting parallel guide
-loosen knob T
-adjust to desired cutting width by using parallel guide
scale (use line-of-cut indicator R as 0-reference)
-tighten knob T
APPLICATION ADVICE
Only use sharp saw blades of the correct type o
-use hardened steel saw blade V 2 for cutting wood,
aluminium, plastic and all sorts of laminated wood
-use diamond disc W 2 for cutting ceramics and tiles
-carbide tipped blades X 2 stay sharp up to 30 times
longer than ordinary blades
Cutting large panels p
-support panel close to the cut either on oor, table or
workbench
! set cutting depth so that you cut through panel
and not through support
-in case parallel guide does not allow desired width of
cut, clamp or nail straight piece of wood to workpiece
as a guide, and use the left side of the foot against this
guide
Splinter-free cutting
-always face the good side of the workpiece down
-fasten a straight piece of wood on the workpiece by
means of 2 clamps
For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool and cord clean (especially ventilation
slots Y 2)
! disconnect the plug before cleaning
Always keep the area around lower guard Z 2 clean
(remove dust and chips by blowing out with compressed
air or with a brush)
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
On/o 8
-switch on tool by rst pressing knob A forward and then
pulling trigger switch B
-switch o tool by releasing trigger switch B
Adjusting cutting depth (0-28,5 mm) 9
-loosen knob C
-set desired cutting depth using scale D
-tighten knob C
-for an optimal quality cut the saw blade should not
extend more than 3 mm below the workpiece
! 
cutting depth corresponds with value on cutting
depth scale D (for actual depth of cut use table q
as reference)
! 
cut
Dust suction w
-connect vacuum cleaner hose E to connection F and
vacuum cleaner as illustrated
! never let the vacuum cleaner hose interfere with
the lower guard or the cutting operation
! do not use vacuum cleaner when cutting metal
Changing saw blade e
! disconnect the plug
! ensure that the blade has come to a complete
standstill
-set cutting depth to the maximum
-take hex key G from storage H
-push spindle-lock button J and hold it while you remove
blade boltK by turning hex key G CLOCKWISE (= in
same direction as arrow printed on saw blade)
! push spindle-lock button J only when tool is at a
standstill
-release spindle-lock button J
-remove ange L
-press knob M with your thumb
-lift up foot N and remove saw blade
! change saw blade with saw teeth and arrow
printed on saw blade pointing in same direction as
arrow on upper guard P e b
-mount ange L
-rmly tighten blade bolt K by turning hex key G
COUNTER-CLOCKWISE while pushing spindle-lock
button J
-release spindle-lock button J
Operating the tool r
-set desired cutting depth
-connect plug to power source (light Q turns on
indicating that the tool is receiving power) t
-press knob M with your thumb
-place tool with front end of foot at on workpiece
-tilt tool forward with line-of-cut indicator R lined up with
desired line of cut marked on the workpiece
! ensure that the saw teeth are not engaged into the
workpiece
-switch on the tool
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 5360 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 5360 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 8,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info