757991
10
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
1 0
C h anging direc t ion of rot at ion 9
-w h en not properly se t in left / righ t posi t ion, s w it c h A 2
c annot be ac t ivat ed
! change direction of rotation only when tool is at a
complete standstill
C h anging bit s q
! do not use bits with a damaged shank
Torq ue c ont rol ( VariTorq ue) w
-out put t orq ue w ill inc rease as c lut c h ring B is rot at ed
from 1 t o 1 7 ; posi t ion C w ill loc k up t h e c lut c h t o perm it
drilling or driving h eavy dut y w ork
-when turning in a screw, rst try VariTorque position 1
and inc rease unt il t h e desi red dept h h as been reac h ed
Mec h anic al gear se lec t ion e
-se t se lec t or D t o desi red sp eed
! actuate the gear selector while tool is running
slowly
1
-low sp eed
-h igh t orq ue
-for sc rew driving and drilling large diam et ers
-for t apping t h read
2
-h igh sp eed
-low er t orq ue
-for im pac t drilling
-for drilling sm all diam et ers
H olding and guiding t h e t ool t
! while working, always hold the tool at the grey-
coloured grip area(s)
-keep vent ilat ion sl ot s H 2 unc overed
-do not apply t oo m uc h pressu re on t h e t ool; let t h e t ool
do t h e w ork for y ou
APPLICATION ADVICE
U se t h e appropriat e bit s y
! only use sharp bits
W h en drilling ferrous m et als
-pre- drill a sm aller h ole, w h en a large h ole is req uired
-lubric at e drill bit oc c asi onally w it h oil
W h en t urning in a sc rew at / near t h e c ross c ut end or an
edge of w ood, pre- drill a h ole in order t o avoid c rac king
of t h e w ood
For an optimal use of the tool a steady pressure on the
sc rew is req uired, esp ec ially w h ile rem oving
W h en sc rew driving in h ard w ood one sh ould pre- drill a
h ole
Splint erfree drilling in w ood u
Dust free drilling in w alls i
Drilling in t iles w it h out ski dding o
For more information see www.skil.com
MAINTENANCE / SERVICE
Th is t ool is not int ended for professi onal use
Alw ay s keep t ool c lean ( esp ec ially vent ilat ion sl ot s H 2)
! remove battery from tool before cleaning
If t h e t ool sh ould fail desp it e t h e c are t aken in
m anufac t uring and t est ing proc edures , repair sh ould
be c arried out by an aft er- sa les se rvic e c ent re for SKIL
pow er t ools
-se nd t h e t ool undismantled t oget h er w it h proof of
purc h as e t o y our dealer or t h e nearest SKIL se rvic e
st at ion ( addresse s as w ell as t h e se rvic e diagram of t h e
t ool are list ed on w w w . ski l. c om )
full c apac it y of t h e bat t ery , c om plet ely c h arge t h e bat t ery
in t h e bat t ery c h arger before usi ng y our pow er t ool for t h e
rst time)
Only use the following batteries and chargers with
this tool
-SKIL battery: BR1*31****
-SKIL charger: CR1*31****
Do not use bat t ery w h en dam aged; it sh ould be replac ed
im m ediat ely
Do not disa sse m ble t h e bat t ery
Do not exp ose t ool/ bat t ery t o rain
Permitted ambient temperature (tool/charger/battery):
-w h en c h arging 4. . . 40° C
-during operat ion –2 0. . . + 50° C
-during st orage –2 0. . . + 50° C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 R ead t h e inst ruc t ion m anual before use
4 Batteries may explode when disposed of in re, so do not
burn bat t ery for any reaso n
5 St ore t ool/ c h arger/ bat t ery in loc at ions w h ere t em perat ure
w ill not ex c eed 50° C
6 Do not disp ose of elec t ric t ools and bat t eries t oget h er
w it h h ouse h old w ast e m at erial
USE
Combined switch for on/o and speed control A 2
-c ont rol t h e sp eed st eplessl y from z ero t o m axi m um by
put t ing less or m ore pressu re on t h e t rigger
C h arging bat t ery
! read the safety warnings and instructions
provided with the charger
R em oving/ inst alling t h e bat t ery 2
At t ac h ing belt c lip 7
-at t ac h t h e belt c lip J t o t h e drill w it h t h e su pplied sc rew .
Bat t ery level indic at or 8
-press t h e bat t ery level indic at or but t on K t o sh ow t h e
c urrent bat t ery level 8a
! when the lowest level of the battery indicator
8b, the
battery is empty
! 
after pressing button K 8c, the battery is not
within the allowable operating temperature range
LED- ligh t r
LED- ligh t aut om at ic ally ligh t s on w h en ac t ivat ing t h e on/
o switch
! 
protection is activated (see below)
Bat t ery prot ec t ion
The tool is suddenly being switched o or prevented from
being s w it c h ed on, w h en
-the load is too high - - > rem ove load and rest art
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C - - > 2
levels of the battery level indicator start ashing when
pressi ng but t on K 8c ; w ait unt il bat t ery h as ret urned
w it h in t h e allow able operat ing t em perat ure range
-the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
bat t ery level 8b is sh ow n by t h e bat t ery level indic at or
w h en pres si ng but t on K; c h arge bat t ery
! 

damaged
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Skil 3008 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Skil 3008 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info