758357
6
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
General Specifications
Voltage Rating . . . . . . . . . . . . . . . . . . .120 V, 60 Hz
Amperage Rating . . . . . . . . . . . . . . . . . . . . . . .1.2 A
No Load Speed . . . . . . . . .No500-1,700/min (SPM)
Throat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16"
Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . .5” pin-end
Blade Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . .7/8"
Cutting Capacity . . . . . . . . . . . . . . . . . . . . .2" at 90°
Table Tilt . . . . . . . . . . . . . . . . . . . . . . . to 45° Left
Motor Specifications
In the event of a malfunction or breakdown, grounding pro-
vides a path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with an elec-
tric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a match-
ing outlet that is properly installed and grounded in accor-
dance with all local codes and ordinances.
This Scroll Saw is designed to use a 1700 RPM motor. It is
wired for operation on 110-120 volts, 60 Hz. alternating cur-
rent. Before connecting the motor cord to power source,
make certain the switch is in the “OFF” position and be sure
the electric current is of the same characteristics as
stamped on the scroll saw nameplate.
Connection ToAPower Source
This machine must be grounded while in use to protect the
operator from electric shock.
Plug power cord into a 110-120V properly grounded type
outlet protected by a 15-amp dual element time delay fuse
or circuit breaker.
Not all outlets are properly grounded. If you are not sure
that your outlet, as pictured in Fig. 1, is properly
grounded; have it checked by a qualified electrician.
To avoid electric shock, do not touch
the metal prongs on the plug when
installing or removing the plug to or from the outlet.
Failure to properly ground this power
tool can cause electrocution or seri-
ous shock, particularly when used near metal
plumbing or other metal objects. If shocked, your
reaction could cause your hands to hit the tool.
If power cord is worn, cut or damaged
in any way, have it replaced immedi-
ately to avoid shock or fire hazard.
Your unit is for use on 120 volts; it has a plug that looks
like the one in Figure 1.
This power tool is equipped with a 3-conductor cord and
grounding type plug, approved by Underwriters
Laboratories and the Canadian Standards Association.
The ground conductor has a green jacket and is
attached to the tool housing at one end and to the
ground prong in the attachment plug at the other end.
If the outlet you are planning to use for this power tool is
of the two-prong type, DO NOT REMOVE OR ALTER
THE GROUNDING PRONG IN ANY MANNER.. Have a
qualified electrician replace the TWO-prong outlet with a
properly grounded THREE-prong outlet.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The con-
ductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-
conductor. If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely under-
stood, or if in doubt as to whether the tool is properly
grounded.
Always use proper extension cord. The use of any exten-
sion cord will cause some loss of power. To keep this to
aminimum and to prevent overheating and motor burn-
out, use the table below to determine the minimum wire
size (A.W.G.) extension cord. Use only 3-wire extension
cords which have 3-prong grounding type plugs and 3-
pole receptacles which accept the tool’s plug. Make sure
your extension cord is in good condition.
Extension Cord Length Wire Size A.W.G.
0-25 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
26-50 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
51-100 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
6.
Motor Specifications and Electrical Requirements
“SAVE THESE INSTRUCTIONS”
DANGER
!
DANGER
!
WARNING
!
FIG. 1
SM 2610957121 05-08 6/5/08 7:35 AM Page 6
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 3335-01 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 3335-01 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 3,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info